• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.49-52
• /
• 2003

Two types of ozone monitors using UV absorption method were tried in consideration of cost of the monitor and precision in measuring. The high concentration ozone monitor for high concentration real time ozone monitoring from ozone generator was composed of a low pressure mercury lamp as UV source, a photo multiplier tube as UV detector and signal processing unit for the most part. This structure could be very useful for low price high concentration ozone monitor due to simple system structure and fairly good monitoring characteristics. The developed system showed good linear output characteristics to ozone in the measuring concentration range of 0.05 and 2 wt.%. For accuracy ambient ozone monitoring in ambient in ppm level, the system composed of a high power pulsed xenon lamp as UV source, an optical spectrometer with a high sensitivity linear CCD array as UV detector and signal processing unit in brief speaking was proposed our study for the first time in the world. The developed system showed good linearity and sensitivity in relative low measuring range between 10ppm and 10,000ppm, and showed some feasibility of high resolution ozone monitor using CCD array as photodetector.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.150-153
• /
• 1997

In this paper, a control and data analysis S/W of a dedicated measuring machine for cams is developed. A rotary encoder is employed to measure the angular displacement of the motor, and a linear scale does the linear displacement of the prove. The design and measuring data are interpolated by cubic spline curves respectively to compute the error which is defined by the maximum distance between two curves. Further, optimization module to find the exact error is also developed to remove the error occurred due initial measuring position. The developed system takes only 6 minutes to measure the cam and to analyze the measuring data while the CMM takes about 1 hours even with a skilled operator.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2146-2148
• /
• 1997

We had developed a prototype Linear Pulse Motor(LPM) for the linear motion actuator. In this paper, it is mentioned a new dynamic equations which is considered the nonlinearity of the thrust force of LPM. And a measuring method of ripples in the thrust forces is proposed and the ripples were measured in the laboratory. In the experimental results, it is shown the validity of the proposed measuring method for catching of the ripple values and waveforms in the thrust force.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.160-166
• /
• 2002

In this paper, data acquisition and analysis of a measuring machine for marine engine's cams is discussed. A rotary encoder and linear scale of the machine to measure angular and linear displacement respectively are interfaced to the PC via encoder board with 2 channels. The design and measuring data are interpolated by cubic spline curves to compute the precision error which is defined by the maximum and minimum distances between two curves. The minimum zone fit of ISO is employed to evaluate the geometric deviation. The developed system takes only 5 minutes to measure and analyze while the CMM takes over 1 hours even with a skilled operator.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.4
• /
• pp.21-27
• /
• 2004

In this paper, data acquisition and analysis of a measuring machine for marine engine's cams are discussed. A rotary encoder and linear scale of the machine to measure angular and linear displacement, respectively, are interfaced to the PC via an encoder board with 2 channels. The design and measuring data are interpolated by cubic spline curves to compute the precision error which is defined by the maximum and minimum distances between two curves. The minimum zone fit of ISO is employed to evaluate the geometric deviation. The developed system takes only 5 minutes to measure and analyze the precision error while the CMM takes over I hours even with a skilled operator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.305-311
• /
• 1993

In recent years, it has been variously developed for testing the accuracy of circular motion of NC machine tools, for example Telescoping Ball Bar Method by Bryan,Circular Test Method by Knapp and r $_{- \theta}$ Mathod by Tsutsumi etc., but it is not yet settled in the code of measuring methods of motion errors of NC machine tools, because of errors of measuring units and sensors, and also especially the difficulties of centering of measuring units. In this paper, in use of magnetic type linear scale with resolution of 0.5 .mu. m and tick pulses come out from computer, it has become possible for detecting of linear displacement of radial errors and measuring of revolution angle of circular motion of NC machine tools.

• Journal of KSNVE
• /
• v.7 no.2
• /
• pp.223-229
• /
• 1997

Presented is a method to estimate system parameters of a system with polynomial non-linerities from the measured higher order frequency response functions. Higher order FRFs can be measured on some restricted regions by sinusoidally exciting a non-linear system with various input amplitudes and measuring the response component at the excitation frequency. These higher order FRFs can be expressed in terms of system parameter, and the system parameters can be estimated from the measured FRFs. Since the expressions for higher order FRFs are complicated, system parameters can be estimated from them using an optimization technique. The present method has been applied to a simulated single degree of freedom system with non-linear stiffness and damping, and has estimated accurate system parameters.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.291-292
• /
• 2006

Currently A demand of high precision workpiece is increasing in industry. At present, roundness measuring machine using Air bearing, coordinate measuring machine that are used from measurement station. but these machines will not be able to apply to In-line process. because of like these machine's price are very expensive and measurement time is long. also, the complexity of conventional roundness measurement method based on fourier transform, it makes difficult to development analysis program. This work present new architecture of a Out-diameter measuring system fur analysis of roundness of product. In this system, the influence of table motion errors is minimize by using two LVDT sensor and knife edge contact tip. We are produce a test machine and make an experimenter on Out-diameter of test bearing. The measurement result compared with roundness measuring machine.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.12
• /
• pp.943-947
• /
• 2014

Recently, a new method for reconstructing a forced nonlinear dynamic system has been proposed; specifically, the simultaneous reconstruction of its excitation as well as restoring characteristics of the system. The reconstruction was just theoretically shown to be possible by measuring the system's responses, based on newly introduced notions, a J-function and a zero-crossing time. However, numerically in the current paper, we are to reconstruct a linear system, i.e., we focus on numerical experiments to reconstruct both the excitation and the linear restoring characteristic of a linear forced oscillating system by using response data, based on the J-function and the zero-crossing time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.621-628
• /
• 2000

A kinematic ball bar measuring system can analyze the various errors of a machine tool easil rapidly with only one measurement, But it cannot be used to measure the errors of the equipment the semiconductor manufacturing (e.g. chip mounter, PCB router etc.) not to use a cir interpolation. This paper presents the method to apply a kinematic ball bar measuring system tc machines which use merely a linear interpolation Also, the work of measuring and calibratir various errors of a chip mounter with a kinematic bal1 bar measurement system is accomplished