• 한국분무공학회지
• /
• 제20권3호
• /
• pp.175-180
• /
• 2015

A series of sprinkler discharging tests was conducted to measure the droplet size and its distribution of residential fire sprinkler heads. Droplet sizes in sprinkler spray were measured using a laser diffraction method for the flush, circular and pendent type sprinkler head. In this study, the $D_{v,50}$ of the flush type sprinkler heads were ranged between $530{\sim}1040{\mu}m$ and those of circular and pendent type were $988{\mu}m$ and $916{\mu}m$, respectively. The measured cumulative volume distributions were followed by a combination of the log-normal and Rosin-Rammler distribution which is widely used in the computational fire analysis and the parameters of distribution function were obtained from the best fit line through the measured data.

• 대한기계학회논문집
• /
• 제19권2호
• /
• pp.418-426
• /
• 1995

A bubble-powered microactuator is designed conceptually. And the actuation mechanism due to bubble growth and collapse is studied numerically and analytically. In this analysis, it is estimated that the time lag for bubble formation on micro line heater, the duration of the bubble growth and collapse and the pressure change in actuator due to the bubble evolution. Based on these calculations, the actuator control scheme is visualized. This actuator may be applicable to the system which needs to pump liquid correctly and regularly.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권4호
• /
• pp.459-465
• /
• 2009

This paper considers the influence of internal heat exchangers to the efficiency of a refrigerating system. These internal heat exchangers(liquid-suction or suction-line heat exchangers) can, in some cases, yield improved system performance while in other cases they degrade system performance. A steady state mathematical model is used to analysis the performance characteristics of refrigeration system with internal heat exchanger. The influence of operating conditions, such as gas cooler pressure and evaporation temperatures, superheat in the evaporator and temperature of gas cooler outlet, to optimal dimensions of the heat exchanger is also analyzed in the paper. The main results were summarized as follows : the mass flowrate of R744, inner diameter tube and length of internal heat exchanger, and effectiveness have an effect on the cooling capacity, compressor work and RCI(Relative capacity index) of this system. With a thorough grasp of these effect, it is necessary to design the R744 compression refrigeration cycle using internal heat exchanger.

• 동력기계공학회지
• /
• 제11권3호
• /
• pp.41-46
• /
• 2007

The microstructure and electrochemical analysis of welds of electric resistance welding(ERW) pipe were investigated. The direction of metal flow line in HAZ of ERW pipe shifted to the inner(or outer) surface of pipe by plastic deformation during welding. The lowest heat input welds of ERW pipe was showed crack by liquid penetrant testing. Accelerated corrosion test by constant current density of 20mA/$cm^{2}$ developed groove at the welds of ERW pipe and the measured grooving factors were about $1.2{\sim}1.5$. Corrosion potential of base metal obtained by cyclic polarization in artificial sea water(3.5wt.% NaCl solution) was 100mV higher than that of weld metal of ERW pipe.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.854-861
• /
• 1998

The demand of LNG as a cheap and clean energy which does not cause an environmental problem has sharply been increased in Korea. In general LNG is stored in a cargo tank specially designed as a liquid state below $-162^{\circ}C$. The main engine of a LNG carrier is generally a steam boiler because LNG is a highly flammable fluid with the possibility of explosion. The main engine of a cargo ship has to be capable of the propulsion load and various auxiliary loads for the safe navigation since it is the primary energy source. Therefore the evaluation of a main boiler's energy capacity is a key design point in the planning of LNG carrier's construction. This research is to develop the computational program for the analysis of steam boiler Heat balance for LNG carrier.

• 대한기계학회논문집B
• /
• 제33권5호
• /
• pp.373-380
• /
• 2009

The evaporation process of multi-component fuel is different from one of a single component, because the properties of each component affects among the components. In actual engine, the spatial distribution of fuel vapor concentration dominates auto-ignition and initial combustion, and depends on the volatility and diffusivity of each component fuel contained in the multi-component fuel. Then, this study proposes a simplified numerical scheme for analysis of evaporation process of multi-component fuel sprays. Evaporation process is calculated by KIVA-II code based on the simple two-phases region that is approximated by modified saturated liquid-vapor line, which was obtained by connecting the 50% distillation temperature for each component under several pressure fields. Consequently, it can be quantitatively simulated that vapor of low boiling fuel component mostly exists around nozzle and spray tip region, the high boiling duel component, on the other hand, mostly appears near the spray tip.

• 한국공작기계학회논문집
• /
• 제15권3호
• /
• pp.32-38
• /
• 2006

During stereolithography processes, the shape errors such as curl distortion and distortion of side face are generated due to the shrinkage of liquid resins. In this study, the effects of dimension of part and structure of supports on the shape error are examined. Cubic specimens which have different thicknesses are manufactured and their deformations are measured with CMM. Thicker part generates smaller curl distortion of top face and larger of bottom face. Also thicker part generates larger distortion of side face until part thickness increases to about 20mm. Larger stiffness of supports which is obtained by shorter spacing of the supports and line type contact instead of point type contact generates smaller shape error of the part.

• 드라이브 ㆍ 컨트롤
• /
• 제10권3호
• /
• pp.7-13
• /
• 2013

Hydraulic vane pumps are widely used in various hydraulic systems because of its compactness and light weight. It is well known that the vanes and cam ring are separated by very thin liquid films which result in the EHL state. Contrary to the case of cylindrical roller bearings, the inlet and side boundary pressures are much higher than the atmospheric pressure. In this paper, a numerical solution of the EHL of finite line contacts between the cam ring and vane tip with profiled ends is presented. Using a finite difference method with non-uniform grids and the Newton-Raphson method, converged solutions are obtained for moderate load and material parameters. The EHL pressure distribution and film shape are considerably affected by pump delivery pressure and the side boundary condition applied. Both the maximum pressure and the minimum film thickness always occurred near the edge regions. The present results can be used in the design of optimum vane profile in hydraulic vane pump.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 춘계학술발표대회 논문집
• /
• pp.103-108
• /
• 1999

A synthesized model of pultrusion process considering thermally induced deformatiion was established. The model was composed of liquid resin flow model thermo-chemical analysis and linear elastic analysis. in order to verify the above-mentioned models several experiments were performed. A laboratory scale pultrusion line was established and glass/polyester composites were fabricated. the experimental results were compared with the calculated ones. The model successfully could estimate degree of cure pulling force and amount of process-induced deformation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.48-53
• /
• 2004

Injection molded plastic parts have many surface defcts: Warpage, wedline, flowmark, zetting, scratching, shading and so on. In the desktop mnitor's case, Weld line have been one of the main surface defects. Nowadays in the pursuit of light weight of parts, one of the big problems of LCD Monitor thinks Warpage and surface shrinkage. In this paper, we introduce some instances for prevevting these defestcs in the side of mould drawing, parts drawing and processing condition. Based on these, we tried to find out the optimum processing conditions through repeatedly tried injection moulding after reflecting these instances.