• KSBB Journal
• /
• v.25 no.5
• /
• pp.483-489
• /
• 2010

Biodiesel has attracted great attention as an alternative renewable energy source for the replacement of petroleumbased diesel fuel, yet its high production cost due to expensive oil feedstock remainsas the major economical obstacle. In this study, we investigated catalysts and reaction conditions for the acid catalyzed pre-conversion of free fatty acid (FFA) to fatty acid methyl ester (FAME) in cheap low-grade oils of high acid value. The NaOH base catalyzed reaction of vegetable oil of the initial acid value of 2 mg KOH/g led to a high FAME conversion above 95.4%, but the conversion abruptly decreased at higher initial acid values. This base catalyzed reaction was practically ineffective displaying the FAME conversion below 15% even at the initial acid value of 10 mg KOH/g by the severe saponification side reaction. Among the various catalysts studied for the pre-conversion of FFA to FAME, Amberlyst-15 was the most effective in reducing the acid value, and the optimum reaction condition identified was $65^{\circ}C$ with oil to methanol ratio of 1:3 and catalyst concentration of 15% (w/w). As the results, great enhancements in the overall biodiesel conversion were achievable via a consecutive reaction of the acid catalyzed FFA pre-conversion to FAME under the optimal condition obtained with Amberlyst-15 followed by the NaOH base catalyzed reaction, far above the extent which was obtainable by the single NaOH catalyzed reaction.

• Resources Recycling
• /
• v.10 no.3
• /
• pp.51-59
• /
• 2001

Impurities removal from waste carbon black was carried out to produce high-grade carbon black. A large amount of hydrophilic carbon black is produced as a byproduct of the hydrogen production process by flame decomposition of water. Due to its impurities content such as sulphur, iron, ash, etc., it can only be used as low-grade carbon or burnt out. High-grade hydrophilic carbon black is 3~5 times more expensive than oil-based carbon black because of high production cost associated with process complexly and pollutant treatment. Hydrophilic carbon is normally used for conductive materials for batteries, pigment for plastics, electric wire covering, additives for rubber, etc. In these applications, impurity content must be blow 1 fe. In this study, magnetic separation, froth flotation and ultrasonic treatment were employed to remove impurities from the low-grade hydrophilic carbon black. Results showed that the ash, iron and sulphur content of product decreased to less than 0.01 wt.%, 0.01 wt.% and 0.3 wt % respectively and the surface area of product was about 930 $m^2$/g for conductive materials.

• The Korean Nurse
• /
• v.29 no.3
• /
• pp.25-35
• /
• 1990

It is a fact that there are recent increasing trends or incidence of the colorectal carcinoma among other colorectal diseases. In such trend, the early detection remain to be most important by the air contrast barium enema and total colonofiberscopy. There are several ways to prepare the colon for barium enema and colonofiberscopy which include several agents. The mechanical cleansing have been used most frequently since Brown's method was adapted to be most perfect for colon deansing. The ideal laxatives and enema solutions were limited to adequate dose, it's effectiveness, patient's diet and bowel habit, minimal side effect, low cost and simple to perform. In order to compare the effectiveness of various cleansing solutions, six experimental methods were formed as shown; 1. normal saline enema, 2. castor oil with normal saline enema, 3. castor oil with soap suds enema, 4. magnesium citrate with normal saline, 5. magnesium citrate with soap suds enema and 6. ingestion of Golyetly solution. The authors have compared and determined the degree of cleanness by an experienced endoscopist. The total number of patients was 247, age distribution was $43{\pm}15$ years old, and sex distribution was 133 males and 114 females. The grade I and II represented no difficulties at performing the colonofiberscopy, but grade ill and N had some difficulties, even unable to perform the colonofiberscopy. The effectiveness the cleansing agents, represented with grade I and II was 95.9% (47/49) in method 6, 93.2%(54/58) in method 2, 83.3%(30/33) in method 3, 70.0%(28/10) in method 5, 66.7%(16/24) in method i, and 45.7%(18/40) in method 4. Method 2 and 6 were the most effective in normal bowel habit patients. In constipated patients, method 6 was the most effective and all method except method 11 were effective in diarrhea patients. The degrees of less mucosal irritation by various bowel cleansing method were in the order of method 6(100%), 1(100%), 5(74%), 2(69%). In subjective symptoms and cleansing groups, abdominal distension, pain, nausea and vomiting were complained, and that's subject symptoms were in the order of method 3(88.9%), 6 (79.6%), 1(75%), 5(72.5%), 2(72.4%), 4(67.5%). In conclusion, we believe that the Golytely of the mechanical cleansing solution for colonofiberscopy was the most effective, but others depended on the patient's condition und bowel habit.

• International Journal of Highway Engineering
• /
• v.18 no.6
• /
• pp.97-104
• /
• 2016

OBJECTIVES : The objective of this research is to develop additives for the modification of Solvent DeAsphalting Residue (SDAR) to be used as pavement materials, and evaluate the performance of asphalt mixture manufactured using the SDAR modified by developed additives. METHODS : The SDAR generally consists of more asphaltenes and less oil components compared to the conventional asphalt binder, and hence, the chemical/physical properties of SDAR are different from that of conventional asphalt binder. In this research, the additives are developed using the low molecular oil-based plasticizer to improve the properties of SDAR. First, the chemical property of two SDARs is analyzed using SARA (saturate, aromatic, resin, and asphaltene) method. The physical/rheological properties of SDARs and SDARs containing additives are also evaluated based on PG-grade method and dynamic shear-modulus master curve. Second, various laboratory tests are conducted for the asphalt mixture manufactured using the SDAR modified with additives. The laboratory tests conducted in this study include the mix design, compactibility analysis, indirect tensile test for moisture susceptibility, dynamic modulus test for rheological property, wheel-tracking test for rutting performance, and direct tension fatigue test for cracking performance. RESULTS : The PG-grade of SDARs is higher than PG 76 in high temperature grades and immeasurable in low temperature grades. The dynamic shear modulus of SDARs is much higher than that of conventional asphalt, but the modified SDARs with additives show similar modulus compared to that of conventional asphalt. The moisture susceptibility of asphalt mixture with modified SDARs is good if, the anti-stripping agent is included. The performance (dynamic modulus, rutting resistance, and fatigue resistance) of asphalt mixture with modified SDARs is comparable to that of conventional asphalt mixture when appropriate amount of additives is added. CONCLUSIONS : The saturate component of SDARs is much less than that of conventional asphalt, and hence, it is too hard and brittle to be used as pavement materials. However, the modified SDARs with developed additives show comparable or better rheological/physical properties compared to that of conventional asphalt depending on the type of SDAR and the amount of additives used.

• Clean Technology
• /
• v.27 no.2
• /
• pp.190-197
• /
• 2021

Kraft lignin is a by-product of the pulp and paper industry, obtained as a black liquor after the extraction of cellulose from wood through the Kraft pulping process. Right now, kraft lignin is utilized as a low-grade boiler fuel to provide heat and power but can be converted into high-calorific biofuels or high-value chemicals once the efficient catalytic depolymerization process is developed. In this work, the multi-functional catalyst of Ru-Mg-Al-oxide, which contains hydrogenation metals, acid, and base sites for the effective depolymerization of kraft lignin are prepared, and its lignin depolymerization efficiency is evaluated. In order to understand the role of different active sites in the lignin depolymerization, the three different catalysts of MgO, Mg-Al-oxide, and Ru-Mg-Al-oxide were synthesized, and their lignin depolymerization activity was compared in terms of the yield and the average molecular weight of bio-oil, as well as the yield of phenolic monomers contained in the bio-oil. Among the catalysts tested, the Ru-Mg-Al-oxide catalyst exhibited the highest yield of bio-oil and phenolic monomers due to the synergy between active sites. Furthermore, in order to maximize the extent of lignin depolymerization over the Ru-Mg-Al-oxide, the effects of reaction conditions (i.e., temperature, time, and catalyst loading amount) on the lignin depolymerization were investigated. Overall, the highest bio-oil yield of 72% and the 3.5 times higher yield of phenolic monomers than that without a catalyst were successfully achieved at 350 ℃ and 10% catalyst loading after 4 h reaction time.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.235-240
• /
• 2014

In this study, the torrefaction of food waste was conducted to characterize its product, to find out effect of the operating temperature and to assess the feasibility of being used as fuel. The operating temperature was varid from $180^{\circ}C{\sim}270^{\circ}C$ and heat was provided by using nitrogen gas or waste oil heat carrier. The solid yield and moisture content were reduced were reduced as temperature increased. The moisture content reduction and thermochemical conversion were observed at higher than $240^{\circ}C$. At low operating temperature, heat transfer efficiency was higher with wast oil heat carrier. As temperature increases, there was not difference in heat transfer efficiency of two different heating methods. The lower heating value product was increased from 660 to 6,400 Kcal/kg with nitrogen gas and 6,890 Kcal/kg with waste oil heat carrier. The elemental analysis indicates that, as temperature increases, the carbon content of product increases and oxygen content decreases. From the analysis of O/C and H/C, the torrefaction product was close to low grade coal. The characteristics of fuel converted from the food subsequent thermochemical treatment.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.111-116
• /
• 2001

Waste office paper, photocopied or laser printed, has recently increased along with office automatization. In waste office paper, toner ink is used as the printing medium in place of conventional oil ink. Since toner ink cannot be saponificated by alkali and be decolored by bleaching, different from the case of oil ink, toner remains on regenerated paper as black specks. Although cascade recycling of waste office paper is compelled at present, the demand for low-grade paper is limited. From such circumstances, a new separation process for waste office paper is demanded to achieve parallel recycling. At the first stage of separation studies, the sharpness of separation is evaluated using small separators to obtain fundamental data. In a lab-scale separator, the sample amount of one feed is generally a few grams. However, the sample amount used for brightness, ERIC, and image analysis that are generally used to evaluate the efficiency of deinking are not small for lab-scale tests of these analyses. This paper describes an investigation of a sheet preparation method by a small amount of sample under 0.5g and compares the precision of toner content determination of spectroscopic analysis and image analysis from the viewpoint of separation evaluation. The easiness and convenience of the operation using only general-purpose equipments has also been set as a principle purpose. From the viewpoint of an analysis that yields high precision with a small amount of sample in short time, the method calculating the absorption coefficient from diffuse reflectance in the visible region is the most rational method in this study.

• Journal of Microbiology and Biotechnology
• /
• v.33 no.11
• /
• pp.1531-1541
• /
• 2023

Lipase is a well-known and highly in-demand enzyme. During the last decade, several lipase optimization studies have been reported. However, production costs have always been a bottleneck for commercial-scale microbial enzyme production. This research aimed to optimize the conditions for lipase production by Limtongozyma siamensis DMKU-WBL1-3 via a One-Factor-At-a-Time (OFAT) approach combined with statistical methods while using a low-cost substrate. Results suggest that low-cost substrates can be substituted for all media components. An optimal medium was found, using response surface methodology (RSM) and central composite design (CCD), to consist of 0.50% (w/v) sweet whey, 0.40% (w/v) yeast extract (food grade), and 2.50% (v/v) palm oil with the medium pH adjusted to 4 under shaking flask cultivation. From an economic point of view, this work was successful in reducing production costs while increasing lipase productivity. The medium costs were reduced by 87.5% of the original cost while lipase activity was increased by nearly 6-fold. Moreover, lipase production was further studied in a 2-L stirred-tank fermentor. Its activity was 1,055.6 ± 0.0 U/ml when aeration and agitation rates were adjusted to 1 vvm and 170 rpm, respectively. Interestingly, under this optimal lipase production, the yeast showed accumulated lipids inside the cells. The primary fatty acid is a monounsaturated fatty acid (MUFA) that is typically linked to health benefits. This study hence reveals promising lipase production and lipid accumulation by L. siamensis DMKU-WBL1-3 that are worthy of further study.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.116.1-116.1
• /
• 2010

저급 연료원인 오일샌드는 아스팔트와 같은 중질유를 10% 이상 함유한 모래 또는 사암으로서, 겉으로는 시커먼 흙이나 모래처럼 보이나 내부에는 bitumen, 모래(점토) 및 물 등이 광물질 70~80%, bitumen 10~18%, 물 3~5% 정도의 비율로 혼합되어 있는데, 가열 또는 용매 추출 방식으로 오일샌드에 포함되어 있는 bitumen을 분리하여 정제하면 원유를 생산할 수 있으므로 고유가 시대의 대체에너지원으로 세계적인 석유회사들이 개발을 진행하고 있다. 따라서, 본 연구에서는 이러한 저급 연료원인 오일샌드 bitumen의 활용기술 개발을 위하여 기초특성 분석 결과 bitumen과 가장 유사한 특성을 가지는 것으로 파악된 중질잔사유를 대상으로 가스화를 통한 액체연료 전환을 위해 고점도 시료공급장치, 가스화기, 집진장치, 탈황장치, 수성가스 전환장치, 합성가스 압축장치, DME 전환장치 등으로 구성되는 시스템을 구축한 후 시험을 진행하였다.

• Journal of the Korean Society of Safety
• /
• v.23 no.1
• /
• pp.1-11
• /
• 2008

In this study, small punch test and tensile test were performed with specimens directly machined from an ASTM A53 grade B carbon steel pipe at which an explosion accident was occurred in the Heavy Oil Unit. Main damage mechanism of the pipe was known as a high temperature hydrogen attack(HTHA). Effects of HTHA on the mechanical strength change of the A53B steel were studied in detail. Small punch test results have showed that maximum reaction forces, SP energy and ductility were decreased at hydrogen attacked part of the pipe compared with sound part of the pipe. Yield strength and tensile ultimate strength were calculated with the obtained small punch test curve results using different methods and compared the estimation methods. Small punch test simulation has been also performed with the finite element method and then mechanical strength, equivalent strain and fracture toughness were calculated with the obtained numerical analysis results. It was shown that the fracture toughness data calculated from small punch equivalent energy obtained by the finite element analysis for SP test was very low at the hydrogen attacked part.