• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2475-2482
• /
• 1993

The effects of the hole size(2R) and the specimen width(W) on the fatigue strength and the fatigue life in plain woven glass/epoxy composite plates are experimentally investigated under constant amplitude tensile fatigue loading. It is shown in this study that the notch sensitivity under fatigue loading is lower than that under static loading. It can be explained by the fact that the stress concentration is relaxed by the damage developed at the boundary of circular hole. To predict the fatigue strength at a specific cycle, the modified point stress criterion represented as a function of the geometry of the specimen(2R and W) is applied. It is found that the model used in the prediction of the notched tensile strength predicts the fatigue strength with reasonable accuracy. A model for predicting the fatigue life in the notched specimen, based on the S-$N_f$, curve in the smooth specimen, is suggested.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.2
• /
• pp.66-73
• /
• 2021

In the existing study of steel beams with openings, openings are located at a location where the distance to the support point is equal to or greater than the section height. Considering the facilities using the openings in the steel beam, the distance from the opening to the support point may be closer than the height of the beam section. Therefore, research on this is needed. This study is an experimental study to understand the structural performance of beams with openings close to the ends subjected to Cyclic Loading. In addition, in this study, we want to understand the structural performance through experiments on beams with openings reinforced with vertical or horizontal steel plates.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.2
• /
• pp.145-154
• /
• 2009

This study discusses the inelastic behavior of single-layer latticed dome, which consists of a tubular truss member and newly proposed joint sections, through a loading test on a scaled-down structure. The loading test was performed under displacement control conditions, using loading transfer system for the same value of point loads on all joints. The maximum applied load was nearly 1.6 times of the design load, and structural failure occurred after exceeding the compressive yielding in some members. Structural displacement was maintained up to the limit of the oil jack. The behavior of the latticed dome from the loading test was analyzed according to the order of loading steps.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.220-227
• /
• 2009

In the process of oyster mushroom production, loading work of culture medium needs the most intensive labor power. Therefore, development of culture medium machine causes to reduce the manpower and cost. The main objective of this study is to develop the culture medium loading machine and investigate the optimal operation conditions and to evaluate the economic value of the machine. The results are summarized as follows: 1. Optimum transporting velocity of the conveyor was 0.61 m/s 2. Optimum speed of blower was 3183 rpm at the transporting velocity of 0.61 m/s with the loading quantity of 3.41 t/hr 3. Recommendable opening area ratio of pressure controller was 1/2 at the blower speed of 3183 rpm and the transporting velocity of 0.61 m/s 4. The break even point resulted in $240\;m^2$ of cultivating area compared to the method of with portable workbench, and $350\;m^2$ of cultivating area compared to the method of with a tractor and a truck.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.3
• /
• pp.73-79
• /
• 2010

In the present study, the loading frequency dependencies of cyclic shear strength and elastic shear modulus of reconstituted clay were examined by performing undrained cyclic triaxial tests and undrained cyclic triaxial tests to determine deformation properties. The result of undrained cyclic triaxial test of reconstituted and saturated clay shows that a faster frequency leads to higher stress amplitude ratio, but when the frequency becomes fast up to a certain point, the stress amplitude ratio will reach its maximum limit and the frequency dependence becomes insignificant. And also, the result of undrained cyclic triaxial deformation test shows a fact that a faster loading frequency leads to higher equivalent shear modules and smaller hysteresis damping ratio, and confirms the frequency dependence of cohesive soil. Meanwhile, the result of the creep test shows that continuing creep is created in the undrained cyclic triaxial test with slow loading frequency rate, and since loading rate becomes slower at the vicinity of the maximum and the minimum deviator stress due to sine wave loading, the vicinity of the maximum and the minimum deviator stress shall be more influenced by creep.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.197-202
• /
• 2001

It is necessary to Investigate long-term behavior of vertical members such as column and shear wall because the long-term behavior induces the serviceability problem of reinforce-concrete structures. However, the long-term behavior on shear wall has not been fully studied. Experimental works are performed to understand the time dependent behavior of shear wall, especially the effect of loading area in this research. Three different types of cross sections are adopted, i.e., 10$\times$10 cm, 10$\times$30 cm, and 10$\times$50 cm with the same loading area of 10$\times$10 cm. The creep strains were different from point to point in the section of the shear wall specimen because of the nonlinear stress distribution. The effect of the nonlinear stress distribution was larger in the specimen with the larger width.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.399-402
• /
• 2001

After the legal foundation for the Total Load Control System (TLCS) process is embedded in integrated water management counterplan for 4 major river basins (1998), Kyunggido Kwangju City prepared the implementation plan of TLCS at first time. There is little difference between TLCS and TMDL(Total Daily Maxium Loading; U.S.A). TMDL is applied only when mandatory effluent limitations are not stringent enough to attain any water quality standard. But object of TLCS not only attain water quality standard at distributed watershed but also consider development of area at non-distributed watershed. For applying of systematic and consistent TLCS, we need to establish a system integrated watershed and point source, non-point source and assessed massive database easily. Now we are study on applicable possibility of BASINS on Korea, we think that BASINS's tool and many models are more easily apply to TLCS, so we recommend TLCS will be applied using BASINS.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.254-256
• /
• 2009

The performances of proton exchange membrane (PEM) water electrolysis depend on many factors such as materials, geometries, fabrication methods, operating conditions, and so forth. The fabrication method is concerned, membrane electrode assemblies (MEA) are a most important part to show different performances by different fabrication methods. The performance change of PEM water electrolysis was experimentally measured according to the fabrication differences of the anode electrodes. One point of view is the catalyst intrusion rate to the anode gas diffusion layer (GDL), and the other point of view is the catalyst loading distribution in depth of the anode GDL. Results show that the performances of MEA with deep intrusion of the catalysts are better in the range of low current densities but worse at higher current densities. The catalyst loading distribution does not affect significantly to the performance of PEM water electrolyser.

• New & Renewable Energy
• /
• v.5 no.4
• /
• pp.75-78
• /
• 2009

The performances of proton exchange membrane (PEM) water electrolysis depend on many factors such as materials, geometries, fabrication methods, operating conditions, and so forth. The fabrication method is concerned, membrane electrode assemblies (MEA) are a most important part to show different performances by different fabrication methods. The performance change of PEM water electrolysis was experimentally measured according to the fabrication differences of the anode electrodes. One point of view is the catalyst intrusion rate to the anode gas diffusion layer (GDL), and the other point of view is the catalyst loading distribution in depth of the anode GDL. Results show that the performances of MEA with deep intrusion of the catalysts are better in the range of low current densities but worse at higher current densities. The catalyst loading distribution does not affect significantly to the performance of PEM water electrolyser.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.311-314
• /
• 1999

This study is aim to evaluate of the flexural performance of specialty cellulose fiber reinforced concrete. Flexural test is proceeded by third-point loading method and the size of the test specimens is 15$\times$15$\times$55cm. The rate of loading was 0.006mm/min. The effects of differing fiber volume fraction(0.08%, 0.1%, 0.15%) were studied. The results of test on the specialty cellulose fiber reinforced concrete were compared with plain and polypropylene fiber reinforced concrete. Results indicated that specially cellulose fiber reinforcement showed an improvement of flexural performance.