• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1750-1754
• /
• 2013

A variable bit rate speech coder is presented. The coder is based on the observation that a speech signal can be viewed as a combination of piecewise linear signals in a short time period. The encoder detects the sample points where the slope of the signal changes, which are called the inflection points in this paper. The coder transmits the location and value for the detected inflection sample, but only the location information for the noninflection samples. In the decoder, the noninflection samples are estimated with interpolation of the received information. Several factors affecting the performance of the coder have been tested through simulation. Simulation results show that the linear interpolation produces 1 ~ 5 dB improvement over the cubic spline interpolation. And the -law companding does not provide any benefit when it is applied before the inflection detection. With low threshold values in the inflection point detection, the coder shows better MOS and more than 16 dB improvement in SNR compared to the continuously variable slope delta modulation (CVSDM).

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.405-405
• /
• 2000

We designed the artificial olfactory sensing system (Electronic Nose) using MOS type sensor array fur recognizing and analyzing odour. The response of individual sensors of sensor array, each processing a slightly different response towards the sample volatiles, can provide enough information to discriminate between sample odours. In this paper, we applied clustering algorithm for dimension reduction, such as linear projection mapping (PCA method), nonlinear mapping (Sammon mapping method) and the combination of PCA and Sammon mapping having a better discriminating ability. The odours used are VOC (Volatile chemical compound) and Toxic gases.

• Journal of KSNVE
• /
• v.4 no.2
• /
• pp.137-146
• /
• 1994

An analytical method for linear free vibration of fully liquid-filled circular cylindrical shell with various boundary conditions is developed by the Fourier series expansion based on the Stokes' transformation. A set of modal displacement functions and their derivatives of a circular cylindrical shell is substituted into the Sanders' shell equations in order to explicitily represent the Fourier coefficients as functions of the end point displacements, forces, and moments. For the vibration relevant to the liquid motion, the velocity potential of liquid is assumed as a sum of linear combination of suitable harmonic functions in the axial directions. The unknown parameter of the velocity potential is selected to satisfy the boundary condition along the wetted shell surface. An explicit expression of the natural frequency equation can be obtained for any kind of classical boundary conditions. The natural frequencies of the liquid-filled cylindrical shells with the clamped-free, the clamped-clamped, and the simply supported-simply supported boundary conditions examined in the previous works, are obtained by the analytical method. The results are compared with the previous works, and excellent agreement is found for the natural frequencies of the shells.

• Journal of Communications and Networks
• /
• v.16 no.4
• /
• pp.436-446
• /
• 2014

The high intensity of research and modeling in fields of mathematics, physics, biology and chemistry requires new computing resources. For the big computational complexity of such tasks computing time is large and costly. The most efficient way to increase efficiency is to adopt parallel principles. Purpose of this paper is to present the issue of parallel computing with emphasis on the analysis of parallel systems, the impact of communication delays on their efficiency and on overall execution time. Paper focuses is on finite algorithms for solving systems of linear equations, namely the matrix manipulation (Gauss elimination method, GEM). Algorithms are designed for architectures with shared memory (open multiprocessing, openMP), distributed-memory (message passing interface, MPI) and for their combination (MPI + openMP). The properties of the algorithms were analytically determined and they were experimentally verified. The conclusions are drawn for theory and practice.

• Earthquakes and Structures
• /
• v.8 no.5
• /
• pp.1255-1276
• /
• 2015

The importance of considering soil-structure interaction effect in the analysis and design of RC frame buildings is increasingly recognized but still not penetrated to the grass root level owing to various complexities involved. It is well established fact that the soil-structure interaction effect considerably influence the design of multi-storey buildings subjected to lateral seismic loads. The shear walls are often provided in such buildings to increase the lateral stability to resist seismic lateral loads. In the present work, the linear soil-structure analysis of a G+5 storey RC shear wall building frame resting on isolated column footings and supported by deformable soil is presented. The finite element modelling and analysis is carried out using ANSYS software under normal loads as well as under seismic loads. Various load combinations are considered as per IS-1893 (Part-1):2002. The interaction analysis is carried out with and without shear wall to investigate the effect of inclusion of shear wall on the total and differential settlements in the footings due to deformations in the soil mass. The frame and soil mass both are considered to behave in linear elastic manner. It is observed that the soil-structure interaction effect causes significant total and differential settlements in the footings. Maximum total settlement in footings occurs under vertical loads and inner footings settle more than outer footings creating a saucer shaped settlement profile of the footings. Each combination of seismic loads causes maximum differential settlement in one or more footings. Presence of shear wall decreases pulling/pushing effect of seismic forces on footings resulting in more stability to the structures.

• Structural Engineering and Mechanics
• /
• v.39 no.5
• /
• pp.703-716
• /
• 2011

The accurate dynamic analysis of structures is usually performed by a fine finite element discretization with very large number of degrees of freedom. Apart from modal analysis, one can reduce the number of final equations by assuming the deformed shape of the structure as a linear combination of independent Ritz vectors. The efficiency of this method relies heavily on the vectors selected. In this paper, a new set of Ritz vectors is proposed. It is primarily proved that these vectors are linearly independent. Subsequently, various two and three-dimensional examples are analyzed based on the proposed method. In each case, the results are compared with the ones obtained based on usual Ritz and modal analysis methods. It is finally concluded that the proposed method is very effective and efficient method for dynamic analysis of structures in frequency domain.

• Journal of Environmental Science International
• /
• v.20 no.12
• /
• pp.1541-1551
• /
• 2011

This study applied the Bayesian method for the quantification of the parameter uncertainty of spatial linear mixed model in the estimation of the spatial distribution of probability rainfall. In the application of Bayesian method, the prior sensitivity analysis was implemented by using the priors normally selected in the existing studies which applied the Bayesian method for the puppose of assessing the influence which the selection of the priors of model parameters had on posteriors. As a result, the posteriors of parameters were differently estimated which priors were selected, and then in the case of the prior combination, F-S-E, the sizes of uncertainty intervals were minimum and the modes, means and medians of the posteriors were similar to the estimates using the existing classical methods. From the comparitive analysis between Bayesian and plug-in spatial predictions, we could find that the uncertainty of plug-in prediction could be slightly underestimated than that of Bayesian prediction.

• Journal of Information Processing Systems
• /
• v.3 no.1
• /
• pp.33-37
• /
• 2007

Semantic clustering is important to various fields in the modem information society. In this work we applied the Independent Component Analysis method to the extraction of the features of latent concepts. We used verb and object noun information and formulated a concept as a linear combination of verbs. The proposed method is shown to be suitable for our framework and it performs better than a hierarchical clustering in latent semantic space for finding out invisible information from the data.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.781-786
• /
• 2008

In this paper, we propose a novel approach predicting the fluctuation of stock index by finding a relation in various stock indexes that are represented by linear combinations. The important points are to select stock indexes related to predicting indexes and to find the proper relations in them. Since it is unattainable to use entire stock indexes relation, we used only data that are closely associated with each other. We used Genetic Algorithm(GA) to find the most suitable stock-index relation. We simulated the investment in years from 2005 to 2007 with each real index. Finally we verified that the investment money increased 230 percents by the proposed method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.37-44
• /
• 2018

In laser material processing for high thermal conductivity, the thermal effect of laser beam shape was examined through computer simulations. In this paper, a circular beam with a focal radius of $500{\mu}m$, an elliptical beam with a major axis of 4 mm and a minor axis of 1 mm, and a rotating beam with a focal radius of $500{\mu}m$ and an angular velocity of 5 rad/sec were compared. Simulation results showed that there was no clear difference in the maximum temperature between the circular focus and the elliptical shape, but the heating and cooling rates were different. The simulation result for a laser beam rotating in a circular pattern with a radius of 5 mm showed an asymmetric temperature rise due to the combination of linear and rotational motion. At points where the rotational and linear speeds combined, the temperature gradually rose and reached the maximum temperature; whereas at points where the rotational and linear speeds were attenuated, the temperature tended to gradually decrease after reaching the maximum temperature. Based on the results of this study, the authors expect to be able to optimize laser material processing by designing patterns of laser beams.