• 한국정보통신학회논문지
• /
• 제20권9호
• /
• pp.1763-1770
• /
• 2016

본 논문에서는 넓은 출력 부하 전력에서도 동작하는 하이브리드 변환기를 제안했다. 스위치드 커패시터 변환기는 높은 부하 전력에서 효율이 낮고, 낮은 부하 전력에서는 효율이 높다. 반대로, 벅 변환기는 높은 부하 전력에서는 효율이 높고, 낮은 부하 전력에서는 효율이 낮다. 제안된 하이브리드 변환기는 스위치드 커패시터 변환기와 벅 변환기를 혼합했다. 낮은 부하 전력에서는 스위치드 커패시터 변환기를 동작시키고, 높은 부하에서는 벅 변환기를 동작시켜, 넓은 출력 부하 전력에서 전력 효율을 향상시켰다. 제안된 하이브리드 변환기는 $0.18{\mu}m$ CMOS 공정으로 구현되었다. 하이브리드 변환기의 출력 부하 전력 범위는 0.05~100mW 이며, 벅 변환기와 스위치드 커패시터 변환기에서 각각 93%와 77%의 최대 전력 효율을 가진다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.7-10
• /
• 2001

This paper provides a solution for the problem of efficiency decrease caused by load variation. A novel control scheme of tracking the PT's operation frequency for the maximum efficiency is proposed. As a result, a high efficiency over $80\%$ has been achieved even under the output-current decrease down to $10\%$ of the full load current.

• 대한전기학회논문지
• /
• 제31권7호
• /
• pp.25-30
• /
• 1982

This paper considered the energy saving problem of D.C. motor in arbitrary load condition. We can improve efficiency by maintaining the proper ratio of armature current/field current. First, the condition of maximizing the efficiency was obtained, and then the real time control was implemented by using microprocessors. As a result, the efficiency was improved in spite of constant output. For example, the efficiency at 1/5 load was improved from 56.7% to 80%.

• 한국전자통신학회논문지
• /
• 제10권8호
• /
• pp.945-952
• /
• 2015

GaN 전력증폭소자를 이용한 전력증폭기의 고효율 특성을 구현하기 위하여 $50{\Omega}$으로 정합된 전력증폭소자는 적용 주파수 대역, 출력전력, 효율 특성 선정의 한계가 있으므로 본 연구에서는 source/load-pull 시험을 통한 측정 데이터를 기반으로 고출력, 고효율 특성의 설계 목적에 맞는 정량적 입력 및 출력 임피던스를 추출하여 고효율 전력증폭기를 구현하였다. 구현된 전력증폭기는 2.7-3.1GHz의 주파수 대역에서 25watt(44dBm), 66-76%의 PAE특성 나타낸다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.290-297
• /
• 2002

This paper presents analysis results for the effect of power control strategies on the part load performance of gas turbine based power generation systems utilizing exhaust heat of the gas turbine such as cumbined cycle power plants and regenerative gas turbines. For the combined cycle, part load efficiency variations were compared among different single shaft gas turbines representing various technology levels. Power control strategies considered were fuel only control and IGV control. It has been observed that gas turbines with higher design performances exhibit superior part load performances. Improvement of part load efficiency by adopting air flow modulation was analyzed and it is concluded that since the average combined cycle performance is affected by the range of IGV control as well as its temperature control principle, a control strategy appropriate for the load characteristics of the individual plant should be adopted. For the regenerative gas turbine, it is likewise concluded that maintaining exhaust temperature as high as possible by air flow rate modulation is required to increase part load efficiency.

• 한국유체기계학회 논문집
• /
• 제6권3호
• /
• pp.28-35
• /
• 2003

This paper presents analysis results for the effect of power control strategies on the part load performance of gas turbine based power generation systems utilizing exhaust heat of the gas turbine such as combined cycle power plants and regenerative gas turbines. For the combined cycle, part load efficiency variations were compared among different single shaft gas turbines representing various technology levels. Power control strategies considered were fuel only control and IGV control. It has been observed that gas turbines with higher design performances exhibit superior part load performances. Improvement of part load efficiency of the combined cycle by adopting air flow modulation was analyzed and it was concluded that since the average combined cycle performance is affected by the range of IGV control as well as its temperature control principle, a control strategy appropriate for the load characteristics of the individual plant should be adopted. For the regenerative gas turbine, it is likewise concluded that maintaining exhaust temperature as high as possible by air flow rate modulation is required to increase part load efficiency.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권4호
• /
• pp.493-500
• /
• 2015

A flyback converter operates with either pulse width modulation (PWM) or pulse frequency modulation (PFM) control scheme depending on the load current. At light load condition, PFM control is employed to reduce the switching frequency and thereby minimize the switching power loss. For heavier load, PWM control is used to regulate the output voltage of the flyback converter. The flyback controller has been implemented in a $0.35{\mu}m$ BCDMOS process and applied to a 40-W flyback converter. The light-load power efficiency of the flyback converter is improved up to 5.7-% comparing with the one operating with a fixed switching frequency.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.279-282
• /
• 2005

Recently, due to the launching of digital broadcasting service, a demand of PDP TV with large screen size is sharply rising. PDP power module is mainly divided into power factor correction (PFC) stage and sustaining power stage. Especially, sustaining power module has pulsating load characteristics. So, the hard switching at light load condition causes low efficiency and thermal problem. Therefore, a new power conversion circuit for sustaining power module of 60' PDP is proposed whose ZVS is obtained by additional ZVS tank. This paper presents properties of the proposed converter through mode analysis, numerical analysis. And a 900w prototype for sustaining power module of 60' PDP is produced to verify the analytic results. As an experimental results, ZVS is achieved from full load to 10% load variation and more than 92% of high efficiency is obtained at 10% load condition.

• 한국수소및신에너지학회논문집
• /
• 제13권4호
• /
• pp.304-312
• /
• 2002

In this study, the performance of the $5Nm^3/hr$ compact type steam reformer which was developed for application of fuel cell or hydrogen station was evaluated in terms of gas process efficiency. For these purposes, reforming efficiency and total efficiency with system load change were analyzed. The reforming efficiency was calculated from the total molar flow of hydrogen output over total fuel flow input to the reformer and the burner on the higher heating value(HHV). In the case of the total efficiency, recovered heat at the heat recovery exchanger was considered. From the results, it was known that system performance was stable, because methane conversion showed the a slight decline which is about 2% though increasing system load to full. Reforming efficiency was increased from 20% to 58%, respectively as increasing system load from 10% to 90%. It was found that total efficiency was higher then reforming efficiency because of terms of heat recovered. As a results, it was known that total efficiency was increased form 75% to 83% at the 10% and 90% system load, respectively. From these results, it is concluded that compact steam reformer which is composed of stacking plate-type reactors is suitable to on-site hydrogen generator or to fuel cell application because of quick start within 1 hr and good performance.

• 한국화재소방학회논문지
• /
• 제25권1호
• /
• pp.1-6
• /
• 2011

고층건축물에서의 피난효율과 수용인원 산정기준의 문제점을 확인하기 위하여 피난 시뮬레이션을 수행하였다. 지상 39층 주상복합 건축물의 계단폭이 각각 1.2m, 1.5m, 1.8m일 때, 피난시간과 피난자수를 Simulex로 계산하였다. 소방법 기준으로 산정한 총수용인원은 실거주자의 2.3배, NFPA 101 인명구조코드 기준의 2.6배였다. 소방법 기준의 경우, 계단폭이 작을수록 증간층에서의 병목현상으로 인해 피난효율이 낮았지만, 실거주나 NFPA 기준에서는 피난효율이 높고 계단폭이 피난효율에 미치는 영향이 미미함을 확인하였다. 소방법 기준을 적용할 때 계단폭이 1.8m에서도 병목현상이 일어나지만, 실거주 또는 NFPA 기준을 적용할 때는 계단폭 1.2m에서도 안전한 것으로 나타 남에 따라 수용인원 산정관련 소방법 기준의 완화가능성에 대한 추가연구가 필요하다.