• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.89-92
• /
• 2005

Recently there have been occurred many loss of life and extensive damage to social infrastructures due to moderate and strong earthquakes all over the world. In this research, major design factors have been evaluated for the establishment of the rational seismic design code of rectangular RC bridge piers. It was concluded from this study that the axial force ratio and the longitudinal steel ratio should be the most important influencing design parameter for the seismic displacement ductility. However those parameters are not considered in the confinement steel ratio of the KHBDS. Thus, the objective of this study is to propose a rational design equation for transverse reinforcements of rectangular RC bridge piers. New confinement steel ratio is proposed by introducing the effect of the axial force and the longitudinal steel to the current KHBDS. It is thought that these new codes could release the rebar congestion problem in the plastic hinge region of RC bridge piers which contribute to the enhancement of constructibility and economization for RC bridge construction.

• 한국군사과학기술학회지
• /
• 제20권3호
• /
• pp.393-404
• /
• 2017

Side jet effect on the aerodynamic characteristics of a missile was investigated using experimental and computational methods. A couple of side jets were injected toward outward downstream at mid point of missile body. Cold air jet was used in the wind tunnel test, and cold and hot jet were used in the computation. Wind tunnel test was carried out with jet and without jet, and calculation was performed for three cases ; no jet, cold air jet, and hot mixture gas jet. From the comparison of measured and calculated data for all cases, two points could be deduced. Firstly, side jet made static stability to be unstable by increasing body normal force near the side jet exit and by decreasing tail normal force. Secondly, hot mixture gas had more significant effect on the static stability of a missile-type body than cold air jet.

• Journal of Welding and Joining
• /
• 제28권4호
• /
• pp.41-48
• /
• 2010

The purpose of this study is to establish the control method of the global bending distortion caused by fabrication process of hatch-cover in a container ship. In order to do it, the transitional behavior of global bending distortion in the deck of hatch-cover during fabrication process was measured by 3-dimensional measuring instrument. From the results, the principal factor controlling the global bending distortion was identified as the bending moment associated with the longitudinal shrinkage force and transverse shrinkage caused by welding and flame heating and the change of the centroid axis of hatch-cover in each fabrication process. Therefore, in this study, with the predictive equations of the longitudinal shrinkage force and transverse shrinkage caused by welding and flame heating and the simplified thermo elastic method, the predictive method for the global bending distortion was established and verified by comparing with the measured result. Based on the results, the amount of reverse bending distortion of main stiffeners was determined to prevent the global bending distortion of hatch-cover.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.199-203
• /
• 2004

In this paper, a simplified model is studied to predict analytically the radiated noise from the helical gear system due to an axial excitation of helical gear. The simplified model describes gear, shaft, bearing, and housing. To obtain the axial force of helical gear, mesh stiffness is calculated in the load deflection relation. The axial force is obtained from the solution of the equation of motion, using the mesh stiffness. It is used as a longitudinal excitation of the shaft, which in turn drives the gear housing through the bearing. In this study, the shaft is modeled as a rod, while the bearing is modeled as a parallel spring and damper only supporting longitudinal forces. The gear housing is modeled as a clamped circular plate with viscous damping. For the modeling of this system, transfer function from the shaft to the clamped plate are used, using a spectral method with four pole parameters. Out-of-plane displacement for the thin circular plate with viscous damping is derived and sound pressure radiated from the plate is also derived. Using the model, parameter studies are carried out.

• 한국강구조학회 논문집
• /
• 제24권1호
• /
• pp.35-46
• /
• 2012

초고층 빌딩의 수요가 증가함에 따라 고강도 강관의 수요 또한 함께 증가하고 있다. 이에 고강도 고인성의 600MPa급 강관의 접합부 내력 연구가 필요하게 되었다. 또한 현행국내기준에는 강관의 경우 항복응력 360MPa 이하에 설계식을 적용하도록 되어 있다. 즉, 고강도강재를 이용한 600MPa 강관의 경우 현행기준을 적용할 수 없으므로 600MPa급 고강도 강관의 거셋플레이트 접합부의 내력실험 및 유한요소해석을 통하여 기존 설계식의 적용가능성을 조사하고 접합부의 거동을 연구하고자 한다. 특히, 본 논문에서는 원형강관에 길이 방향으로 거셋플레이트가 접합된 접합부에 횡력(수평력)이 작용하였을 때의 거동을 다루었다. 유한요소해석 및 실험결과를 설계식과 비교해보면, 고강도 강재에서는 기존의 설계식들이 56~79%로 과소평가되었다.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.83-93
• /
• 2007

This paper represents the development of 3-axises loadcell for measuring the side-force of suspension module of MPV(Multi Purposed Vehicle). The side force causes the failure of damper, such as leakage. The loadcell was developed using strain gauges, and the Wheastone bridge circuit to compensate for the cross-talk between the each axises and the measurement error by temperature. Structure analysis of loadcell was accomplished with FEM(Finite Element Method) to optimize the location of strain gages. The design optimization for important factors that have an effect on performance of loadcell was accomplished by using DOE(Design of Experiment). Loadcell was produced and successfully tested, showing good sensitivity and low cross-talk. The cross-talk of the developed loadcell is bellow 5%. The load history was measured at proving ground. The maximum side-force, the longitudinal force, and vertical force of MPV are 4.2 kN, 8.0 kN, and 17.0 kN, respectively, at Belgian road.

• 한국산학기술학회논문지
• /
• 제17권5호
• /
• pp.173-178
• /
• 2016

콘크리트 교량 상에 고속철도의 자갈 궤도가 시공될 경우 장대 레일의 종방향 변위가 고정된 반면 교량 바닥판 슬래브의 종방향 변위가 고정되지 않고, 온도 하중과 외부 하중에 의해 교량과 레일의 상대 변위가 발생한다. 현재 장대 레일 자갈 궤도에 대한 종방향 저항력(KR C-08080, UIC code 774-3)은 교량의 종방향 변위와 자갈 궤도와 콘크리트 슬래브 사이의 마찰력을 고려하고 있지 않다. 또한 종방향 저항력 값은 다소 보수적이어서 철도교의 장경간 및 연속화에 불리한 요소로 작용하고 있다. 따라서 실제의 거동을 보다 효과적으로 반영하기 위해 장대 레일의 종저항력은 콘크리트 슬래브와 궤도 사이의 추가적인 강성을 고려해야 한다. 본 연구에서는 콘크리트 바닥판과 도상 궤도를 모사한 실대형 실험체(mock-up test specimen)를 제작하여, 교량 상에 설치된 도상 궤도의 종저항력을 측정하였고, 또한 차륜 하중의 재하 유무에 대해서도 그 거동을 평가하였다. 실험 결과, 최대 종저항력은 현재의 코드와 유사한 경향을 보였으나, 한계 변위까지의 강성은 현재의 코드보다 실험 결과가 작게 측정되는 것으로 나타났다.

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.86-91
• /
• 2012

Door effort was calculated for a new door checker with torsion bar spring and integrated checker case by FE analysis. A hybrid checker arm which has peaks and valleys only on the upper surface was adopted to reduce noise in operation and make operation with more distinctive steps. The checker arm was modeled using shell elements to estimate both the longitudinal and the lateral resistance force by checker arm. By combining the checker arm resistance force obtained from analysis and the door self-closing force by the theoretical calculation, door effort was predicted to show the good correlation with test results. In addition the unrolling effect of roller model was investigated and a new roller type for more smooth rolling was studied.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.71-78
• /
• 1998

Recently, continuous welded rail (CWR) track has been adopted for railway track structure of great advantages of reducing maintenance costs, and of increasing life time of track components and the comfort of passengers. But, in this case, a temperature or mechanical load will result in high stress and the track breakage or buckling may occur Especially when the CWR is laying on the bridge structure, the relative displacement of these structure can be increased and this results in the instability of track. In this paper, the main factors affect on the longitudinal rail force are discussed and the computer program is developed for the analysis of rail force considering the interactions with sub-structure.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.57-57
• /
• 2010

For thin panel welded structure, the various welding distortions were found due to the low resistance against welding deformation. Especially, buckling distortion induced in the thin panel welded structure produce severe problems related to cost in production stage and safety in service life. So, many researches including mechanical and thermal tensioning method for preventing the occurrence of buckling distortion in the production stage have been performed. The purpose of this study is to identify the behavior of longitudinal residual stress at the SA butt weldment with thin plate of 6mm thickness under tension load by 3 dimensional FEA. For it, mesh design for 3D FEA was constructed with 20 nodes brick element for butt weldment and 8 nodes shell element for base metal. According to FEA results, the longitudinal compressive strain inducing tensile residual stress at the butt weldment decreased. It was because the compressive thermal strain in way of weldment was reduced by tension load. The control effect of residual stress increased with an increase in tension load. So, if the amount of tension load applied to the weldment exceeds 1.5 times of longitudinal shrinkage force, the amount of longitudinal residual stress decreased below the critical value inducing the buckling distortion at the SA butt weldment. Its validity was verified by experiment.