• 에너지공학
• /
• 제19권3호
• /
• pp.143-150
• /
• 2010

선형열원 해석은 열원 주위가 완전히 균일한 매질로 이루어져 있다는 가정 하에 성립되는 해석이나 실제 보어홀 시스템의 경우 그라우팅 영역은 주위토양과 매우 다른 열물성치를 가진 물질로 이루어져 있다. 본 연구에서는 이러한 그라우팅 영역이 선형열원 해석에 어떠한 영향을 미치는가를 연구하였다. 연구방법으로는 먼저 수치모델을 개발하고 이 수치모델에 의하여 시간에 따른 보어홀 유체온도를 생성한 후 이 유체온도를 선형열원법에 이용하여 지중열전도도와 보어홀 전열저항을 구하며 이렇게 구한 해를 수치모델의 입력조건과 비교함으로서 그 차이점을 규명한다. 이러한 해석결과 선형열원법의 해인 지중열전도도와 보어홀 전열 저항은 수치모델 입력조건에 비해 대략, 86%와 91%의 수준으로 나타났다. 선형열원 해로부터 수치모델의 입력조건을 역산해 나가는 Chart법이 본 연구에서 개발되었으며 시험용 보어홀의 열응답시험 결과와 비교해 본 결과 이 Chart법은 신뢰성이 있는 것으로 나타났다. 그라우트 영역의 열물성치를 변화시켜가며 선형열원해의 특성이 어떻게 변하는지도 검토하였다.

• 한국강구조학회 논문집
• /
• 제8권3호통권28호
• /
• pp.97-105
• /
• 1996

A Stochastic line source model is developed to simulate the seismic wave field generated during the rupture propagation process along a fault plane of which length is much larger than its width. The fault plane is assumed to consist of randomly distributed slip zones and barriers and each slip zone is modeled as a point source. By combining the newly developed source model with wave propagation analysis method in a layered 3-D visco-elastic half space, synthetic seismograms are obtained. The calculated accelerograms due to vertical dip slip and strike slip line sources are presented.

• 조명전기설비학회논문지
• /
• 제27권2호
• /
• pp.45-53
• /
• 2013

In this paper, we analyze the typical phase voltage and line current waveform characteristics of the distribution system with 3 phase small synchronous generation source in case with load and non-load group, in order to investigate the power quality for end load connected of generation source. As demonstrated by our experimental results, the distortion and power quality of phase voltage and line current waveform were relatively good for low voltage 3 phase model grids connected of 3 phase small synchronous generation source in case with non-load group. However, distortion and power quality of voltage and current waveform was poor for low voltage 3 phase model grids connected to 3 phase small synchronous generation source in the load group with some phase voltage and frequency difference. From the above results, we conclude that the phase voltage and frequency of 3 phase generation source must be identical to that of distribution system source to maximize the power quality. Also, special attention is required in case of having load group or non-load group to 3 phase generation source.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1112-1115
• /
• 2004

Recently, KTX start service 2004 and speed up the Chung-ang line and Ho-nam line using tilting train. When the train speed up at curve the vibration environment are changed. It is the reason of the wave propagation problem in the curved source. In this research, using SSI Program SASSI, Predict the vibration propagation around the curved source of vibration. The curved source of vibration propagation is different from straight source of vibration propagation. In this study, made a curved vibration source model and compared with straight model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1760-1762
• /
• 2002

In this work we develop an equivalent circuit model of TCP(transformer coupled plasma) source and investigate matching characteristic. The developed circuit model includes transmission line, standard-type impedance matching network and displacement current in the plasma source. The impedance of TCP is calculated by previously developed program for various source parameters and dependance of components of matching impedance on the value of source impedance is investigated.

• 소음진동
• /
• 제6권6호
• /
• pp.835-842
• /
• 1996

To identify the locations and strengths of acoustic sources, one may use a microphone line array. Apparent advantage of the source identification method utilizing a line array is that it requires less measurement points than intensity method and holography. This method is based on the information of magnitude and phase difference between pressure signals at each microphone. Since those differences are dependent on the source model, we have to assume them such as plane, monopole, etc. In this paper the conventional source identification methods such as beamforming method and MUSIC method are briefly reviewed by modeling a source as plane and spherical wave, then a modified method is introduced. This can be applied to sound field which may by either coherent or incoherent. Typical simulations and experiment are performed to confirm this identification method.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.550-554
• /
• 2007

A one-dimensional heat transfer model coupled with parameter estimation is developed in this study to predict the effective thermal conductivities of soil formation and borehole resistances from in situ field test data. In this application a new method of using initial ignoring time(IIT) obtained from error estimation is tried and turned out to be successful in determining soil thermal conductivities. The validity of this model is accomplished through comparison of the predicted temperature profiles of the model with the data from laboratory scale experimental setting. Eleven test boreholes were constructed in Ochang, Chungcheong Buk Do, and thermal response test was carried out with each borehole. The results of the in situ tests were analyzed with our 1-D numerical model and compared with the results of line source method. The comparison shows that the thermal properties from line source method is a little lower (${\sim}95%$)than those from numerical method. The reason of such result seems to be the lower thermal conductivity of grout material, which is not counted in line source method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.446-448
• /
• 1995

This paper dscribes a detail simulation model with EMTP (Electro-Magnetic Transients Program) which is very effective to analyze the interaction between the ac transmission line and STATCON (static condenser). The SATCON was represented by two voltage-source converters connected in parallel and sharing an energy storage dc capacitor bank. The voltage source converters was modeled with ideal gate turn-off switches. The power system was represented by a detail generator model and a distributed tramnsmission line model for detail performance analyses. Analysis results show that the conceived simulation model is very effective to analyze the interaction between the ac transmission line and STATCON, and to evaluate the performance of STATCON.

• 에너지공학
• /
• 제17권3호
• /
• pp.167-174
• /
• 2008

지중유효열전도율 측정에서는 선형열원 모델이 열응답 시험의 자료 해석에 주로 이용되고 있는 실정이다. 이 선형열원 모델의 응용에서는 해의 신뢰도를 높이기 위하여 일정시간의 초기자료를 폐기하여야 하며 이 일정시간을 본 연구에서는 초기제외시간으로 명명한다. 그런데 이 초기제외시간의 산정에 관하여 뚜렷한 기준이 마련되어 있지 않아 선형열원 모델을 이용한 자료해석에서는 초기제외시간 선정이 다소 주관적이 되는 경향이 있으며 따라서 이 모델의 응용에는 충분한 경험이 필요하다. 무차원 시간 $\tau=5$가 초기제외시간 선정에 한 기준으로 제시되기도 하였으나 이 역시 완전한 선형열원 모델에서 도출되는 매우 이론적인 결과이며 실제 시스템은 이 이론적인 선형열원과 다른 점이 많다. 본 연구에서는 초기제외시간을 선정하는 새로운 방법을 제시한다. 이 방법에서는 먼저 오차해석을 수행하고 그 결과를 토대로 초기제외시간을 결정하게 된다. 본 연구에서는 이 방법을 2개의 현지 시험결과에 적용하여 보았으며 위에 언급한 $\tau=5$에 의한 방법보다 훨씬 더 신뢰성 높은 결과를 도출할 수 있었다(Table 2 참조).

• 한국대기환경학회지
• /
• 제24권1호
• /
• pp.122-127
• /
• 2008

The purpose of this study is to calculate atmospheric environmental capacity for $PM_{10}$, $NO_2$ and $SO_2$ using a rollback model in Chungju. From the results of this study, the source contributions for $PM_{10}$ and $NO_2$ was the following order: line source > area source > point source. However, the source contributions for $SO_2$ was the following: point source > area source > line source. While the atmospheric environmental capacity of $NO_2$ and $SO_2$ was enough to meet the regional air quality target, $PM_{10}$ emission needs to be reduced by 5%.