• 터널과지하공간
• /
• 제6권3호
• /
• pp.197-208
• /
• 1996

Due to the constraints in pre site-investigation for tunnel, it is essential to redesign the support structures suitable for rock mass conditions such as rock strength, ground water and discontinuity conditions for safe tunnel construction. For the selection of optimum support, it is very important to carry out the rock mass classification and in-situ measurement in tunnelling. In this paper, in a mountain tunnel designed by NATM in hard rock, the selectable system for optimum support has been studied. The tunnel is situated at Chun-an in Kyungbu highspeed railway line with 2 lanes over a length of 4, 020 m and a diameter of 15 m. The tunnel was constructed by drill & blasting method and long bench cut method, designed five types of standard support patterns according to rock mass conditions. In this tunnel, face mapping based on image processing of tunnel face and rock mass classification by RMR carried out for the quantitative evaluation of the characteristics of rock mass and compared with rock mass classes in design. Also, in-situ measurement of convergence and crown settlement conducted about 30 m interval, assessed the stability of tunnel from the analysis of monitoring data. Through the results of rock mass classification and in-situ measurement in several sections, the design of supports were modified for the safe and economic tunnelling.

• Geomechanics and Engineering
• /
• 제20권2호
• /
• pp.103-112
• /
• 2020

The dynamic response of crossing tunnels under heavy-haul train loads is still not fully understood. In this study, based on the case of a high-speed tunnel underneath an existing heavy-haul railway tunnel, a model experiment was performed to research the dynamic response characteristics of crossing tunnels. It is found that the under-crossing changes the dynamic response of the existing tunnel and surrounding rock. The acceleration response of the existing tunnel enhances, and the dynamic stress of rock mass between crossing tunnels decreases after the excavation. Both tunneling and the excitation of heavy-haul train loads stretch the tunnel base, and the maximum tensile strain is 18.35 µε in this model test. Then, the measured results were validated by numerical simulation. Also, a parametric study was performed to discuss the influence of the relative position between crossing tunnels and the advanced support on the dynamic behavior of the existing tunnel, where an amplifying coefficient of tunnel vibration was introduced to describe the change in acceleration due to tunneling. These results reveal the dynamic amplifying phenomenon of the existing tunnel during the new tunnel construction, which can be referred in the dynamic design of crossing tunnels.

• 한국구조물진단유지관리공학회 논문집
• /
• 제14권3호
• /
• pp.196-200
• /
• 2010

본 연구에서는 철도터널내 화재시 터널내 구조체의 내화성능을 평가하기 위한 시간-온도곡선의 기준을 제시하고자 실시하였다. 현재 국내에서는 철도터널건설과 터널의 수가 빠른 속도로 증가하고 있으며, 터널연장이 길어짐에 따라 터널 내 화재사고가 갈수록 높아지고 있는 상황이다. 철도터널의 화재빈도수는 적지만 화재시 인명과 교통차단으로 인한 사회적 피해는 막대하다. 하지만 우리나라에서는 철도터널 화재에 대한 적합한 시간-온도 곡선을 규정하지 못하고 있는 실정이다. 따라서 본 연구에서는 국내 철도의 통행량, 차량종류 등을 고려한 열방출율을 기초로 외국에서 제시된 시간-온도 곡선을 검토해 보았으며 국재 실정에 가장 적합한 설계화재 모델을 제시하였다. 탄화수소(HC)시간-온도 곡선이 국내 철도터널의 설계화재모델로 가장 적합하였으며, 탄화수소 시간-온도곡선에 의한 철도터널 구조체의 온도분포를 예측하기 위하여 유한요소해석을 통하여 콘크리트터널 구조체의 구조성능을 검토하였다.

• 한국터널지하공간학회 논문집
• /
• 제17권2호
• /
• pp.153-166
• /
• 2015

일반적인 장대 철도터널에 비해 해저터널은 환기 및 방재를 위한 별도의 연직갱 또는 경사갱 설치에 공간상 많은 제약을 받게 되므로, 인공섬을 건설하여 환기를 수행할 필요가 있다. 그러나, 인공섬 설치에는 시공상의 문제 뿐만 아니라 건설비용이 증가하게 되므로, 인공섬 설치를 최소화하여 환기구간 거리를 늘려야 한다. 이에 따른 환기거리의 증가시, 누풍에 의한 신선공기 공급량이 커지게 된다. 공급풍량이 과대해지면, 구조물 한계에 의해 설치가능한 덕트직경이 제한적이므로, 팬 정압 및 동력도 상당히 증가하게 된다. 따라서, 초장대 해저터널을 건설하기 위해서는 이러한 현실적인 문제를 극복하고, 시공중 터널내 환경을 쾌적한 상태로 유지할 수 있는 기술력이 필요하다. 본 논문에서는 이러한 초장대 해저터널에 적합한 공사중 환기 방식을 개발하기 위한 기본연구로써, 국내외의 공사중 환기용량 산정방법 비교를 통해, 스위스의 SIA 196 코드가 초장대 해저터널계획에 적합함을 확인하였다. 또한, 덕트 접속부의 누출에 관한 실험을 통해, 국내의 덕트 접속방식은 100 m당 누풍율이 1.5~3.0% 사이임을 확인하였다. S등급 덕트의 경우 환기가능거리가 10.2 km 이므로, 덕트의 접속방법을 개선한다면, 환기가능거리는 더 길어질 수 있다. 따라서, 공사중 덕트의 누풍개선이 초장대 해저터널의 공사중 환기의 주요 이슈임을 확인하였다.

• Advances in concrete construction
• /
• 제11권5호
• /
• pp.375-386
• /
• 2021

In this paper, a study of stability and health of a newly-built railway tunnel is presented. The field test was implemented to monitor the secondary lining due to the significant cracking behaviors influenced the stability and health of the tunnel structure. Surface strain gauges were installed for monitoring the status of crack openings, and the monitoring outputs demonstrated that the cracks were still in the developing stage. Additionally, adjacent tunnel and poor condition of surrounding rock were identified as the causes of the lining cracking by systematically characterizing the crack spatial distribution, tunnel site and surrounding rock conditions. Reconstruction of partial lining and reconstruction of the whole secondary lining were designed as the maintenance projects for different cracking regions based on the construction feasibility. For assessing the health conditions of the reinforced lining, embedded strain gauges were set up to continuously measure the strain and the internal force of the reconstructed structures. For the partially reconstructed lining, the outputs show the maximum tensile elongation is 0.018 mm during 227 days, which means the structure has no obvious deformation after maintenance. The one-year monitoring of full-section was implemented in the other two completely reconstructed cross-sections by embedded strain gauge. The outputs show the reconstructed secondary lining has undertaken the pressure of surrounding rock with the time passing. According to the calculated compressive and tensile safety factors, the completely reconstructed lining has been in reliable and safe condition during the past year after reinforcement. It can conclude that the aforementioned maintenance projects can effectively ensure the stability and health of this tunnel.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1319-1324
• /
• 2007

Many researches have been performed to analyze the smoke movement in tunnel fires by using field model. Recently, FDS(Fire Dynamics Simulator) v.4, which is one of the field model and developed from NIST(National Institute of Standards and Technology), is widely used. In tunnel fires, FDS can show detail results in local point, but it has difficulties in boundary condition and taking long computing time as the number of grid increases. So, there is a need to use alternative method for tunnel fire simulation. A zone model is different kind of CFD method and solves ordinary differential equation based on conservation and auxiliary equations. It shows good macroscopic view in less computing time compared to field model. In this study, therefore, to confirm the applicability of CFAST in tunnel fire analysis, numerical simulations using CFAST are conducted to analyze smoke movement in longitudinal ventilation reduced-scale tunnel fires. Then the results are compared with experimental results. The differences of temperature and critical velocity between numerical results and experimental data are over $30^{\circ}C$ and 0.9m/s, respectively. These values are out of error range. It shows that CFAST 6.0 is hard to be used for tunnel fire simulation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.1354-1363
• /
• 2006

Until now, NATM(New Austrian Tunneling Method) has been increasingly developed based on concept of making use of ground as support. Also, NATM in its essence is a method of risk based on monitoring behaviour of tunnel. This Monitoring is irreplaceable for the quality construction of tunnel, and safety of tunnel itself. Pre-reinforcement ahead of a tunnel face using long steel pipes in NATM, known as the RPUM(Reinforced Protective Umbrella Method), is the auxiliary method to sustain the stability of a tunnel face and reduce the ground settlements. Since design of RPUM has been dependent on the empirical design, it is necessary to develop the improved design methods. In this study, to understand behaviour of steel pipes, it is monitored displacement of tunnel crown, axial force of rock bolt, displacement and axial stress of steel pipes. Also, in order to clarify the mechanical behaviour and RPUM effects, 3-Dimensional numerical analysis is performed that various cases of different parameter combinations including original length and repeated length of steel pipes, installation width and angle, repeated length of steel. In the results of comparison monitoring with analysis, it is suggested more economical and efficient design technique than empirical design methods.

• 한국전산유체공학회지
• /
• 제17권1호
• /
• pp.23-28
• /
• 2012

The pressure transient inside the passenger cabin of high-speed train has been simulated using computational fluid dynamics(CFD) based on the axi-symmetric Navier-Stokes equation. The pressure change inside a train have been calculated using first order difference approximation based on a linear equation between the pressure change ratio inside a train and the pressure difference of inside and outside of the train. The numerical results have been assessed for the KTX train passing through a 9km long tunnel of Wonju-Kangneung line at the speed of 250km/h assuming that the train is satisfying the train specification for airtightness required by the regulation.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.337-342
• /
• 2011

The pressure transient inside the passenger cabin of high-speed train has been simulated using computational fluid dynamics(CFD) based on the axi-symmetric Navier-Stokes equation. The pressure change inside a train have been calculated using first order difference approximation based on a linear equation between the pressure change ratio inside a train and the pressure difference of inside and outside of the train. The numerical results have been assessed for the KTX train passing through a 9km long tunnel of Wonju-Kangneung line at the speed of 250km/h assuming that the train is satisfying the train specification for airtightness required by the regulation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1330-1336
• /
• 2007

본 연구는 미기압파 해석에 필요한 각종계수의 도출 및 해석결과의 신뢰성을 검증하기 위한 목적이 있다. 본 실험에 사용된 터널 주행 열차모형 실험 장치는 1/60축척으로 제작 되었으며, 열차는 KTX 차량 모델의 제원에 맞추어 10량 1편성으로 제작된 모형을 사용하였다. 터널의 다면적은 $107.9m^3$ 와 $95.1m^3$를 적용하고, 터널연장은 1km, 0.78km, 0.5km를 적용하였고, 열차속도는 275, 300, 325, 350km/h로 변화시켜 실험 하였다. 실험 장치는 유압발사 시스템으로 열차모델 유압 발사기터널모델 제동장치로 구성된다. 모형열차의 속도는 터널입구 전방 및 출구 부 갱구에서 각각 1.2m지점에서 설치한 속도 감지기에 의해서 측정되며, 터널 내부의 압력변동은 압력센서를 터널의 입구, 중앙, 출구부에 설치하여 연속적으로 측정 하였다. 측정결과 터널입구에서 발생한 압력파의 압력기울기는 터널을 전파하면서 비선형효과에 의해서 증가하거나 확산작용에 의해서 압력기울기가 감소하는 것을 알 수 있었고, 미기압파 저감 대책을 위해 터널입구에 종류별 각각 설치하여 출구부에서 발생되는 미기압파를 비교분석하여보았다.