• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.621-633
• /
• 2015

This paper proposes the analysis and design of a DC-side symmetrical zero-current-switching (ZCS) Class-D current-source driven resonant rectifier to improve the low power-factor and high line current harmonic distortion of lighting applications. An analysis of the junction capacitance effect of Class-D ZCS rectifier diodes, which has a significant impact on line current harmonic distortion, is discussed in this paper. The design procedure is based on the principle of the symmetrical Class-D ZCS rectifier, which ensures more accurate results and provides a more systematic and feasible analysis methodology. Improvement in the power quality is achieved by using the output characteristics of the DC-side Class-D ZCS rectifier, which is inserted between the front-end bridge-rectifier and the bulk-filter capacitor. By using this symmetrical topology, the conduction angle of the bridge-rectifier diode current is increased and the low line harmonic distortion and power-factor near unity were naturally achieved. The peak and ripple values of the line current are also reduced, which allows for a reduced filter-inductor volume of the electromagnetic interference (EMI) filter. In addition, low-cost standard-recovery diodes can be employed as a bridge-rectifier. The validity of the theoretical analysis is confirmed by simulation and experimental results.

• 대한원격탐사학회지
• /
• 제19권6호
• /
• pp.431-445
• /
• 2003

본 연구에서는 사진측량 관점에서 4S-Van 영상을 이용한 3차원 위치결정의 정밀도를 실험적으로 검증하였다. 실외에 3차원 검정타겟을 설치하고 45-Van에 탑재된 2대의 CCD카메라로부터 검정타겟 영상을 개별적으로 취득하여 자체검정기법으로 각각의 CCD카메라에 대한 내부표정요소를 개별적으로 정확하게 결정하였다. 이와 같이 얻어진 내부표정요소와 검정타겟의 지상좌표 및 검정타겟을 동시에 촬영한 좌ㆍ우측 카메라의 영상좌표를 이용하여 광속조정법으로 2대 CCD카메라의 외부표정요소를 동시에 결정하였다. 또한, 렌즈왜곡이 고려된 에피폴라선을 이용하기 위하여 역렌즈왜곡계수를 최소제곱법을 이용하여 결정하였다. 역렌즈왜곡계수를 이용하여 약 0.5 pixel 이내로 렌즈왜곡이 포함된 영상좌표로 변환이 가능하였다. 렌즈왜곡이 고려된 에피폴라선을 이용한 반자동 영상매칭을 적용하여 3차원 위치결정의 정밀도를 검증하였다. 실험적으로 촬영거리 20m이내에서는 대략2cm 정도의 정밀도를 얻을 수 있었다.

• Imaging Science in Dentistry
• /
• 제48권4호
• /
• pp.255-259
• /
• 2018

Purpose: This study proposes a new ball-type phantom for evaluation of the image layer of panoramic radiography. Materials and Methods: The arch shape of an acrylic resin phantom was derived from average data on the lower dental arch in Korean adult males. Metal balls with a 2-mm diameter were placed along the center line of the phantom at a 4-mm mesiodistal interval. Additional metal balls were placed along the 22 arch-shaped lines that ran parallel to the center line at 2-mm buccolingual intervals. The height of each ball in the horizontal plane was spaced by 2.5 mm, and consequently, the balls appeared oblique when viewed from the side. The resulting phantom was named the Panorama phantom. The distortion rate of the balls in the acquired image was measured by automatically calculating the difference between the vertical and horizontal length using $MATLAB^{(R)}$. Image layer boundaries were obtained by applying various distortion rate thresholds. Results: Most areas containing metal balls (91.5%) were included in the image layer with a 50% distortion rate threshold. When a 5% distortion rate threshold was applied, the image layer was formed with a small buccolingual width along the arch-shaped center line. However, it was medially located in the temporomandibular joint region. Conclusion: The Panorama phantom could be used to evaluate the image layer of panoramic radiography, including all mesiodistal areas with large buccolingual width.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권8호
• /
• pp.405-412
• /
• 2003

This paper presents a three-phase Line-Interactive uninterruptible power supply (UPS) system with series-parallel active power-line conditioning capabilities, using synchronous reference frame (SRF) based controller, which allows an effective power factor correction, source harmonic voltage compensation, load harmonic current suppression, and output voltage regulation. The three-phase UPS system consists of two active power compensator topologies. One is a series active compensator, which works as a voltage source in phase with the source voltage to have the sinusoidal source current and high power factor under the deviation and distortion of the source voltage. The other is a parallel active compensator which works as a conventional sinusoidal voltage source in phase with the source voltage, providing to the load a regulated and sinusoidal voltage with low THD (total harmonic distortion). The control algorithm using SRF method and the active power flow through the Line-interactive UPS systems are described and studied. The simulation and experimental results are depicted in this paper to show the effect of the proposed algorithm.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.661-667
• /
• 2002

Welding-induced buckling distortion is one of the most problematic concerns in both design and fabrication of welded thin-plate structures. This paper deals with experimental and numerical results of the welding-induced longitudinal and/or buckling distortion occurring in welding of 6mm-thick AH36 high strength steel plates. Effects of the heat input and the plate size on the distortion were experimentally evaluated for square plates. Bead-on-plate welding was performed with the submerged arc welding process along the middle line of plate specimens. Experimental results showed that the longitudinal distortion made a single curvature in the plate, and the distortion magnitude along the weld centerline was proportional to the heat input and the plate size. The experimental results were used to examine the validity of the numerical simulation procedure for welding-induced distortion where the longitudinal distortion mode and magnitude were numerically quantified. Three-dimensional, large deformation, welding simulations were performed for selected weld models. Numerical results of the distortion mode and magnitude were in a good agreement with experimental ones. Depending on the presence of halting the distortion growth during the cooling cycle of welding, the condition discriminating buckling distortion from longitudinal distortion was established. Eigenvalue analyses were performed to check the buckling instability of tested plates with different sizes subjected to different heat inputs. The perturbation load pattern for the analysis was extracted from longitudinal inherent strain distributions. Critical buckling curve from the eigenvalue analyses revealed that the buckling instability is manifested when plate size or heat input increases.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.162-163
• /
• 2000

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1617-1620
• /
• 1997

This paper describes the camera caliberation based-neural network with a camera modeling that accounts for major sources of camera distortion, namely, radial, decentering, and thin prism distortion. Radial distoriton causes an inward or outward displacement of a given image point from its ideal location. Actual optical systems are subject to various degrees of decentering, that is the optical centers of lens elements are not strictly collinear. Thin prism distortion arises from imperfection in lens design and manufacturing as well as camera assembly. It is our purpose to develop the vision system for the pattern recognition and the automatic test of parts and to apply the line of manufacturing. The performance of proposed camera aclibration is illustrated by simulation and experiment.

• 한국생산제조학회지
• /
• 제7권4호
• /
• pp.64-72
• /
• 1998

This paper a new approach to the design of machine vision technique with a camera modeling that accounts for major sources of geometric distortion, namely, radial, decentering, and thin prism distortion. Radial distortion causes an inward or outward displacement of a given image point from its ideal location. Actual optical systems are subject to various degrees of decentering , that is , the optical centers of lens design and manufacturing as well as camera assembly. It is our propose to develop the vision system for the pattern recognition and the automatic test of parts and to apply the line of manufacturing. The performance of proposed vision system is illustrated by simulation and experiment.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(5)
• /
• pp.218-221
• /
• 2000

The electronystagmography(ENG) means to measure and record CRP(Corneal-Retinal Potential) whenever the eyeball is moved by using a skin electrode stuck to the hi-temporal and the difference of CRP. Both the horizontal and vertical movement are known according to the position of the stuck skin electrode. In this paper, the variable time-constances to record the eyeball signal of the conventional EOG(Electro-Oculograph) Amplifier is chosen. The shorter the time-constance is, the worse the distortion of a signal is. But the unbalanced impedance of the electrode stuck on the hi-temporal is reduced. Also, the longer the time-constance is, the less the distortion of it signal is. But it is sensitive to the change of base line according to the unbalanced impedance. In order to solve these problems, an DC-Amplifier, the distortion of the eyeball signal is globally used. By solving unbalanced impedance problem of EOG amplifier, the distortion ratio of EOG amplifier is improved.

• 대한조선학회논문집
• /
• 제45권4호
• /
• pp.417-425
• /
• 2008

In the line heating process, only angular distortion whose direction is perpendicular to that of a heating path is expected. However, it is observed that a deformation is induced in the direction of the heating line. Because of this, during forming a saddle type plate we experience unfavorable deformations in the unintended direction. In this paper we discuss the unwanted distortion in the manufacturing process by analyzing intermediate plates of saddle type during fabrication. For this analysis we consider the longitudinal and transversal directions separately and use the bending strain for the analysis.