• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.963-968
• /
• 2005

For worm robots applied to pipe inspection and colonoscopy, earthworm-like robots that have a locomotion pattern in backward wave or green caterpillar-like robots that have a locomotion pattern in forward wave have been studied widely. Note however that a method using a single and fixed locomotion pattern is not desirable in the sense of mobility cost, if there are various changes in pipe diameter. In this paper, locomotion patterns are considered for a semi-looper-like robot, which adopts a locomotion pattern of green caterpillars as the basic motion and sometimes can realize a locomotion pattern of looper, whose motion approximately consists of two rhythms or relatively low rhythm.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.592-595
• /
• 1986

This paper presents a mobile of robot (for the blind) commanded by written course route on MAP. Its locomotion module is composed of PWM motor driving unit, wheel's rotation measurement unit and display and keyboard unit. In algorithm, "COMMAND" and "NEXT PREDICTED POSITION" for locomotion are computed from the MAP and the next position is compared with the measured one. Also, locomotion method for the convenience of the blind is discussed and experimentally demonstrated. In the experiment, the average speed of robot is 0.4m/sec and the computation error of the map is negligible.

• Journal of Biomedical Engineering Research
• /
• v.8 no.1
• /
• pp.49-56
• /
• 1987

This paper designed LOCOMOTION SYSTEM of a mobile robot for the blind guidance and LOCOMOTION COMMAND SYSTEM that gave the moving path to the locomotion system. This system analyzed COMMAND and calculated the speed and direction of the robot. And during locomotion it measured wheel's rotation number for the position and speed control. Also, this system was considered about the 110 interface with host computer and the locomotion method for the blind. In the locomotion experiment the standard speed of robot was 0.4m/sec and the locomotion error was below 5%

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.6
• /
• pp.604-611
• /
• 2009

Modular snake-like robots are robust for failure and have flexible locomotion for environments, but are difficult to control. Various phase and evolutionary approaches for modular robots have been studied for many years, but there are few comparisons among these methods. In this paper, Phase, GAps, GA and GP approaches are implemented and compared for flat, stairs, and slope environments. In addition, simulations of the locomotion evolution for modular snake-like robot are executed in Webots environments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.9
• /
• pp.782-790
• /
• 2013

In this paper, we propose a better solution for swimming plans of an articulated underwater robot, Crabster, with a view point of biomimetics. As a biomimetic model of underwater organisms, we chose diving beetles structurally similar to Crabster. Various swimming locomotion of the diving beetle has been observed and sorted by robotics technology through experiments with a high-speed camera and image processing software Image J. Subsequently, coordinated patterns of rhythmic movements of the diving beetle are reproduced by simple control parameters in a parameter space which make it easy to control trajectories and velocities of legs. Furthermore, a simulation was implemented with an approximated model to predict the motion of the robot under development based on the classified forward and turning locomotion. Consequently, we confirmed the applicability of parameterized leg locomotion to the articulated underwater robot through the simulated results by the approximated model.

• Journal of Mechanical Science and Technology
• /
• v.16 no.1
• /
• pp.83-93
• /
• 2002

This paper presents a motion control method and its simulation results of a mobile robot for a lattice type welding. Its dynamic equation and motion control methods for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven for following straight line or curve. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider control. For the torch slider control, the proportional-integral-derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the corner with range of 90$^{\circ}$ constrained to the welding speed. The proposed control methods are proved through simulation results and these results have proved that the mobile robot has enough ability to apply the lattice type welding line.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.923-928
• /
• 2003

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or comer. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The proposed control methods are proved through simulation results and the results have proved that the mobile robot has enough ability to apply the lattice type welding line.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.311-314
• /
• 1995

Biped locomotion can be simply modeled as a linear inverted pendulum mode. This model considers only the CG (center of gravity) of the entire system. But in real biped robot systems, the free-leg motion dynamics is not negligible. So if its dynamics is not considered in designing the reference CG motion, it is badly influence to the ZMP(zero moment point) position of the biped robot walking in the sagittal plane. Therefore, we modeled the biped locomotion similar to the linear inverted pendulum mode but considered the predetermined free-leg dynamics. To verify that the proposed biped locomotion is more stable than the linear inverted pendulum mode, we constructed a biped robot simulator and designed a serco controller to track both the reference motion of the free leg and the reference motion of CG of the biped robot using the computed torque control low. And through simulations, we verified that the proposed walking is better in stability than the one based on the linear inverted pendulum mode.

• Proceedings of the KSME Conference
• /
• 2001.06b
• /
• pp.319-324
• /
• 2001

This paper presents the motion control of a mobile robot with arc sensor for lattice type welding. Its dynamic equation and motion control method for welding speed and seam tracking are described. The motion control is realized in the view of keeping constant welding speed and precise target line even though the robot is driven along a straight line or corner. The mobile robot is modeled based on Lagrange equation under nonholonomic constraints and the model is represented in state space form. The motion control of the mobile robot is separated into three driving motions of straight locomotion, turning locomotion and torch slider controls. For the torch slider control, the proportional integral derivative (PID) control method is used. For the straight locomotion, a concept of decoupling method between input and output is adopted and for the turning locomotion, the turning speed is controlled according to the angular velocity value at each point of the comer with range of $90^{\circ}$ constrained to the welding speed. The experiment has been done to verify the effectiveness of the proposed controllers. These results are shown to fit well by the simulation results.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.21 no.1
• /
• pp.132-137
• /
• 2011

The walking mobility with stability of 4 legged robots is the distinguished skills for many application areas. Planning gaits of efficient walking for quadruped robots is an important and challenging task. Especially, autonomous generation of locomotion is required to manage various robot models and environments. In this paper, we propose an adaptive locomotion control of 4 legged robot for irregular terrain using HyperNEAT. Generated locomotion is executed and analysed using ODE based Webots simulation for the 4 legged robot which is built by Bioloid.