• Journal of the Korea Society of Computer and Information
• /
• v.3 no.2
• /
• pp.77-84
• /
• 1998

The continuous time signal system by development of CMOS technology have been receiving consideration attention. In this paper, Low pass filter using CMOS floating resistor have been designed with cut off frequency for speech signal processing. Especially a new floating resistor consisting entirely of CMOS devices in saturation has been developed. Linearity within $\pm$0.04% is achieved through nonlineartiy via current mirrors over an applied range of $\pm$1V. The frequency response exceeds 10MHz, and the resistors are expected to be useful in implementing integrated circuit active RC filters. The low pass filter designed using this method has simpler structure than switched capacitor filter. So reduce the chip area. The characteristics of the designed low pass filter using this method are simulated by pspice program.

• Journal of the Korea Society for Simulation
• /
• v.10 no.4
• /
• pp.21-30
• /
• 2001

In this paper, EMI measurement, the STGU simulation being conducted, filter design, its characteristics, and its implementation to the PCB, and finally test results are discussed. When the low pass filter was implemented within the STGU, the power of EMI decreased more than 20dBm. Finally, when TE and MTIE, two important quality measure in synchronous reference clock, was assessed, ITU-T G813 requirement was satisfied. EMI(Electromagnetic Interface) is a measure of electomagnetic radiation from equipment in the range of 10KHz to 3GHz, and can cause unexpected reactions of electronics/electrical equipment. In this study, for safe and stable communication operation, a STGU (System Timing Generation Unit), which is a 2.5G SDH System and a major EMI source, was employed to simulate electromagnetic interface. Using Open-Site test, the power of fundamental frequency of EMI of interest and its harmonics were measured. Also, a low pass filter at cut-off frequency of 2GHz was specifically designed for this study to minimize the effect of EMI between electronic components.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.357-360
• /
• 1999

A 20 MHz CMOS continuous low-pass filter using simulated floating inductor consisted of two fully-differential transconductors and a capacitor is presented. The theory of operation is described and simulation results show close agreement between predicted behaviour and experimential performance. Simulation results show that the filter has ripple bandwidth of 22 MHz, pass-band ripple of 0.36 ㏈. and cutoff frequency of 26 MHz at supplay voltage of $\pm$3 V. The power dissipation is 19.2 ㎽.

• Journal of Industrial Technology
• /
• v.14
• /
• pp.3-17
• /
• 1994

This paper develops a design technique for approximating nonseparable frequency characteristics by sums and products of separable transfer functions. Therefore nonseparable frequency characteristics includes the four-quadrant symmetry filters. The desired filter with half plan symmetry is obtained by shifting a low pass characteristic in the frequency domain, and by combining these shifted characteristics. Also the paper develops the technique for designing recursive and nonrecursive two dimensional digital filters by the application of a complex transformation to one dimensional low pass filter.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.36-40
• /
• 2013

A novel design method of ultra wideband bandpass filter using CRLH transmission line with Dumbell type DGS is presented in this paper. Defected Ground Structure and microstrip interdigital capacitor are used to design the ultra wideband (UWB) filter. CRLH transmission line has composite characteristics of low pass and high pass filter. As control of cutoff frequency of low pass and high pass response on CRLH transmission line, we can get characteristic of UWB filter. We designed and simulated for CRLH transmission lines with one, two, four, and eight cells. A UWB filter using four cells CRLH is designed and fabricated to verify the results. The characteristics of designed filter have center frequency of 5GHz and relative bandwidth of 88%.

• Journal of Advanced Navigation Technology
• /
• v.13 no.1
• /
• pp.41-47
• /
• 2009

In this paper, a band pass filter with a rejection band is proposed for UWB(Ultra Wide Band) communication system. First, low pass filter accessed cut off frequency of 10.2 GHz was designed using structure stepped impedance. And high pass filter accessed cut of frequency of 3.2 GHz was designed using parallel short-stub. There was implemented composite connection of designed low pass filter and high pass filter. The relative dielectric constant, the height, the loss tangent of the PCB substrate were ${\varepsilon}_r$=2.2, h=0.508 mm and loss tangent = 0.0009 respectively. The fabricated band pass filter shows a compact size of 3 cm. The fabricated band pass filter was characterized using 37169A VNA(Vector Network Analyzer). And measured result were obtained 7.5 GHz of bandwidth and -10 dB of return loss and -3 dB of insertion loss from pass band. The result of the research can be used for the UWB communications and MIC/MMIC, RFIC system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.5
• /
• pp.388-392
• /
• 2012

In this paper, a sampler model for the P-type current mode control employing low pass filter is proposed. Even though the frequency response of the compensator used in a P-type current mode control employing low pass filter is similar to that of P-type compensator, the sampler model has to be obtained from the method used in PI-type current mode control. In order to show the usefulness of the proposed method, prediction results of the proposed model are compared to those from the circuit level simulator, PSIM.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.4
• /
• pp.257-262
• /
• 2015

In this paper, the split-ring DGS resonator is proposed and its equivalent circuit are analyzed to design the low pass filter. Compared with the conventional dumbell DGS cell, this structure has a flat fluctuation in low frequency range and a sharp slop at edge frequency. The out-band suppression of the SRR-DGS cell can be improved by placing the open stubs on the conductor line which operates as parallel capacitances. Making use of equivalent circuit analytical method, the characteristics of the improved SRR DGS cell are investigated and applied to design compact low pass filter, which has a low in-band loss, sharp slop and high suppression of more than 35dB within a wide out-band frequency range. The dependence of the transmission characteristic on the dimension of a split ring, such as side-length and split-gap, is analyzed in detail. In addition, an improved SRR DGS cell model with open stubs loaded on the conductor line is then presented to improve the out-band suppression. By using the equivalent-circuit analytical method, an S-band microstrip low-pass filter with perfect low-pass characteristic and high out-band suppression is designed and fabricated.

• Current Optics and Photonics
• /
• v.7 no.4
• /
• pp.345-353
• /
• 2023

We propose a turbulence-tolerant Manchester on-off keying (M-OOK) transmission for free-space optical (FSO) communication. At the transmitter end, a M-OOK signal featuring a spectrum with low-frequency components absent is modulated and transmitted into a turbulent channel. At the receiver end, a low-pass filter (LPF) -based adaptive-threshold decision (ATD) with LPF-extracted channel-state information (CSI) and a high-pass filter (HPF)-based fixed-threshold decision (FTD) are employed to compensate for the effects of turbulence, owing to the low-frequency spectral characteristics of the turbulent channel. The performance of LPF-based ATD and HPF-based FTD are evaluated for various cutoff frequencies for the LPF and HPF. Besides, the proposed M-OOK transmission is compared to conventional non-return-to-zero OOK (NRZ-OOK) for different data rates. The proposed technique is verified in simulation. The simulation results show that the proposed M-OOK detection with optimized cutoff frequencies of LPF and HPF has better bit-error-rate (BER) performance compared to NRZ-OOK, and it is close to the theoretical ATD with the knowledge of precise CSI under various degrees of turbulence effects.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.11
• /
• pp.1053-1059
• /
• 2007

This paper presents a target sate estimator(TSE) with low pass filter for improving the gun driving command. The ballistic computer uses target information such as predicted range, velocity, acceleration of a target to generate the gun command. We adopt the finite impulse response(FIR) filter as our TSE to shorten calculation time for the driving command and due to its inherent stability property. We also introduce a post-processing filter to reduce the high frequency components in the output signal of a TSE which may cause instability of gun driving. The first order low pass filter has been designed based on $H{\infty}$ criteria considering the noise characteristics. To show the validity of the present scheme, simulation results are given for the overall gun driving system including aircraft target information.