• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.232-236
• /
• 2004

The fracture characteristics of unidirectional composite single-lap bonded joints were investigated experimentally and numerically. The effects of bonding method, surface roughness, bondline thickness and the existence of fillet on the failure characteristics and strength of bonded single-lap joints were evaluated experimentally. The failure process, failure mode and the behavior of load-displacement curve was apparently different according to bonding method. The failure load of the specimen co-cured without adhesive was definitely superior to other types of specimens but the specimens co-cured with adhesive film had a less strength than secondary bonded specimens. In the secondary bonded specimens, the lower value of surface roughness and existence of fillet improved the strength of specimens. The strain energy release rates calculated by geometric nonlinear finite element analyses and Virtual Crack Closure Technique for the secondary bonded specimens considering the three types of initial cracks - comer crack, edge crack and delamination crack - were consistent with the test results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.739-740
• /
• 2010

Numerical studies were performed to investigate an effective water cooling type for reducing the thermal load of deflector in test facility with two cooling types and various mass flow rate conditions. According to analyses a core water injection type was superior to a side water injection fro the viewpoint of reducing the thermal load of deflector.

• Journal of Sensor Science and Technology
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2004

Due to various types of errors added to dynamic weight measurement data, proper methods to reduce measurement errors are required to produce reliable weights. To cope with parasitic types of errors in real systems, information provided by the various sensors is utilized and combined in such a way to reduce the measurement errors of load cells. In addition to four channels of load cells from a trailer, an accelerometer is used to obtain the information to compensate the error induced from vertical movement of the vehicle due to the variation of ground level. A model trailer system is run to verify the effectiveness of the proposed method to reduce noise of dynamic weight measurements. Experiments show that the processed error magnitudes of less than 20 g can be obtained for 10 Kg experimental loads.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.157-167
• /
• 2020

The purpose of this study is to analyze the relationship between the occurrence of intermediate peak and time duration, and to conduct a review for the causes of the intermediate peak. In this test, ice impact tests were conducted using a bow side shell frame and ice specimen. A total of 70 samples were manufactured. Two types of ice specimen with relatively different surface conditions were used. The criterion for dividing the two types of ice specimen was the different exposure times to room temperature after freezing. This experiment was conducted for each parameter in order to reproduce the actual icebreaking situation. As a result of the analysis, the intermediate peak in the ice load signal have been found to be caused by mechanisms by which the inner surface of broken ice contact with hull immediately after the initial hitting point of ice has been broken.

• International journal of advanced smart convergence
• /
• v.12 no.2
• /
• pp.167-172
• /
• 2023

In this study, the absolute and relative strength of six upper extremity resistance exercises were measured by classifying resistance exercise experts and non-experts. As a result, the skilled group showed higher absolute and relative muscle strength than the unskilled group in the 6 upper extremity resistance exercises. These results are judged to be the hypertrophy of fast-twith muscles, the mobilization of motor units, and the increase in the speed of nerve conduction while the skilled person consistently performs resistance exercise. Experts use intermuscular coordination efficiently to stably perform the load according to the movement and exercise intensity performed during exercise, whereas the inexperienced person uses relatively large muscle groups rather than efficiently using intermuscular coordination. It is considered that exercise motion and load were performed by mobilizing. In addition, as a result of comparing the absolute and relative muscle strength between the 6 types of upper limb resistance exercises, there was a difference between the 6 types of upper limb resistance exercises in the two groups. It can be judged that greater muscle strength and endurance were created through liver coordination.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.141-147
• /
• 2015

Gas foil thrust bearings (GFTBs) have attractive advantages over rolling element bearings and oil film thrust bearings, such as oil-free operation, high speed stability, and high-temperature operation. However, GFTBs have lower load carrying capacity than the other two types of bearings owing to the inherent low gas viscosity. The load carrying capacity of GFTBs depends mainly on the compliance of the foil structure and the formed hydrodynamic wedge, where the gas pressure field is generated between the top foil and the thrust runner. The load carrying capacity of the GFTBs is very important for the suitable design of oil-free turbomachinery with high performance. The aim of the present study is to identify the characteristics of the load carrying performance of GFTBs. A new test rig for the experimental measurements is designed to provide static loads up to 800 N using a pneumatic cylinder. The maximum operating speed of the driving motor is 30,000 rpm. A series of experimental tests—lift-off test, static load performance test, and maximum load capacity test—estimate the performance of a six-pad GFTB, in terms of the static load, driving torque, and temperature. The maximum load capacity is determined by increasing the static load until the driving torque rises suddenly with a sharp peak. The test results show that the torque and temperature increase linearly with the static load. The estimated maximum load capacity per unit area is approximately 80.5 kPa at a rotor speed of 25,000 rpm. The test results can be used as a design guideline for GFTBs for realizing oil-free turbomachinery.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.3 s.168
• /
• pp.179-186
• /
• 2005

A comparative study of stress distributions in the maxillary bone with three different types of abutment was conducted. Finite element analysis was adopted to determine stress generated in the bone with the different implant systems with micro threads (Onebody type implant, Internal type implant, and External type implant). It was found that the types of abutments and the number of micro threads have significant influence on the stress distribution in the maxillary bone. They were due to the difference in the load transfer mechanism and the size of contact area between abutment and fixture. Also the maximum effective stress in the maxillary bone was increased with increasing inclination angle of load. It was concluded that the maximum effective stress in the bone was the lowest by the internal implant among the maximum effective stresses by other two types of implants and by appropriate number of micro threads, and that the specific number of micro thread was existed to decrease the maximum effective stress in the maxillary bone due to different implant systems and loading conditions.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.79-82
• /
• 2002

The addition of switches to a distribution feeder does, in general, increase reliability by decreasing the duration of the outage of many to the customers on the feeder. To cover its service area so that feeder-level delivery reaches sufficiently close to all customers, feeders typically split their routes many times, in what is often called a lateral feeder. It is interesting to note, however, that the effectiveness of a switch is very much dependent on the types of lateral feeder. The types of lateral are classified into two types. The first is loop lateral feeder that can connect its load to an adjacent feeder through a tie line in case that a fault occurs in its feeder and it is laid out so that every feeder has complete fault backup through re-switching of its loads to other sources like a main feeder. The second is the radial lateral feeder cannot connect its load to an adjacent line, no provision is made for contingency backup of feeders. There are no other circuits in the radial lateral feeder form which to restore power. In this study, we evaluate the effectiveness of a switch installation between on the radial and loop lateral feeders to increase reliability by decreasing the duration of the outage. These results can help power utility to design the switch layouts on the radial and loop lateral feeder system.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.1
• /
• pp.96-105
• /
• 2013

This study aims to investigate the energy performance of apartment in respect of complex design, building type and generation house layout and finally to produce the guide line for energy saving design. To grasp the present condition and problem about this subject, apartment building types were examined and representative types were extracted. Considering azimuth angle, private area, and generation number, building type of the subject apartment was classified in detail, energy simulation was conducted, and the effect to energy cost was compared. In the research, using VE energy simulation program, the heating and cooling load were calculated and converted to energy cost. It is expected that this analysed results will be basic data for the more integrated study. Research consequence can be summarized as follow: 1) Energy cost is compared according to several azimuth in plank '一' type apartment. As the results, calculated gas cost is the best in $49^{\circ}$, but total cost is in $-31^{\circ}$. 2) Apartment buildings of tower types are compared, it is resulted that 'Y' type (azimuth $-7^{\circ}$, $-20^{\circ}$) is the best in gas cost, but the total cost is worst because of high cooling load.

• Journal of Intelligence and Information Systems
• /
• v.12 no.2
• /
• pp.83-98
• /
• 2006

When unit loads are stacked in multiple tiers, as the number of tiers increases, the space consumption per unit load decreases; at the same time, the number of relocations during retrieval operations increases. This study derives formulas fur estimating the expected number of relocations for retrieving a random unit load from various types of stacks with different combinations of the number of rows, the number of columns, and the number of tiers. Based on the derived formulas, the handling cost and the space cost of the different types of stacks are compared with each other.