• 대한전기학회논문지:전력기술부문A
• /
• 제51권2호
• /
• pp.45-52
• /
• 2002

Load modeling is classified into two methods according to approaching method, so called the measurement and component-based method. The measurement method is to model the load characteristics measured directly at substations and feeders. But it is difficult to measure continuously load characteristics from naturally occurring. system variation. The component-based method consists of the fellowing process; component load modeling, composition rate estimation and aggregation of component loads, etc. In this paper, the characteristic experiment of component loads was performed to obtain data for the component load modeling as the component-based method. At first, representative component loads were selected by the proposed method considering the accuracy of load modeling and the performance possibility of component load experiment in the laboratory. Also an algorithm was Proposed to identify the reliability of data obtained from the component load characteristic experiments. In addition, the results were presented as the case studies.

• 전기학회논문지P
• /
• 제54권2호
• /
• pp.101-107
• /
• 2005

The reduced power quality due to some of disturbances on power system has great influence on the efficient and life of load for bad with serious economic loss. The response of load about disturbance needs to analysis quantitatively in detail to improve load characteristics. In this research, a power supply device is developed to supply disturbed power similar to that of power system. The developed device can output a voltage and frequency from 180[V] to 240[V], 55[Hz] to 65[Hz] respectively. The most outstanding feature of this device is a function to be performed steady and dynamic state characteristic experiment on load or appliances. Also, this device is designed to include high accuracy ouput and simple measurement.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.83-85
• /
• 2006

In this paper, the dynamic characteristic according to variable load of Permanent magnet Linear Synchronous Motor(PMLSM) is dealt with carefully. And the experiment machine is manufactured for analysis of dynamic characteristic. The results of both simulation and experiment are discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.363-365
• /
• 2002

The characteristic responds of load respect to various disturbances which can usually be occurred on actual power system is very important to analyze performance and to improve load with high-technology. The disturbance power supply is designed to provide wide range of power to testing load. This device uses PLC technology to dynamic characteristic experiment and CVVF to change frequency. Also this instrument includes data acquisition system to obtain reliable data from experiment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.325-327
• /
• 1999

In this research, selection of component load and measurement device is considered for accurate component load modeling. The procedure of component load characteristic experiments is also presented.

• 전기학회논문지
• /
• 제57권4호
• /
• pp.596-602
• /
• 2008

This paper presents the dynamic characteristic analysis of Permanent Magnet Linear Synchronous Motor(PMLSM) according to variable load. In order to analyze dynamic characteristics, finite element method(FEM) was used for calculation of the parameter and the Matlab simulink was used for dynamic characteristic simulation. The measuring system of the dynamic characteristics was manufactured and the experiment results were compared with the simulation results.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.153-158
• /
• 2013

The purpose of this study is to investigate the performance characteristics of the counterflow exhaust heat recovery device for the applied gasoline engines. The EHRS device is installed behind the catalyst. This study investigates the engine warm-up characteristic, the exhaust noise characteristic, the back-pressure characteristic. The engine warm-up characteristics is (load 0%, load 10%, load 20%) in (idle, 1000rpm, 1500rpm, 2000rpm, 2500rpm) conditions by measuring the time it warmed up, coolant temperature ($25^{\circ}C{\sim}80^{\circ}C$) until the performance evaluation is performed. The wide open throttle and the coast down the exhaust noise and the back-pressure characteristic experiment repeated twice. The test conditions is 950rpm~6,050rpm proceed experiment repeated 3-5 times. Load 0% idle conditions except the results improved engine warm-up characteristics. The exhaust noise obtain similar results the BASE+EHRS W/O_FRT_MUFF with BASE and back-pressure to obtain similar results BASE+EHRS W/O_FRT_ MUFF with BASE+EHRS.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.193-196
• /
• 2001

This paper deals with the fabrication and characteristic experiment of a high-Tc superconducting(HTSC) power supply using by Bl-2223 tape. The purpose of this research is to apply real HTSC load. This system consists of two heaters, an electromagnet, a Bi-2223 solenoid and a Bi-2223 pancake load. In the experiment. 17sec and 8.5sec were used for pumping period. Mechanism of the superconducting switch is used for heater-trigger. In experiment, the pumping-current has reached about 1.2A.

• 한국산학기술학회논문지
• /
• 제7권6호
• /
• pp.1092-1099
• /
• 2006

본 논문에서는 유도전동기를 인버터와 같은 전력변환장치를 사용하여 정상상태의 동작특성은 물론 과도특성까지 해석하기 위해서는 유도전동기와 부하를 포함하는 전체 시스템의 정확한 동적 모델링을 이용하여 시스템 방정식으로 표현해야 한다. 또한 최대 견인력 제어를 위해서 속도센서리스벡터제어와 부하 토크 외란 관측기를 통하여 점착력 계수를 추정한다. 이와 같은 시스템의 제어 알고리즘을 구현하기 위하여 철도 모의 장치를 이용하여 제안된 알고리즘을 시뮬레이션과 실험을 통하여 확인하고, 철도 차량의 속도 가감에 따른 공전속도에 대한 점착력의 관계 등 제반 사항을 모의 장치에 의해서 구현하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.403-408
• /
• 2005

In recent years, vehicle accessories substitute steel for aluminum. But, subframe play a important role of vehicle safety. Therefore, dynamic characteristic of steel subframe is understood at real vehicle. And this is able to apply dynamic characteristic of Aluminum. At this paper, we confirm dynamic load that is operated Steel subframe with experiment And result of finite element analysis which is operated dynamic load is compared with result of experiment.