• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.20-26
• /
• 2008

Nanoimprint lithography(NIL) is becoming next generation lithography of significant interest due to its low cost and a potential patterning resolution of 10nm or less. Success of the NIL relies on the adequate conditions of pressure, temperature and time. To have the adequate conditions for NIL, one has to understand the polymer flowing behavior during the imprinting process. In this paper, an analytical approach of polymer flow in thermal NIL was performed based on the squeeze flow with partial slip boundary conditions. Velocity profiles and pressure distributions of the polymer flow were obtained and imprinting forces and residual thickness were predicted with the consideration of the slip velocity between the polymer and the mold/substrate. The results show that the consideration of the slip is very important for investigating the polymer flow in Thermal NIL.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.76-81
• /
• 2008

Nanoimprint lithography(NIL) is an emerging technology enabling cost-effective and high-throughput nanofabrication. Among NILs, significant efforts from both academia and industry have been put in UV NIL research and development because of its ability to pattern at room temperature and at low pressure. In UV NIL, there may be in-line set-up error of the stamp and the substrate. To compensate this error, the dummy blocks are put on the stamp and pressurized uniformly. Contact problems between the stamp and the photoresist layer on the substrate are often happened, which results in the non-uniform residual layer In this paper, the pressurization method on the dummy block is investigated by the finite element method. A new method is recommended and evaluated far the uniform stamp deformation.

• 소성∙가공
• /
• 제18권3호
• /
• pp.268-273
• /
• 2009

Ultraviolet nanoimprint lithography (UV-NIL), which is performed at a low pressure and at room temperature, is known as a low cost method for the fabrication of nano-scale patterns. In the patterning process, maintaining the uniformity of the residual layer is critical as the pattern transfer of features to the substrate must include the timed etch of the residual layer prior to the etching of the transfer layer. In pursuit of a thin and uniform residual layer thickness, the initial volume and the position of each droplet both need to be optimized. However, the monomer mixtures of resin had a tendency to evaporate. The evaporation rate depends on not only time, but also the initial volume of the monomer droplet. In order to decide the initial volume of each droplet, the accurate prediction of evaporation behavior is required. In this study, the theoretical model of the evaporation behavior of resin droplets was developed and compared with the available experimental data in the literature. It is confirmed that the evaporation rate of a droplet is not proportional to the area of its free surface, but to the length of its contact line. Finally, the parameter of the developed theoretical model was calculated by curve fitting to decide the initial volume of resin droplets.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.199-204
• /
• 2007

Hot embossing, one of Nanoimprint Lithography(NIL) techniques, has been getting attention as an alternative candidate of next generation patterning technologies by the advantages of simplicity and low cost compared to conventional photolithographies. A typical hot embossing usually, however, takes more than ten minutes for one cycle of the process because of a long thermal cycling. Over the last few years a number of studies have been made to reduce the cycle time for hot embossing or similar patterning processes. The target of this research is to develop an induction heating apparatus for heating a metallic micro patterning mold at very high speed with the large-area uniformity of temperature distribution. It was found that a 0.5 mm-thick nickel mold can be heated from $25^{\circ}C$ to $150^{\circ}C$ within 1.5 seconds with the temperature variation of ${\pm}5^{\circ}C$ in 4-inch diameter area, using the induction heating apparatus.

• 반도체디스플레이기술학회지
• /
• 제11권4호
• /
• pp.37-42
• /
• 2012

Nanoimprint lithography (NIL) has attracted broad interest as a low cost method to define nanometer scale patterns in recent years. A major disadvantage of thermal NIL is the thermal cycle, that is, heating over glass transition temperature and then cooling below it, which requires a significant amount of processing time and limits the throughput. One of the methods to overcome this disadvantage is to improve the cooling performance in NIL process. In this paper, the performance of the cooling system of thermal NIL is numerically investigated by SolidWorks Flow Simulation program. The calculated temperatures of nanoimprint device were verified by the measurements. By using the analysis model, the effects of the change of flow velocity and cooler location on the cooling performance are investigated. For the 6 cases (0.1 m/s, 0.5 m/s, 1 m/s, 3 m/s, 5 m/s, 10 m/s) of flow velocity and for the 6 cases of distances (50 mm, 40 mm, 30 mm, 20 mm, 10 mm, 1 mm) of cooler location, the heat conjugated flow analyses are performed and discussed.

• 소성∙가공
• /
• 제16권4호
• /
• pp.282-287
• /
• 2007

Hot embossing, one of Nanoimprint Lithography(NIL) techniques, has been getting attention as an alternative candidate of next generation patterning technologies by the advantages of simplicity and low cost compared to conventional photolithographies. A typical hot embossing usually, however, takes more than ten minutes for one cycle of the process because of a long thermal cycling. Over the last few years a number of studies have been made to reduce the cycle time for hot embossing or similar patterning processes. The target of this research is to develop an induction heating apparatus for heating a metallic micro patterning mold at very high speed with the large-area uniformity of temperature distribution. It was found that a 0.5 mm-thick nickel mold can be heated from $25^{\circ}C\;to\;150^{\circ}C$ within 1.5 seconds with the temperature variation of ${\pm}5^{\circ}C$ in 4-inch diameter area, using the induction heating apparatus.

• 한국재료학회지
• /
• 제17권1호
• /
• pp.31-36
• /
• 2007

Nanoimprint lithography (NIL) is a new lithographic method that offers a sub-10nm feature size, high throughput, and low cost. One of the most serious problems of NIL is the stiction between mold and resist. The antistiction layer coating is very effective to prevent this stiction and ensure the successful NIL results. In this paper, an antistiction layer was deposited by VSAM (vapor self assembly monolayer) method on silicon samples with FOTS (perfluoroctyltrichlorosilane) as a precursor for making an antistiction layer. A specially designed LPCVD (low pressure chemical vapor deposition) was used for this experiment. All experiments were achieved after removing the humidity. First, the evaporation test of FOTS was performed for checking the evaporation temperature at low pressure. FOTS was evaporated at 5 Tow and $110^{\circ}C$. In order to evaluate the temperature effect on antistiction layer, chamber temperature was changed from 50 to $170^{\circ}C$ with 0.1ml of FOTS for 1 minute. Good hydrophobicity of all samples was shown at about $110^{\circ}$ of contact angle and under $20^{\circ}$ of hysteresis. The surface energies of all samples calculated by Lewis acid/base theory was shown to be about 15mN/m. The deposited thicknesses of all samples measured by ellipsometry were almost 1nm that was similar value of the calculated molecular length. The surface roughness of all samples was not changed after deposition but the friction force showed relatively high values and deviations deposited at under $110^{\circ}$. Also the white circles were founded in LFM images under $110^{\circ}$. High friction forces were guessed based on this irregular deposition. The optimized VSAM process for FOTS was achieved at $170^{\circ}C$, 5 Torr for 1 hour. The hot embossing process with 4 inch Si mold was successfully achieved after VSAM deposition.

• KSBB Journal
• /
• 제22권6호
• /
• pp.433-437
• /
• 2007

본 연구에서는 나노임프린트 리소그래피를 이용하여 500 nm line, 600 nm pore, $1{\mu}m$ pore, $2.5{\mu}m$ pore의 마이크로 수준에서 나노 수준에 이르는 다양한 크기와 모양의 nanopore 형태 패턴을 제작하였다. Thermal imprint 방식과 달리 상온, 저압에서 임프린팅이 가능하며 사용되는 스탬프의 수명을 늘리고 보다 미세하고 복잡한 형태의 패턴을 제작할 수 있는 UV-assisted imprint 방식을 사용하였다. E-beam lithography로 패턴을 각인한 quartz소재의 스탬프를 사용하였으며 스탬프의 재질이 투명하여 UV 조사시 UV curable resin이 경화될 수 있도록 하였다. 또한 스탬프의 표면을 (heptadecafluoro-1,1,2,2-tetrahydrodecyl) trichlorosilane의 monolayer 층으로 미리 코팅하여 임프린트 후 스탬프와 기판과의 releasing을 쉽게함과 동시에 패턴의 일부가 스탬프에 묻어 나와 전사된 패턴에 defect가 없도록 하였다. 또한, gold를 미리 증착하여 임프린팅함으로써 lift-off 시에 필요한 hi-layer 층이 필요 없게 되어 산소 플라즈마를 이용한 에칭이 더욱 쉽고 lift-off 공정이 생략될 수 있도록 하였다. 나노임프린트 공정에 있어 가장 큰 문제점은 잔여층의 생성이며 이러한 잔여층을 제거하고자 산소 플라즈마 에칭을 하였다. 에칭공정을 통해 gold의 표면이 완전히 드러났으며 산소 플라즈마를 통해 gold의 표면이 친수성으로 바뀌어 추후 단백질 고정화를 더욱 쉽게 하였다. 그리하여 나노임프린트 기술을 이용해 나노크기의 바이오소자 제작을 가능하게 하였다.

• 마이크로전자및패키징학회지
• /
• 제30권2호
• /
• pp.65-70
• /
• 2023

나노임프린트 리소그래피(Nanoimprint lithography, NIL) 공정은 패턴 형성을 위한 공정 단순성, 우수한 패턴 형성, 공정의 확장성, 높은 생산성 및 저렴한 공정 비용이라는 이유들로 인해 많은 관심을 받고 있다. 그러나, 기존의 NIL 기술들을 통해 금속 소재 상 구현할 수 있는 패턴의 크기는 일반적으로 마이크로 수준으로 제한적이다. 본 연구에서는, 다양한 두께의 금속 기판 표면에 마이크로/나노 스케일 패턴을 직접적으로 형성하기 위한 극압 임프린트 리소그래피(extremepressure imprint lithography, EPIL) 방법을 소개하고자 한다. EPIL 공정은 자외선, 레이저, 임프린트 레지스트 또는 전기적 펄스 등의 외부 요인을 사용하지 않고 고분자, 금속, 세라믹과 같은 다양한 재료의 표면에 신뢰성 있는 나노 수준의 패터닝을 가능하게 한다. 레이저 미세가공 및 포토리소그래피로 제작된 마이크로/나노 몰드는 상온에서 높은 하중 혹은 압력을 가해 정밀한 소성변형 기반 Al 기판의 나노 패터닝에 활용된다. 20 ㎛ 부터 100 ㎛까지 다양한 두께를 갖는 Al 기판 상 마이크로/나노 스케일의 패턴 형성을 보여주고자 한다. 또한, 다목적 EPIL 기술을 통해 금속 재료 표면에서 그 형상을 제어하는 방법 역시 실험적으로 증명된다. 임프린트 리소그래피 기반 본 접근법은 복잡한 형상이 포함된 금속 재료의 표면을 요구하는 다양한 소자 응용을 위한 나노 제조 방법에 적용될 수 있을 것으로 기대한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1917-1921
• /
• 2008

Ultraviolet-nanoimprint lithography (UV-NIL) is promising technology for cost effectively defining micro/nano scale structure at room temperature and low pressure. In addition, this technology is fascinating because of it's possibility for high-throughput patterning without complex processes. However, to acquire good micro/nano patterns using this technology, there are some challenges such as uniformity and fidelity of patterns, etc. In this paper, we have focused on uniform contact mechanism and performed contact mechanics analysis. The dimension of the flexible sheet to get adequate uniform contact area has been obtained from contact mechanics simulation. Based on this analysis, we have made a uniform pressurizing device and confirmed its uniform pressurized zone using a pressure sensing paper.