• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2007년도 학술대회
• /
• pp.279-282
• /
• 2007

Typically a wireless sensor network consists of a number of nodes that sense surrounding environment and collaboratively work to process and route the sensing data to a sink or gateway node. We propose an architecture with support of multiple routers in IPv6-based Low-power Wireless Personal Area Network (6LoWPAN). Our architecture provides traffic load balancing and increases network lifetime as well as self-healing mechanism so that in case of a router failure the network still can remain operational. Each router sends its own Router Advertisement message to nodes and all the nodes receiving the messages can select which router is the best router with the minimum hop-count and link information. We have implemented the architecture and assert our architecture helps in traffic load balancing and reducing data transmission delay for 6LoWPAN.

• Journal of Advanced Navigation Technology
• /
• 제24권2호
• /
• pp.61-66
• /
• 2020

Since the ocean accounts for 70.8 percent of the earth's surface, the success of IoT technology in the marine industry is to collect information from devices placed in a wider range. LPWA is a feature with a wide range of communication and is very suitable for deployment in the ocean. In this paper, the real-sea performance distance experiment was carried out based on Private LoRa, a key technology for executing the electronic phrase real-name system. A private LoRa module based on sx1276 was developed, and Gateway was developed to transfer data received by private LoRa to the server using SKT Cat. M1. After installing gateways at 599 meters above sea level and experimenting with data transmission and reception at 25 km, 40 km and 60 km, we were able to see that the communication success rate was obtained to be 96.1%. 97.1% and 96.2% respectively.

• Journal of the Korea Society for Simulation
• /
• 제17권4호
• /
• pp.191-198
• /
• 2008

6LoWPAN (IPv6 Low-power Wireless Personal Area Network) is IPv6 packets transmission technology at Sensor network over the IEEE 802.15.4 Standard MAC and Physical layer. Adaptation layer between IP layer and MAC layer performs fragmentation and reassembly of packet for transmit IPv6 packets. RFC4944, IETF 6LoWPAN WG standard document define packet fragmentation and reassembly. In this paper, we propose the 6PASim (6LoWPAN Packet Simulator) to perform IPv6 packet fragmentation and reassembly for performance evaluation. The 6PASim consist of two parts. One is Packet_Transmit_module that makes IEEE 802.15.4 frames the IPv6 packet from upper layer, and transmit its. and the another is Packet_Receive_module that reassembles transferred frames and completes original IPv6 packets. we can evaluate frame transmit rate and amount of control message through 6PASim. The result of simulation shows the SRM (Selective Retransmission Method) scheme provider better performance than IRM (Immediate Retransmission Method) scheme.

• Proceedings of the Korea Information Processing Society Conference
• /
• 한국정보처리학회 2016년도 추계학술발표대회
• /
• pp.816-818
• /
• 2016

LPWA 기술은 IoT 환경이 가지는 낮은 전송거리와 배터리 제약을 해결할 수 있는 통신규약이다. LPWA에서 주목 받는 LoRa 기술은 디바이스에서 전송방식을 선택할 수 있는 클래스 A, B, C를 제공한다. 이 논문은 클래스 B 옵션에서 동기는 맞으나 전송 중 Beacon메시지를 분실하였을 경우, 바로 실행되던 Beacon-less동작을 억제하도록 최대 실패 횟수를 설정한다. 기존방법보다 Beacon-less동작이 기존 방법에 비해 30배 이상 적게 동작하여 디바이스의 에너지 소모를 줄였다.

• IEMEK Journal of Embedded Systems and Applications
• /
• 제13권3호
• /
• pp.133-141
• /
• 2018

There are increasing interests on smart home systems. However, most of the existing works focus on the functionality itself. In this paper, we propose an extensible smart home system based on low power networking such as CoAP, 6LoWPAN, and Zigbee. The proposed home IoT system consists of Home APP, Home Server, Home Broker, and Power Devices. Each component of the system is connected by the low-power network technologies aforementioned. As the end device, Power Device senses the current consumption of the attached appliance and controls the power to it. Power Device reports the sensing data to Home Server via Home Broker. The Home Broker enhances the scalability of the system. Home Broker extends the service area and the user's services, and it manages the connection of the underlying devices and processes, and transmits data to Home Server from Power Devices. Through the experimental evaluation, we show that the proposed system achieves the design goals such as extensibility and low power networking.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제33권1호
• /
• pp.55-61
• /
• 2020

Social infrastructure facilities that have been under construction since the country's high-growth period are undergoing rapid aging, and, thus, safety assessments of large structures such as bridge tunnels, which can be directly linked to large-scale casualties in the event of an accident, are necessary. It is difficult to construct economical and efficient wireless smart sensor networks that improve structural health monitoring (SHM) because the existing wire sensors have a short signal reach. However, low-power wide-area networks (LPWANs) are becoming popular within the Internet of Things, and enable economical and efficient SHM. In this study, the technology trends of a wireless measuring sensor based on LoRa LPWANs were investigated, and an installation and maintenance plan for this type of sensor is proposed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 한국정보통신학회 2016년도 추계학술대회
• /
• pp.285-289
• /
• 2016

In recent domestic new growth model based on the IoT it has been proposed by the industry and national authorities. As applied to these Internet-based IoT convergence center of the field is expected to be realized, including the improvement and increase of efficiency of various economic values. In this paper, using KETI ( Korea Electronics Technology Institute ) developed distribution being oneM2M standards-based platform from Mobius and Gateway Platforms & Cube, and low power, capable of long-range RF communication LoRa communication module is proposed to build the site applicable environment.

• IEMEK Journal of Embedded Systems and Applications
• /
• 제14권2호
• /
• pp.87-96
• /
• 2019

Low power issue is one of the most critical problems in the Internet of Things (IoT), which are powered by battery. To solve this problem, various approaches have been presented so far. In this paper, we propose a method to reduce the power consumption by reducing the numbers of accesses into the flash memory consuming a large amount of power for on-chip software execution. Our approach is based on using cooperative logging structure to distribute the sampling overhead in single sensor node to adjacent nodes in case of rare-event applications. The proposed algorithm to identify event occurrence is newly introduced with negative feedback method by observing difference between past data and recent data coming from the sensor. When an event with need of flash access is determined, the proposed approach only allows access to write the sampled data in flash memory. The proposed event detection algorithm (EDA) result in 30% reduction of power consumption compared to the conventional flash write scheme for all cases of event. The sampled data from the sensor is first traced into the random access memory (RAM), and write access to the flash memory is delayed until the page buffer of the on-chip flash memory controller in the micro controller unit (MCU) is full of the numbers of the traced data, thereby reducing the frequency of accessing flash memory. This technique additionally reduces power consumption by 40% compared to flash-write all data. By sharing the sampling information via LoRa channel, the overhead in sampling data is distributed, to reduce the sampling load on each node, so that the 66% reduction of total power consumption is achieved in several IoT edge nodes by removing the sampling operation of duplicated data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제13권3호
• /
• pp.239-254
• /
• 1988

In this paper an exciter which performs modulation and amplification is composed of high power(30dBm) VCO(Voltage Controlled Oscillator) using push-pull circuit. Modulation is FSK using PLL(Phase Locked Loop). A single loop PLL synthesizer having sequency range of 42.5-100.5MHz, 25KHz channel spacing and switching time of 1msec converts down the exciter VCO frequency to 1.25MHz. This signal mixed with the FSK modulated signal coming in the phase detector of exciter. The acquisition time of exciter for frequency hoppng is less than 200usec, so the total acquisition time for transmission is less that 1.5msec. There is no need of additional power amplification because power amlifiction by high power VCO is high enough to communicate within near distance. The proposed frequency synthesizer is not complex so it is suitable for low cost slow frequency hopping spread spectrum communication.

• Journal of IKEEE
• /
• 제8권1호
• /
• pp.73-78
• /
• 2004

In this paper, it is designed for 5.8GHz Wireless LAN sub harmonic resistive mixer. Sub harmonic resistive mixer is constituted by advantage of sub harmonic mixer and resistive mixer. Sub harmonic resistive mixers mix harmonics of LO with RF and obtain IF frequency. Therefore, it was possible to use decreasing LO frequency than conventional mixers. And, Sub harmonic resistive mixer has low IMD because of using unbiased channel resistance of GaAs FET. When LO power is 13dBm, the conversion loss of manufactured sub harmonic resistive mixer is 10.67 dB. And IIP3 of mixer is 21.5dBm.