• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.89-96
• /
• 2001

A concrete lining of NATM tunnel is the final product of a process that involves planning and evaluation of user needs, geotechnical investigations, analysis of ground-lining interaction, construction, and observations and modifications during construction. The designer must consider the lining in context of the many function, construction, and geotechnical requirements. Also, the loss of supporting capacity of shotcrete lining due to poor rock qualities and shotcrete erosion must be considered. The values, shapes, and estimating methods of rock load and water pressure are very different with every designers. Estimating methods of rock loads used in the design of NATM tunnel concrete lining are investigated. Numerical analyses are done in various conditions. And the rock loads estimated from radial stress and plastic zone are compared respectively.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.153-160
• /
• 1999

It has been recognized that the assessment of concrete lining is very uncertain and subjective depending on the engineers who are in charge. T-FLAS which was based on fuzzy theory was developed in this study for the quantitative and objective assessment of the concrete lining in tunnels. Based on the application of T-FLAS on the evaluated field data, it was shown that the assessment system using fuzzy theory(T-FLAS) can be the effective and objective method for the assessment of concrete lining.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.541-544
• /
• 2008

Generally numerical analysis of tunnel lining, under dynamic loading condition, performed not considering pore pressure. But if tunnel excavated under the surface of water, such as bottom of the sea, the river bed, tunnel lining can take pore water pressure. It may be different from evaluated numerical analysis not considering pore pressure. Therefore tunnel design should consider effect of water pressure acting on tunnel lining.

• 한국터널지하공간학회 논문집
• /
• 제8권4호
• /
• pp.365-375
• /
• 2006

일반적으로 터널2차라이닝의 구조해석에는 골조해석모델이 적용되고 있다. 본 모델은 경험적 방법에 의한 지반 이완하중을 고려하고 있으나 주관적이고 과대평가되는 경향이 있다. 2차라이닝에 작용하는 지반하중은 숏크리트 및 록볼트와 같은1차지보재의 지지력 상실에 기인한다. 그러므로 2차라이닝에 작용하는 지반하중 산정에는 1차지보재와 지반의 평형상태가 고려되어야 한다. 지반-라이닝 상호작용(Ground-Lining Interaction, GLI)모델은1차지보재의 지지력 상실에 의해 야기된 지반의 변형을2차라이닝이 지지하는 개념을 토대로 수립되었다. 따라서 GLI모델은 복잡한 지반조건과 1차 지보재의 설치조건을 합리적으로 반영한 지반하중을 고려할 수 있다. 2차라이닝에 작용하는 하중은 지반하중 외에 지하수압, 지진하중 등이 있다. 극한강도 설계법을 이용한 라이닝 구조보강을 위해서는 계수하중 및 다양한 하중조합이 고려되어야 한다. GLI모델은 계수하중을 고려하기 곤란하기 때문에 개별 하중에 대해 산정된2차라이닝 단면력에 하중계수를 곱하는 중첩의 원리를 적용하였다. 끝으로, 본 연구에서 제시된 GLI모델을 이용한 2차라이닝 설계방법을 저심도 지하철 터널에 적용하였다.

• 한국터널지하공간학회 논문집
• /
• 제26권3호
• /
• pp.255-280
• /
• 2024

쉴드TBM 터널에서 단면 부족이나 큰 변형이 세그먼트 라이닝의 안정성에 우려될 경우 터널 외부에 지반 그라우팅으로 보강하거나 터널 내부에 강판 보강, 링 빔 보강, Inner double layer lining으로 보강하는 경우가 있다. 또한, 기존의 쉴드 TBM 터널의 해석은 세그먼트라이닝의 분절 특성을 고려하지 않는 연속체의 강성일체법으로 해석되어왔다. 본 연구는 내부 강재 라이닝으로 보강한 double layer 보강 단면에 대해 보강 메커니즘을 연구하였다. 본 연구는 세그먼트 라이닝에 대한 모델링을 개선하여 세그먼트 라이닝의 분절 특성을 고려한 분절체 모델링(BJM)을 적용하였고 이를 통해 세그먼트 라이닝의 변형 특성을 반영한 double layer 보강 단면을 해석하였다. 연구 결과 기존 콘크리트 세그먼트 라이닝은 하중을 일정부분 분담하는 역할이 아닌 터널 주변 지반을 보강한 것과 같은 역할을 하였다. 일반적으로, 세그먼트 라이닝의 분절을 고려한 BJM 모델과 분절을 고려하지 않는 강성일체법 모두 하중을 받은 라이닝의 변형 형상과 응력 분포가 유사하게 나타났다. 그러나 하중의 강도가 임계치를 넘는 경우 변형의 양상에 차이가 있으며 변형 특성을 보다 면밀히 검토할 수 있는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.621-628
• /
• 2005

The concrete lining in tunnel performs structural and nonstructural functions. The concrete lining works as a structural member for released load and residual water pressure in NATM tunnel system. Also concrete lining used for finishing the tunnel surface. The initial crack of concrete lining is reported because of difficulties in construction process, which concrete is injected into 30$\sim$40cm narrow gap between lining form and tunnel surface through 500${\times}$600mm small injection holes in the form. In this paper, we research a reason of initial crack occurrence by the case study of 4 lane wide span tunnel, and propose an improved method for crack minimization in construction process. We verify that the proposed method can give qualified concrete lining by carrying out the concrete injection model test and the numerical analysis of concrete flow.

• International Journal of Concrete Structures and Materials
• /
• 제2권2호
• /
• pp.145-152
• /
• 2008

So far, there has been no study of the concrete to strengthen in the lining of the tunnels, except for the study of the stability of subgrade and the tunnel construction technologies. In the existing concrete work for tunnel lining, lots of problems happen due to the partial compaction and the material segregation after casting concrete. Accordingly, the aim of this study is to improve economic efficiency and secure durability through the improvement of the construction performance and quality of the concrete for the tunnel lining among the civil structures. Therefore, the compactability and strength properties of the High Flowing Self-Compacting Lining Concrete (HSLC) are evaluated to develop the mixing proportion for design construction technology of HSLC that can overcome the inner cavity due to the reduced flowability and unfilled packing, which has been reported as the problem in the existing lining concrete. The result of the evaluation shows that the ternary mix meets the regulations better than the binary mix. Consequently, it has been judged applicable to the cement for tunnel lining.

• 한국터널공학회:학술대회논문집
• /
• 한국터널공학회 2005년도 학술발표회 논문집
• /
• pp.270-281
• /
• 2005

An especial attention for old tunnel safety is required on increasing of The various tunnel recently. Specially, the lining investigation method of the old tunnel will be able to presume condition of concrete lining indirectly. Because it is many restriction thought of environment and ground condition investigation method of tunnel lining rear. This study carried out section & convergence measurement of part which was deformed in tunnel lining. It had been observed for the change of tunnel behavior with a continuous measurement. It has been analyzed for a cause of tunnel deformation and inspected for the effect after a repair-reinforcement to tunnel compared with the effect before those by structure analysis. By establishing automatic measurement system after repair-reinforcement to tunnel, it would be accomplished to convergence measurement continually. As a result, it was observed that deflection and deformation of tunnel was convergent. but it should be followed to a continuous maintenance because of unstable ground condition, cause of inner tunnel, environment. The railroad tunnel which was executed a reinforcement of the tunnel lining must investigate the close condition of reinforcement lining and concrete lining.

• Computers and Concrete
• /
• 제21권4호
• /
• pp.399-406
• /
• 2018

The present study focuses on the performance of basalt fiber reinforced concrete (BFRC) lining in tunnel situated in sandstone rock when subjected to internal blast loading. The blast analysis of the lined tunnel is carried out using the three-dimensional (3-D) nonlinear finite element (FE) method. The stress-strain response of the sandstone rock is simulated using a crushable plasticity model which can simulate the brittle behavior of rock and that of BFRC lining is analyzed using a damaged plasticity model for concrete capturing damage response. The strain rate dependent material properties of BFRC are collected from the literature and that of rock are taken from the authors' previous work using split Hopkinson pressure bar (SHPB). The constitutive model performance is validated through the FE simulation of SHPB test and the comparison of simulation results with the experimental data. Further, blast loading in the tunnel is simulated for 10 kg and 50 kg Trinitrotoluene (TNT) charge weights using the equivalent pressure-time curves obtained through hydrocode simulations. The analysis results are studied for the stress and displacement response of rock and tunnel lining. Blast performance of BFRC lining is compared with that of plain concrete (PC) and steel fiber reinforced concrete (SFRC) lining materials. It is observed that the BFRC lining exhibits almost 65% lesser displacement as compared to PC and 30% lesser displacement as compared to SFRC tunnel linings.

• 한국의류학회지
• /
• 제8권1호
• /
• pp.1-11
• /
• 1984

An attempt was made to determine individual thermal resistances of 2-lining fabrics ad 4-outer fabrics for Korean-styled clothes, and 4-lining fabrics ad 5-outer fabrics for Western-styled clothes at $19^{\circ}C$ and $24^{\circ}C$. The thermal insulation effects for different lining fabrics in Korean and Western-styled clothes were deduced in determining heart rate, rectal temperature, mean skin temperature and microclimates of subjects. The subjects were dressed experimental clothing which were made of lining and outer fabrics in question, and seated in an environmental chamber during the experiment. 1. Thermal resistances of lining fabrics : For Korean-styled clothes. nylon sheer is larger than unzosa. For Western-styled clothes, rayon, acetate, nylon(taffeta) and kalkali in that order. 2. Thermal resistances of lining fabrics combined : with outer fabrics: For Korean-styled clothes. the measured value is larger than the one of simple aggregate value. But in the case of Western-styled clothes, the measured value is smaller than simple aggregate value. 3. The effects of lining on the thermal insulation of the whole clothing: In case when subjects wore unlimited number of underwear, no matter what lining fabrics were used in Korean and Western-styled clothes less thermal insulation effects were indicated. For the case, however, if subjects wore only limited underwear, there are significant differences of thermal insulation between experimental clothings.