• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.354-359
• /
• 2011

Silicon nitride ceramics were prepared by microwave gas phase reaction sintering. By this method higher density specimens were obtained for short time and at low temperature, compared than ones by conventional pressureless sintering, even though sintering behaviors showed same trend, the relative density of sintered body inverse-exponentially increases with sintering temperature and/or holding time. And grain size of ${\beta}$-phase of the microwave sintered body is bigger than one of the conventional pressureless sintered one. Also they showed good bending strengths and thermal shock resistances.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.136-141
• /
• 2005

In this study, in order to develop the low temperature sintering ceramics for multilayer piezoelectric transformer, PCW-PMN-PZT ceramics using Li$_2$CO$_3$, Bi$_2$O$_3$, and CuO as sintering aids were manufactured according to the amount of MnO$_2$ addition. Their microstructural, dielectric and piezoelectric properties were investigated. When the sintering aids were added, specimens could be sintered below 95$0^{\circ}C$, but mechanical qualify factor decreased. Therefore, MnO$_2$ was added excessively to the PCW-PMN-PZT ceramics to increase mechanical quality factor. At the sintering temperature of 95$0^{\circ}C$, the density, dielectric constant($\varepsilon$$_{r}$), electromechanical coupling factor(k$_{p}$), mechanical quality factor(Q$_{m}$) and Curie temperature(T$_{c}$) of 0.1 wt% MnO$_2$ added specimen showed the optimal values of 7.75 g/㎤, 1503, 0.57, 1502, and 337, respectively, for multilayer piezoelectric transformer application.ation.n.

• Nuclear Engineering and Technology
• /
• v.52 no.1
• /
• pp.115-122
• /
• 2020

A promising method for removal of Cs ions from water and their incorporation into stable crystal structure ready for safe and permanent disposal was described. Cs-exchanged X zeolite was hot-pressed at temperature ranging from 800 to 950 ℃ to fabricate dense pollucite ceramics. It was found that the application of external pressure reduced the pollucite formation temperature. The effect of sintering temperature on density, phase composition and mechanical properties was investigated. The highest density of 92.5 %TD and the highest compressive strength of 79 MPa were measured in pollucite hot-pressed at 950 ℃ for 3 h. Heterogeneity of samples obtained at 950 ℃ was determined using scanning electron microscopy. The pollucite hot-pressed at 950 ℃ had low linear thermal expansion coefficient of ~4.67 × 10^-6 K^-1 in the temperature range from 100 to 1000 ℃.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.1
• /
• pp.31-34
• /
• 2007

In this study, in order to develop multilayer ceramics vibrator for ultrasonic nozzle, PMN-PNN-PZT ceramics were fabricated using $Li_{2}CO_{3}-Na_{2}_CO_{3}$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the amount of PbO. With increasing PbO contents, secondary phases were increased and phase structure was changed from tetragonal structure to rhombohedral structure and also electromechanical coupling factor was linearly decreased. At the composition ceramics with the sintering temperature of $870^{\circ}C$ and 1 mol% excess PbO, density, electromechanical coupling factor, dielectric constant, piezoelectric d constant and mechanical quality factor showed the optimum value of $7.879\;g/cm^{3}$, 0.55, 1149, 328 pC/N, 1224, respectively for multilayer ceramics vibrator application for ultrasonic nozzle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.10
• /
• pp.615-619
• /
• 2015

In this study, in order to develop the composition ceramics with the excellent electrocaloric properties, 8/65/35 PLZT ceramics were fabricated by the conventional solid-state method with the addition of $Bi_2O_3$, CuO, $Li_2CO_3$ and the variation of sintering temperature from $930^{\circ}C$ to $990^{\circ}C$. The XRD pattern of all specimens indicated general perovskite structure and the rhombohedral phase were observed. Curie temperature ($T_c$) of all specimens was observed in the vicinity of about $190^{\circ}C$. Density, coercive field and remnant polarization of the specimen sintered at $950^{\circ}C$ was $7.55g/cm^3$, 8.895 kV/cm, $11.22{\mu}C/cm^2$, respectively. EC effect of PLZT ceramics was measured by indirect method and the temperature change ${\Delta}T$ due to the electrocaloric effect was calculated by Maxwell's relations. ${\Delta}T$ of ceramic sintered at $950^{\circ}C$ was $0.21^{\circ}C$ under application of 40 kV/cm at $190^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.51-56
• /
• 1999

The $BaTiO_3$ powders were synthesized by GNP (Glycine-Nitrate process). The powders were prepared using carbonate and alkoxide as starting materials and nitric acid was used as a solvent for starting materials as well as an oxidant for combustion. the effects of aggregates in $BaTiO_3$ powders on green densities, sintering and dielectric characteristics were investigated. When the glycine/cation molar ratio was 1.2, reactivity of self-combustion was most intensive and the degree of aggregates after calcination was low. On sintering at $1400^{\circ}C$, maximum theoretical relative density(94.99%%0 was obtained in case of 1.2 molar ratio of glycine/cation. The dielectric constant of this sintered $BaTiO_3$ was 1919.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.575-582
• /
• 1998

Sutiability of Jungsan clay shale dolomite sludge Anyang feldspar and alumina as raw materials for light-weight porous ceramics was examined. In order to find optimum manufacturing conditions compositions heating temperatuers and heating times were varied and their effects on physical properties were measured and bloating mechanism was investigated. Jungsan clay seems suitable as raw material to make the light-weight constructional materials with 5wt% of ANyang feldspar and alumina added in calcined clay (800$^{\circ}C$) having bulk density of 0.45g/cm3 water absorption of 1.34% and compressive strength of 85kg/cm2 rapid-heated at 1200$^{\circ}C$ for 30min. It is suggested that bloating mechanism depends on the difference of tem-peratures between the inside and outside in specimen the remained gases in interstices can bloat by the li-quid phase of surface with high viscosity and gas pressure at elevated temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.439-442
• /
• 2004

The effects of sintering additives on the low-temperature sintering and microwave dielectric properties of $Mg_4Nb_2O_9$ dielectric ceramics were studied. When $3{\sim}20wt%$ of $0.242Bi_2O_3-0.758V_2O_5$ was added, the sintering temperature decreased from $1100{\sim}1300^{\circ}C$ to $950^{\circ}C$ and high density was obtained. When $Mg_4Nb_2O_9$ was sintered at $950^{\circ}C$ with 10wt% of sintering additive, the microwave dielectric properties of $Q{\times}f_0\;=\;80.035GHz,\;\epsilon_r\;=\;13.3\;and\;\tau_f\;=\;-12.9\;ppm/^{\circ}C$ were obtained.

• Journal of the Korean Ceramic Society
• /
• v.26 no.6
• /
• pp.843-849
• /
• 1989

Effect of Bi2O3/Li2CO3 on low temperature sinteirng and dielectric property of BaTiO3 ceramics has been investigated. For the specimen sintered at 110$0^{\circ}C$, it was densified to 96% of BaTiO3 theoretical density by the addition of 1.0-1.25w/o Bi2O3/Li2CO3. Maximum dielectric constant increased and Curie temperature lowered with the increase of Bi2O3/Li2CO3 content, which probably can be explained by thne substitution of Bi3+, Li1+ on BaTiO3 lattice. The volatilization of Li1+, resulting from the increase of soaking time at 110$0^{\circ}C$ leads to the increase of Curie temperature and tetragonality of the specimen.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.601-610
• /
• 1997

In cofiring of multilayered alumina with tungsten, the change of camber with lamination condition was experimented and the effect of sintering shrinkage of alumina and tungsten was investigated. From the exact measurement of sintering shrinkage of tungsten thick film, as lamination pressure increased, the sintering shrinkage of alumina decreased but that of tungsten thick film was not changed. So it was though that the main factor which induced the sintering shrinkage difference between ceramics and metal with lamination condition was the change of sintering shrinkage of ceramics. In case of high lamination pressure, high green sheet density, the cofired specimen showed low camber due to low shrinkage difference between alumina and tungsten and there was a linear relation between camber and shrinkage difference. It was found that this shrinkage difference could change the thickness of tungsten film and the microstructure within via hole during cofiring.