• Korea-Australia Rheology Journal
• /
• 제19권1호
• /
• pp.17-25
• /
• 2007

In liquid composite molding (LCM), composites are produced by impregnation of a dry preform with liquid resin. The resin flow through the preform is usually described by Darcy's law and the permeability tensor must be obtained for filling analysis. While the resin flow in the thickness direction can be neglected for thin parts, the resin flow in the transverse direction is important for thicker parts. However, the transverse permeability of the preform has not been investigated frequently. In this study, the transverse permeability was measured experimentally for five different fiber preforms. In order to verify the experimental results, the measured transverse permeability was compared with numerical results. Five different fiber mats were used in this study: glass fiber woven fabric, aramid fiber woven fabric, glass fiber random mat, glass fiber braided preform, and glass/aramid hybrid braided preform. The anisotropic braided preforms were manufactured by using a three dimensional braiding machine. The pressure was measured at the inlet and outlet positions with pressure transducers.

• Elastomers and Composites
• /
• 제55권4호
• /
• pp.289-299
• /
• 2020

Highly aromatic (HA) oils are common processing aids used in tire tread compounds. However, they often bleed and evaporate from the vulcanizates during tire use. Thus, the mechanical and dynamical properties of the tire decrease. To overcome this problem, we investigated nonfunctionalized liquid butadiene rubber (LBR-305, Kuraray) and center-functionalized liquid butadiene rubber (C-LqBR), polymerized by anionic polymerization. In addition to the liquid butadiene rubbers, p-tert-octylphenol (P-Resin) and C5 hydrocarbon (H-Resin) tackifier resins, which can induce entanglement of rubber compounds, were researched as a processing aid to solve the bleeding problem. Liquid butadiene rubbers have significantly reduced extraction loss by crosslinking with the main rubber chain. They have also increased the abrasion resistance and showed similar or better mechanical and dynamical properties against HA oils. However, resin compounds did not show differences in extraction loss compared to HA oil compounds; instead, they showed increased wet traction.

• 한국가구학회지
• /
• 제21권2호
• /
• pp.126-132
• /
• 2010

High wear resistances are obtained with an additional coating of the surface of the decor film in the same operation of impregnating with low viscosity melamine resin by liquid overlay system. The cellulosic fibers have a good adhesion to the corundum particles and keep them sufficiently homogeneous in the blend with the resin. The amount of these fibers in nearly as big as it is in a common overlay in relation to the resin. Therefore these fibers keep the resin inside during the press process and consequently very the surface of the decor print of the film. That means that the corundum particles are equally dissipated throughout the entire layer over the decor. The change of the color of the print is nearly not visible as the particles are almost equally dissipated. Looking to the flooring purposes of liquid overlay one can see that by the lesser exposure of the corundum particles on the very surface, there is no longer an abrasive surface but a feeling like a normal melamine surface.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.371-376
• /
• 2001

The purpose of this study is to investigate toughening of unsaturated polyester resin by addition of polyuretane liquid rubber. In general, unsaturated polyester resin has strong brittleness in spite of its high strength Therefore; it is difficult to use unsaturated polyester mortar for the place where impact resistance is demanded. In this study, it was evaluated strength and Gf by using to polyurethane liquid rubber. As a result, the toughness of unsaturated polyester mortar was increased by polyuretane liquid rubber.

• 농업생명과학연구
• /
• 제46권2호
• /
• pp.43-48
• /
• 2012

거대억새 자원의 활용도 제고방안의 일환으로 거대억새 파티클을 이용하여 보드를 제조하고 수지첨가량, 수지타입 및 밀도에 따른 물성을 검토하였다. 흡수율은 보드의 밀도 및 수지첨가량이 증가할수록 감소하였으며, 휨강도와 박리강도는 밀도 및 수지 첨가량이 증가할수록 파티클간 결합력이 강해져 증가하였다. 두께 팽창률은 보드의 밀도가 증가함에 따라 증가하였고 수지 첨가량이 많을수록 감소하였다. 수지타입에 따라 두께 팽창률과 흡수율은 액상 페놀수지로 제조한 보드가 더 나은 치수안정성을 보였고, 보드밀도 $0.4g/cm^3$ 로 제조한 경우 수지 첨가율 11~13% 일 때 휨강도는 분말상 및 액상 페놀수지 간에 차이가 없었으며, 박리강도는 액상의 페놀수지로 제조한 보드가 더 좋은 값을 나타내었다.

• 공업화학
• /
• 제18권5호
• /
• pp.527-530
• /
• 2007

방염도료로 일액형 염화고무(Chlorinated Rubber) 백색도료가 많이 사용되고 있는데 이는 탄화시 검은 연기가 많이 발생되고 목재에 대한 표면강도와 접착력 등의 미흡한 단점이 있어 이러한 점 등을 고려한 Polyurethane Resin계(Alkyd Resin) 이액형 방염우레탄라카 백색도료를 개발하였다. 본 실험에서 개발한 목재용 Polyurethane Resin계 방염도료 조성의 물성은 기존의 방염백색도료보다 목재와의 친화력이 향상되고 다량의 연기발생은 억제하는 결과를 얻었다.

• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.33-39
• /
• 2010

The moisture absorption properties such as diffusion coefficient and moisture content ratio of liquid type epoxy resin systems with the filler were investigated. Bisphenol A type and Bisphenol F type epoxy resin, Kayahard MCD as hardener and 2-methylimidazole as catalyst were used in these epoxy resin systems. The nano-sized spherical type fused silica as filler were used in order to study the moisture absorption properties of these liquid type epoxy encapsulant according to the change of filler size. The temperature of glass transition (Tg) of these epoxy resin systems was measured using Dynamic Scanning Calorimeter (DSC), and the moisture absorption properties of these epoxy resin systems according to the change of time were observed at $85^{\circ}C$ and 85% relative humidity condition using a thermo-hygrostat. The diffusion coefficients in these systems were calculated in terms of modified Crank equation based on Ficks' law. An increase of Tg and diffusion coefficient with filler size in these systems can be observed, which are attributed to the increase of free volume with Tg. The change of maximum moisture absorption ratio according to the filler size and filler content cannot be observed; however, the diffusion coefficients of these systems decreased with filler content. The diffusion via free volume is dominant in the epoxy resin systems with low nano-sized filler content; however, the diffusion with the interaction of absorption according the increase of the filler surface area is dominant in the liquid type epoxy encapsulant with high nano-sized filler content.

• 대한심미치과학회지
• /
• 제29권2호
• /
• pp.92-102
• /
• 2020

Bond-Fill SB는 분말 / 액체로 만들어져 있으며, 브러시의 액량을 조절하여 유동성을 조절할 수 있습니다. TBB라고하는 강력한 촉매 덕분에 물과 산소가있는 상태에서도 중합이 가능하다는 장점이 있습니다. 또한 4-META를 함유하고있어 적절한 표면 처리로 금속 및 세라믹에 접착 할 수있는 장점이 있습니다. 이러한 장점을 충분히 이해하시면 기존의 복합 레진으로 처리하기 어려운 경우에 적극 활용할 수 있습니다.

• Journal of the Korean Wood Science and Technology
• /
• 제42권5호
• /
• pp.605-614
• /
• 2014

This study investigated microstructural changes of cured urea-formaldehyde (UF) resins mixed with aqueous rubber latex emulsion after intentional acid etching. Transmission electron microscopy (TEM) was used in order to better understand a hydrolytic degradation process of cured UF resins responsible for the formaldehyde emission from wood-based composite panels. A liquid UF resin with a formaldehyde to urea (F/U) molar ratio 1.0 was mixed with a rubber latex emulsion at three different mixing mass ratios (UF resin to latex = 30:70, 50:50, and 70:30). The rate of curing of the liquid modified UF resins decreased with an increase of the rubber latex proportion as determined by differential scanning calorimetry (DSC) measurement. Ultrathin sections of modified and cured UF resin films were exposed to hydrochloric acid etching in order to mimic a certain hydrolytic degradation. TEM observation showed spherical particles and various cavities in the cured UF resins after the acid etching, indicating that the acid etching had hydrolytically degraded some part of the cured UF resin by acid hydrolysis, also showing spherical particles of cured UF resin dispersed in the latex matrix. These results suggested that spherical structures of cured UF resin might play an important role in hindering the hydrolysis degradation of cured UF resin.

• Elastomers and Composites
• /
• 제31권1호
• /
• pp.13-22
• /
• 1996

In order to Improve the fracture toughness of epoxy resin system, liquid chloroprene rubber(LCR) and liquid butadiene rubber (LBR) which have hydroxy group were used in the brittle epoxy system. Mechanical and toughness characterization of the modified epoxy resins were investigated as a function of liquid rubbers content. Epoxy resins modified with both of the liquid rubbers showed complete phase-separation microstructure : In all of the LCR content, it was observed that the domain size of LCR dispersed in the epoxy matrix ranging from $2{\mu}m\;to\;5{\mu}m$. It was found that fracture toughness, $K_{ic}$, of the modified LCR system was enhanced continuously as increasing LCR content. However around 10phr of LBR system showed maximum fracture toughness. Specifically, when BPA add to the modified LCR system, thermal and mechanical properties increased than neat epoxy. At the same time, fracture toughness was enhanced.