• Clean Technology
• /
• v.20 no.2
• /
• pp.189-201
• /
• 2014

Partial oxidation, $CO_2$ reforming and the oxidative $CO_2$ reforming of $CH_4$ to produce synthesis gas over supported Ni hydrotalcite-type ($Ni_{0.5}Ca_{2.5}Al$ catalyst) catalysts were carried out and the effects of metal supports (i.e.; Mg and Ca) on the formation of a stable double-layer structure on the catalysts were evaluated. The $CH_4$ reforming stability was determined to be affected by the differences in the interaction strength between the active Ni ions and support metal ions. Only a Ni-Mg-Al composition produced a highly stable hydrotalcite-type double-layered structure; while the Ni-Ca-Al-type composition did not. Such structure provides excellent stability for the catalyst (-80% efficiency) as confirmed by the long-term $CO_2$ reforming test (-100 h), while the Ni-Ca-Al catalyst exhibited deactivation phases starting at the beginning of the reaction. The interaction strength between the active metal (Ni) and the supporting components (Mg and Al) was determined by temperature-programed reduction (TPR) analyses. The affinity was also confirmed by the TPR temperature because the Ni-Mg-Al catalyst required a higher temperature to reduce the Ni relative to the Ni-Ca-Al catalyst. The highest initial activity for synthesis gas production was observed for the $Ni_{0.5}Ca_{2.5}Al$ catalyst; however, this activity decreased quickly due to coke formation. The $Ni_{0.5}Ca_{2.5}Al$ catalyst exhibited a high reactivity and was more stable than the other catalysts because it had a higher resistance to coke formation.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.2
• /
• pp.183-202
• /
• 2019

For design and performance assessment of a high-level radioactive waste (HLW) disposal system, it is necessary to understand the characteristics of coupled thermo-hydro-mechanical (THM) behavior. However, in previous studies for the Korean Reference HLW Disposal System (KRS), thermal analysis was performed to determine the spacing of disposal tunnels and interval of disposition holes without consideration of the coupled THM behavior. Therefore, in this study, TOUGH2-MP/FLAC3D is used to conduct THM modeling for performance assessment of the Korean Reference HLW Disposal System (KRS). The peak temperature remains below the temperature limit of $100^{\circ}C$ for the whole period. A rapid rise of temperature caused by decay heat occurs in the early years, and then temperature begins to decrease as decay heat from the waste decreases. The peak temperature at the bentonite buffer is around $96.2^{\circ}C$ after about 3 years, and peak temperature at the rockmass is $68.2^{\circ}C$ after about 17 years. Saturation of the bentonite block near the canister decreases in the early stage, because water evaporation occurs owing to temperature increase. Then, saturation of the bentonite buffer and backfill increases because of water intake from the rockmass, and bentonite buffer and backfill are fully saturated after about 266 years. The stress is calculated to investigate the effect of thermal stress and swelling pressure on the mechanical behavior of the rockmass. The calculated stress is compared to a spalling criterion and the Mohr-Coulumb criterion for investigation of potential failure. The stress at the rockmass remains below the spalling strength and Mohr-Coulumb criterion for the whole period. The methodology of using the TOUGH2-MP/FLAC3D simulator can be applied to predict the long-term behavior of the KRS under various conditions; these methods will be useful for the design and performance assessment of alternative concepts such as multi-layer and multi-canister concepts for geological spent fuel repositories.

• The Journal of Industrial Distribution & Business
• /
• v.2 no.1
• /
• pp.5-15
• /
• 2011

Prior to the introduction of the CRM, we need to analyze the characteristics and the situations of the company, and should establish a clear vision of the CRM. And each company should identify elements and technologies for introducing the most suitable CRM for them, and optimize them, with long-term perspective. In addition, it requires the implementation strategy which integrates the existing company's routine marketing activities with the concept of the CRM. According to the implementation strategy, the company should improve the business process which is the most effective in investment step by step, and the information system strategy, which develops system investment gradually, should harmonize with it. First, we recognized that raising the company value is important by maximizing customer lifetime value (LTV) by understanding customer needs, and achieving the company's goal through customer satisfaction. Second, we understood that adopting the CRM should be accompanied by changes in the structure, business process and customer contact channels, and it can be successfully integrated with business when it gets proper understandings and attentions of the management. Third, the reality is that there are few cases of successful implementation of domestic companies, and some companies that successfully implement the system mean nothing but implement the solution for developing the CRM. Therefore, it needs to be observed for the long haul, and it seems that we need to approach more systematically to implementation cases for each industry about implementation of the CRM. Fourth, the CRM is no longer the preserve of major companies, and it is the time that medium and small sized enterprises also need it. Taking lesson from Switzerland's small size store merchants who successfully adopt right size of the CRM for their business, for domestic medium and small sized enterprises, the necessity to develop business through developing the CRM models which fit their situations and maintaining relationships with customers has been grown. Fifth, for adopting the CRM business processes, changing or converting the CRM system to the model which fits the company's situation is important rather than applying the advanced company's CRM system model. In other words, the CRM solution which can maximize their own strength by developing the CRM program that makes the most of features and characteristics of the company should be adopted.

• 한국해양학회지
• /
• v.30 no.6
• /
• pp.550-564
• /
• 1995

The temporal and spatial characteristics of wind fields over the neighbouring seas of the Korean peninsula are investigated using 10-years daily wind data during 1978${\sim}$1987 which have been spatially smoothed and low-pass filtered. Long term annual and monthly means are examined for synoptic patterns and spectral analyses are made for temporal variability and spatial coherence. Spatial patterns of the annual mean wind stress and curl have a strong resemblance with those of monthly means during the winter season. Two outstanding periodicities are observed at 1 and 2 cycles per year. The synoptic winds over the study area are highly coherent at both the annual and semi-annual periodicities. However, each basin has its own characteristic spatial pattern. For instance, the prevailing wind during the winter season is northerIy over the northern East Sea (ES), Yellow Sea (YS), and northern East China Sea (ECS), while it is northwesterly over the southern ES and northesterly over the northern ES and southern ECS. At the same time, the wind stress curl is positive over the northern ES and southern ECS, while it is negative over the southern ES, YS and northern ECS. On the other hand, the wind field during the summer season, with its strength being much reduced, is completely different from that during the winter season, and frequent passage of tropical storms provokes large temporal variability over ECS. One remarkable point is that the annual cycle, dominated by the Siberian High, tends to propagate from northeast to southwest, i.e., from northern 25 toward southern ES, YS and ECS, while the semi-annual cycle propagates in the opposite direction, from southwest to northeast. The semi-annual periodicity may reflect development of extratropical cyclones in spring and fall which frequently cross the Korean peninsula. In higher frequencies, there are no dominant periodicities, but local winds over YS and ES are highly correlated for frequencies larger than 0.1 cycles per day and phase difference increases linearly with frequency. This linear increase of phase corresponds to phase speed of 550 and 730 km/d at 0.1 and 0.3 cpd, respectively, The phase speed is apparently coincident with moving speed of extratropical cyclones across the Korean peninsula in the west-east direction.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.1 no.1
• /
• pp.8-16
• /
• 2013

Currently, global warming has advanced by the usage of fossil fuels such as coal and petroleum. and the atmosphere temperature in the world of 100 years(1906~2005) has been risen $0.74^{\circ}C{\pm}0.18^{\circ}C$, IPCC announced that the global warming effect of last decade was nearly doubled compared to the changes($0.07^{\circ}C{\pm}0.02^{\circ}C$/10year) in the past 100 years. Moreover, due to the global warming, heat wave, heavy snow, heavy rain, super typhoon, were caused and are increasing to happen in the world continuously causing damages and destruction of social infrastructures, where concrete structures are suffering deterioration by long-term extreme climate changes. to solve these problems, the new construction technology and codes are necessary. In this study, to solve these problems, experiments on a variety of cases considering the temperature and humidity, the main factors of climate factors, were performed, and the cases are decided by temperature and humidity. The specimens were tested in compressive strength test and split tensile test by the curing age(3,7,28 days) morever, performance based design(PBD) method was applied by using the satisfaction curve developed from the experiment date. PBD is the design method that gathers the current experimental analysis and past experimental analysis and develops the material properties required for the structure, and carries out the design of concrete mix, and it is recently studied actively worldwide. Also, it is the ultimate goal of PBD to design and perform on structures have sufficient performance during usage and to provide the problem solving for various situations, Also, it can achieve maximum effect in terms of functionality and economy.

• Journal of Hospice and Palliative Care
• /
• v.21 no.1
• /
• pp.9-13
• /
• 2018

Purpose: The purpose of this study was to assess the factors influencing the rescue medication decisions for breakthrough cancer patients and evaluate treatments using the factors. Methods: Based on the results of an online survey conducted by the Korean Society of Hospice and Palliative Care from September 2014 through December 2014, we assessed the level of agreement on nine factors influencing rescue medication preference. The same factors were used to evaluate oral transmucosal fentanyl lozenge, oral oxycodone and intravenous morphine. Results: Agreed by 77 physicians, a rapid onset of action was the most important factor for their decision of rescue medication. Other important factors were easy administration, strong efficacy, predictable efficacy and less adverse effects. Participants agreed that intravenous morphine produced a rapid onset of action and strong and predictable efficacy and cited difficulty of administration and adverse effects as negative factors. Oral oxycodone was desirable in terms of easy administration and less adverse effects. However, its onset of action was slower than intravenous morphine. While many agreed to easy administration of oral transmucosal fentanyl lozenge, the level of agreement was low for strength and predictability of its efficacy, long-term durability and sleep improvement. Conclusion: Rapid onset of action is one of the important factors that influence physicians' selection of rescue medication. Physicians' assessment of rescue medication differed by medication.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.1
• /
• pp.4-21
• /
• 2019

In this paper, 23 Silla gold earrings from the sixth and seventhand centuries, excavated from the Yeongnam region, were analyzed. Based on the silver content of the gold plate, they were classified into three types. The classifications included type I(20-50wt%), type II(10-20wt%) and type III (less than 10wt%). In the analysis process, the composition and morphological differences were identified on the surface of the gold plate. In the case of type I and II earrings, it was observed that the fine holes were concentrated in a relatively higher part of the gold content. The causes of the difference in the surface composition of the gold plate were divided into four categories: 1) surface treatment, 2) thermal diffusivity in the manufacturing process, 3) differences in composition of alluvial gold, and 4) the refining method of gold. It is possible that depletion gilding was attempted to increase the gold content while intentionally removing the other metals from the surface of the gold alloy in the portion where the gold deposit is relatively concentrated on the surface of the gold plating. The highest copper content was detected in the earring with the highest gold content of the analyzed earrings, and it was assumed that thermal diffusion had occurred between the gold plate and the metal rod during the manufacturing process rather than intentional addition. Copper was detected only in the thin ring earring type, and copper was not detected in the thick ring earring type or pendant type. It also proves that this earring has a high degree of tightness at higher temperatures, as there was an invisible edge finish on other earrings and horizontal wrinkles on the gold plate surface. In terms of the material of the gold plate, we examined whether the silver content of the gold plate was natural gold or added by alloy through analyzing the alluvial gold collected in the region. As a result of the analysis, it was found that on average about 13wt% of silver is included. This suggests that type II is natural gold, type III is refined gold, and type I seems to have been alloyed with natural gold. Here, we investigated the refining method introduced in the ancient literature, both at home and abroad, about the possibility of alloying silver after the refining process of type III earrings and then making pure gold. It was found that from ancient refining methods, silver which had been present in the natural gold was removed by reacting and combining with silver chloride or silver sulfide, and long-term efforts and techniques were required to obtain pure gold through this method. Therefore, it was concluded that the possibility of adding a small amount of silver in order to increase strength after making pure gold through a refining process is low.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.188-197
• /
• 2020

Termites play an important role as decomposers of the forest ecosystem, while simultaneously causing enormous damage to wooden structures. Currently, two species of subterranean termites have been reported in Korea, and termite damage to historical wooden buildings is occurring nationwide due to climate change, forest fertility, and the locational characteristics of historical wooden buildings. Subterranean termites make their nests underground or inside timber. Termites move underground and access wooden structures through the lower parts of the buildings, adjacent to the ground. Once termites attack the wooden structures, it not only spoils the authenticity of cultural heritage structure, but also hampers structural stability due to the decrease in the strength of the material. Therefore, it is important to prevent termite damage before it occurs. Chemical treatments are mainly used in Korea to control and prevent the damage. In foreign countries, physical barriers are also used to prevent entry to wooden buildings, along with chemical treatments. Physical barriers involve installing nets or particles that termites cannot pass through in the lower part of the building, around the pipes, and between the edges of the building or exterior walls and interior materials. Advantages of a physical barrier are that it is an eco-friendly method, maintains long-term effect after installation, and does not require the use of chemical treatments. Prior to applying physical barriers, studies into the characteristics of termite species must be undertaken. In this study, we evaluated the minimum passage size that each caste of Reticulitermes speratus kyushuensis can move through. We found that workers, soldiers, and secondary reproductive termites were able to pass through diameters of 0.7mm, 0.9mm, and 1.1mm respectively. Head height of termites was an important factor in determining the minimum passing size. Results from the current study will be used as a basis to design the mesh size for physical barriers to prevent damage by termites in historical wooden buildings in Korea.

• 한국노년학
• /
• v.27 no.2
• /
• pp.459-472
• /
• 2007

This research has its purpose of developing a tool to assess the needs of the Korean elderly at home population and to provide adequate services by evaluating their physical, psychological, and socio-environmental aspects. This developed tool is composed of two hundred questions and has the advantage of combined physical, psychological and social environmental situation assessment of the elderly at home. The tool also contains not only the objective view of the professionals, but also the subjective appeals of the elderly at home population so that it can reflect their substantial desires. The assessment tool was developed over 21 months from July, 2004 to March, 2006 and this period can be divided into three different stages. In the first stage, collecting of questions for the desire-focused assessment of the elderly by literature investigation and researching foreign source materials was carried out, and this ultimately developed assessment tool was applied to the long-term care insurance pilot project in the second stage. In this process, we revised some insufficiencies of this tool after we applied to elderly of 250 from the pilot project and other 200 elderly from this research team. For the last stage, the tool was completed by using inquiries of the focused group and the group of professionals to ensure its reliability and validity. In the process of developing the tool, the total of 200 questions under 13 subcategories was selected. The 13 subcategories are basic information, subjective appeals, information of the main helper, use of services, house environment, condition of health, condition of rehabilitation, daily living(ADL, IADL, defecation, assistance), social maintenance, behavioral disability, medical health, living habits, and strength. This tool is on the purpose to assess thoroughly the desires that the elderly at home population has and to provide the best service they need.

• Journal of Korean Society of Forest Science
• /
• v.29 no.1
• /
• pp.1-19
• /
• 1976

This study has been made to make an observation regarding present status of the coal mine props which is desperately needed for coal production, despite of great shortage of the timber resources in this country, and investigate the effects of diffusion process on the decay resistances of the mine props as applied preservatives of Malenit and chromated zinc chloride. The results are as follows. 1. Present status of the coal mine props Total demand of coal mine props in the year of 1975 was approximately 456 thousand cubic meters. The main species used for mine props are conifer (mainly Pinus densiflora) and hardwood (mainly Quercus). Portions between them are half and half. With non fixed specification, wide varieties of timber in size and form are used. And volume of wood used per ton-of coal production shows also wide range from 0.017 cubic meter to 0.03 cubic meter. 2. Decay resistance test a) The oven dry weight decreased between untreated specimen and treated specimen has not shown any significantly, although it has shown some differences in average values between them. It may be caused by the shorter length of the test. b) The strength of compression test between untreated specimen and treated specimen has also shown the same results as shown in case of weight decrease. Reasons assumed are the same. c) The amounts of the extractives in one percent of sodium hydroxide (NaOH) between untreated and treated specimen have shown the large value in case of untreated specimen than that of treated. 3. The economical benifit between untreated and treated wood when applied in field has seen better in long term base in case of treated wood, although the primary cost of treated wood add a little bit more cost than that of the untreated wood.