• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2005년도 추계학술대회 논문집
• /
• pp.54-57
• /
• 2005

Flow characteristics of hull wake behind a container ship model were investigated experimentally with varying loading condition and Reynolds number. Large-scale bilge vortices of nearly the same strength are formed in the near-wake region. They are symmetric and counter-rotating with respect to the wake centerline for all loading conditions tested. With going downstream for both design and ballast loading conditions, the strength of the bilge vortices decreases and the wake region expands due to diffusion and viscous dissipation. Under the design loading condition, the bilge vortices start to appear at St=0.363 transverse plane above the propeller-boss. For the ballast loading condition, however, the bilge vortices start to appear at St=0.591 below the propeller-boss. They move upward as the hull wake goes downstream and Reynolds number increases. These wake characteristics, under the ballast loading condition, may weaken the propulsion and cavitation performances of the propeller, which are usually optimized for the design loading condition.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2015년도 특별논문집
• /
• pp.93-95
• /
• 2015

In case of crude oil tanker, loading condition must be satisfied MARPOL damage stability criteria (Reg.28). But some specific demands are hard to content the criteria. So, it takes a lot of time and efforts to make loading condition reflecting these demands. In this study, PSO (Particle Swarm Optimization) is used to make loading condition to be satisfied the criteria. Study result is applied 'CROSSWAY (160,000 DWT Crude Oil Tanker)' in NAPA. The result shows that satisfy the criteria and other constraints and limitation.

• 터널과지하공간
• /
• 제24권3호
• /
• pp.224-233
• /
• 2014

지하 하중 조건에서 암석물성이 변한다는 것은 잘 알려져 있다. 따라서 침수상태에 놓인 폐광산이나 폐공동에서의 하중에 따른 암석 물성변화와 일반적인 건조상태의 하중에 따른 물성 변화와의 관계에 대하여는 연구가 필요하다. 침수-하중 조건에서의 암석 물성 변화를 파악하기 위해 다양한 실험실 실험이 실시되었다. 암석에 가해지는 하중은 단축압축강도의 20~80%로 조절하였다. 침수 및 건조 조건에서 동일한 하중을 가할 경우 발생하는 암석의 열적, 역학적, 물리적 물성 변화를 비교함으로써 건조조건에 비해 침수조건에서의 물성변화가 더 크게 일어남을 알 수 있었다.

• 한국농공학회논문집
• /
• 제51권6호
• /
• pp.83-90
• /
• 2009

This study was carried out to evaluate the vertical stress properties in sandy soil according to changes of loading type in soil bin compacted three layers. The following conclusions and comparisons have been made based on careful analysis from theoretical and experimental methods. : When sandy soil subjected to cycle-loading, compression of foundation and diffusion of vertical stress increment(${\Delta}{\sigma}_2$) were influenced by magnitude of loading plate. When sandy soil subjected to reloading after removing of pre-loading, the distribution of ${\Delta}{\sigma}_2$ depth at one time of loading plate width was different from its distribution at more deep point cause of load hysteresis, so in case of design of structure, the effect of ${\Delta}{\sigma}_2$ as depth must be considered. The increment of vertical stress will be different as loading condition and foundation depth, the loading condition must be considered in case of structure design.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.593-597
• /
• 2005

It is generally accepted that fracture toughness of fiber-reinforced polymer composites is affected by loading rate in an atmospheric presure condition. For a present study, the loading rate effect on the fracture toughness of fiber-reinforced laminated composites in the hydrostatic pressure condition was investigated. For this purpose, fracture tests have been conducted using carbon/epoxy composites applying three steps of the strain rate at 270 MPa hydrostatic pressure condition. The loading rates applied were 0.05%/sec, 0.25%/sec, and 0.55%/sec. Fracture toughness was determined from the work factor approach as a function of applied loading rate. The result showed that fracture toughness decreased as the loading rate increased. Specifically, the fracture toughness decreased 12% as the loading rate increased from 0.05%/sec to 0.55%/sec.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.487-490
• /
• 2004

In this paper, we investigated the characteristics of initiation and propagation behavior for fatigue crack observed by changing various shapes of initial crack and magnitudes of loading in modified compact tension shear(CTS) specimen subjected to shear loading. In the low-loading condition, the secondary fatigue crack was created in the notch root due to friction on the pre-crack face grew to a main crack. In the high-loading condition, fatigue crack under shear loading propagated branching from the pre-crack tip. Influenced by the shear loading condition, fatigue crack propagation retardation appeared in the initial propagation region due to the reduction of crack driving force and friction on crack face. In both cases, however, fatigue cracks grew in tensile mode type. The propagation path of fatigue crack under the Mode II loading was 70 degree angle from the initial crack regardless of its shape and load magnitude.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.302-307
• /
• 2004

This paper reviewed characteristics of fatigue crack behavior observed by changing various shapes of initial crack and magnitudes of loading in compact tension shear(CTS) specimen subjected to shear loading. In the high-loading condition, fatigue crack under shear loading propagated branching from the pre-crack tip. Meanwhile, the secondary fatigue crack in the low-loading condition which was created in the notch root due to friction on the pre-crack face grew to a main crack. Influenced by the mode II loading condition, fatigue crack propagation retardation appeared in the initial propagation region due to the reduction of crack driving force and friction on crack face. In both cases, however, fatigue cracks grew in tensile mode type. Propagation path of fatigue crack under the shear loading was 70 degree angle from the initial crack regardless of its shape and load magnitude.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.218-223
• /
• 2001

Many research of elastohydrodynamic lubrication (EHL) has been performed under the condition of steady state loding. However, mechanical elements undergo severe high loads that are fluctuating in general. Conventional numerical method for the circular contact of EHL study has a difficulty in converging the film pressure and thickness especially in high load of steady state. In this work, multigrid multilevel method expels the convergence problem under the condition of high load and very stable convergence is obtained under the dynamic loading condition over 1.0GPa. Several results of dynamic loading condition are shown and compared with those of steady state condition.

• Tribology and Lubricants
• /
• 제25권6호
• /
• pp.367-373
• /
• 2009

Many research of elastohydrodynamic lubrication (EHL) has been performed under the condition of steady state loading. However, mechanical elements undergo severe high loads that are in the fluctuating modes of frequency and amplitude. Conventional numerical method for the circular contact of EHL study has the difficulty in making the film thickness and pressure of EHL converged in high loads of steady state as well as fluctuating loading conditions. In this work, multigrid multilevel method are used for the stable convergence of film pressure and thickness under the conditions of high as well as varying loads, and very stable solutions of film behaviors with elastic deformation are obtained. Several results of dynamic loading condition are shown and compared with those of steady state condition in the aspects of circular EHL film thickness and pressure.

• 한국압력기기공학회 논문집
• /
• 제12권2호
• /
• pp.34-39
• /
• 2016

This paper presents a method to quantify R-ratio effect on J-integral under large-amplitude cyclic loading condition. Generally, monotonic tearing resistance curves are used to assess stability of cracked nuclear piping under seismic loading. However, it is well known that fracture toughness decrease at cyclic loading condition, according to R-ratio. For this reason, it is important to quantify the J-R curves under cyclic loading condition. To quantify the R-ratio effect, correction method which was proposed by Tranchand is considered. This method considers crack opening area in order to calculate modified J-integral. This method leads to an increase of fracture toughness. At R=-0.5 case, this method is good agreement with monotonic J-R curves. However, results show that this method has a limit to apply a large R-ratio case.