• Journal of the Korean institute of surface engineering
• /
• v.55 no.4
• /
• pp.231-235
• /
• 2022

As environmental pollution becomes more serious, the demand for electric vehicles (EVs) and lithium-ion batteries for electric vehicles is rapidly increasing worldwide. Accordingly, the amount of waste batteries is also increasing, and a technology for recycling and reusing them is required. In order to reuse a used battery, it is necessary to non-destructively diagnose the deterioration condition of the battery. Therefore, in this study, we investigate the diagnosis of degradation for parallel-connected lithium-ion battery cells through non-constructive electrochemical approach. As the number of parallel-connected cells increased, in addition to linear degradation, abrupt step-like degradation occurred, which is attributed to the predominant degradation of specific cells. In addition, it is confirmed that deteriorated cells among multiple cells can be distinguished through a simple measurement of open circuit voltage (OCV).

• Journal of Electrochemical Science and Technology
• /
• v.4 no.1
• /
• pp.27-33
• /
• 2013

The consequences of electrode density and thickness for electrochemical performance of lithium-ion cells are investigated using 2032-type coin half cells. While the cathode composition is maintained by 90:5:5 (wt.%) with $LiCoO_2$ active material, Super-P electric conductor and polyvinylidene fluoride polymeric binder, its density and thickness are independently controlled to 20, 35, 50 um and 1.5, 2.0, 2.5, 3.0, 3.5 g $cm^{-3}$, respectively, which are based on commercial lithium-ion battery cathode system. As the cathode thickness is increased in all densities, the rate capability and cycle life of lithium-ion cells become significantly worse. On the other hand, even though the cathode density shows similar behavior, its effect is not as high as the thickness in our experimental range. This trend is also investigated by cross-sectional morphology, porosity and electric conductivity of cathodes with different densities and thicknesses. This work suggests that the electrode density and thickness should be chosen properly and mentioned in detail in any kinds of research works.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.27 no.2
• /
• pp.265-270
• /
• 2013

Dialysis is the rate-limiting step in the preparation of aqueous silk fibroin (SF) solution. However, the traditional practice of dialyzing SF solution for at least 48 h to remove LiBr is not based on empirical evidence. The aim of the present study was to systematically measure LiBr content in SF solutions dialyzed for varying lengths of time and assess the potential toxicity of residual lithium ions in cells. Complete removal of lithium ions was not achieved even after 72 h of dialysis, with a residual lithium ion content in the solution of 22.85 mg/l. SF films prepared from solutions dialyzed for 8 and 24 h had predominantly random coil or b-sheet structures, respectively. The residual lithium had little cytotoxicity in NIH3T3 fibroblast cells, but viability was compromised in cells grown on SF film prepared from solution dialyzed for 24 h.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.339-340
• /
• 2012

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.472-480
• /
• 2009

In this paper, a charge equalization converter with parallel-connected primary windings of transformers is proposed. The proposed work effectively balances the voltage among Lithium-Ion battery cells despite each battery cell has low voltage gap compared with its state of charge (SOC). The principle of the proposed work is that the equalizing energy from all battery strings moves to the lowest voltage battery through the isolated dc/dc converter controlled by the corresponding solid state relay switch. For this research a prototype of four Lithium-Ion battery cells is optimally designed and implemented, and experimental results show that the proposed method has excellent cell balancing performance.

• Journal of Power Electronics
• /
• v.10 no.2
• /
• pp.210-217
• /
• 2010

This paper introduces a lithium ion battery management system (BMS) for the STSAT-3 satellite. The specifications of a lithium ion battery unit are proposed to supply power to the satellite and the overall electrical and mechanical designs for a lithium ion battery management system are presented. The structural simulation results will be shown to confirm the behavior of both the BMS and the cells.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.775-780
• /
• 2013

In general, the battery module of an electric vehicle (EV) consists of lithium-ion cells. A lithium-ion battery is a secondary rechargeable battery, and it consists of numerous stacked plates that serve as electrodes and separators. Owing to these microstructural features, its numerical analysis is very expensive. Therefore, this study aims to present a simplified thermal analysis model using equivalent thermal properties, and we compare the experimental results with numerical results for 185.3Ah and 20Ah cells. Furthermore, we show the thermal behavior of cells without the finite element method (FEM) or finite volume method (FVM) by adopting the lumped capacitance method (LCM).

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.17 no.4
• /
• pp.46-58
• /
• 2021

As accidents with thermal runaway (TR) of lithium-ion batteries occur sporadically, the safety concern is the main obstacle that hinders the large-scale applications of lithium ion batteries. In most accidents, the TR of a single cell occurred first, and then dissipated the heat to the surroundings and triggered the TR of adjacent cells, resulting in TR propagation. Therefore, it is important to understand the mechanism of TR propagation and determine the key parameters during TR propagation in a battery pack. In this study, we performed a numerical analysis on the thermal runaway phenomenon by cathode active materials and appearance sizes in cylindrical lithium-ion batteries using a two-dimensional analysis model. The model results showed that the TR propagation of 21700 type cells (21 mm diameter, 70 mm height) occurs more rapidly than 46800 type cells (46 mm diameter, 80 mm height) and the LFP cell has higher thermal safety than the NCM cell. Especially, we found that the effect of the separator on the occurrence of TR is negligible.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.1
• /
• pp.68-74
• /
• 2005

In this work, polymerization conditions of the gel polymer electrolyte (GPE) were studied to obtain better electrochemical performances in a lithium-ion polymer battery. When the polymerization temperature and time of the GPE were 70$^{\circ}C$ and 70 min, respectively, the lithium polymer battery showed excellent a rate capability and cycleability. The TMPETA (trimethylolpropane ethoxylate triacrylate)/TEGDMA (triethylene glycol dimethacrylate)-based cells prepared under optimized polymerization conditions showed excellent rate capability and low-temperature performances: The discharge capacity of cells at 2 Crate showed 92.1 % against 0.2C rate. The cell at -20 $^{\circ}C$ also delivered 82.4 % of the discharge capacity at room temperature.

• Journal of Electrochemical Science and Technology
• /
• v.6 no.1
• /
• pp.26-33
• /
• 2015

In this study, cell performance and thermal stability of lithium-ion cells with a polyimide (PI) separator are investigated. In comparison to conventional polyethylene (PE) separator, the PI separator exhibits distinct advantage in microporous structure, leading to superior reliability of the cell. The cells with PI separator exhibit good cell performances as same as the cells with PE separator, but their reliability was superior to the cell with PE separator. Especially in the hot-box test at 150 and 180℃, PI separator showed a contraction percentage close to 0% at 150℃, while the PE separator showed a contraction percentage greater than 10% in both width and length. Therefore, the PI separator can be the promising candidate for separators of the next generation of lithium-ion battery.