• 한국통신학회논문지
• /
• 제21권7호
• /
• pp.1842-1849
• /
• 1996

This paper presents a full-wave, moment method analysis of a Moreno directional coupler with tow crossed-slots between two crossed rectangular waveguides. the overall structure is divided into several rectangular waveguides and cavities by the use of the equivalence principle to the complex slot regions. this enables a simple and efficient analysis involving the well-known retangular waveguide/cavity Green's functions. For a numerically efficient simulation, the roof-top basis expansion and line testing is used and an acceleration technique is applied to the series summation in the Green's functions. The numerical results are compared with the measurements to verify the correctness of the present analysis.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.222-229
• /
• 2000

The purpose of this study is to evaluate and make a comparison between the Ordinary Moment Resisting Frames using different analytical joint model for the Nonlinear response. For this purpose, 3-story structure was designed according to NEHRP 1994 Guidelines. And the center-line dimension model and model considering panel zone were used as analytical model for the structure. Nonlinear Static Procedure and Nonlinear Dynamic Procedure were used to evaluate seismic capacities and demands. The limitation in FEMA 273 was used as the variable number to predicte seismic demands of OMRFs. This analytical studies were performed with DRAIN-2DX modified by Shan Shi. Using the above results, the performance evaluation and seismic demands of OMRFs shall be performed. Finally NSP and NDP shall be compared.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.688-693
• /
• 2001

It is almost impossible to have a straight web for processing in the continuous process systems. The cambered web usually causes the strip walking and damage during process. It is necessary to identify the lateral dynamics of the cambered web for the precise control of lateral behavior. In this paper, a dynamic model of the lateral behavior for a cambered web is developed by introducing the concept of steering angle equivalent to moment caused by the camber. This model can be extended to include terms associated with moment, induced by roller's tilting, web slippage, and shear force, etc. Using this model, a new feed-forward controller is proposed to enable the on-line camber estimation, which is difficult to be measured directly, and the prediction of lateral deflection caused by camber. Computer simulation study shows that the proposed controller successfully eliminates the effect of camber and has better control performance than that of the existing PID controller.

• Journal of the Korean Wood Science and Technology
• /
• 제45권1호
• /
• pp.53-61
• /
• 2017

본 연구에서는 고강성, 고인성의 경량화된 목질접합부를 제작하기 위하여 슬릿 가공된 기둥부재 중앙에 강판 대용인 목질접합물을 삽입하고 기둥부재와 목질접합물만 결합된 시험편들을 제작하였다. 시험편들은 강판을 사용한 대조군 시험편과 모멘트 저항성능을 비교분석하였다. GFRP보강목질적층판과 핀으로 제작된 시험편들은 강판삽입형 시험편 보다 평균 24% 저하된 최대모멘트가 측정되었으나 양호한 인성이 관찰되었다. 파괴형상은 기둥부재의 연단부분에서 연륜을 따라 파괴되었다. 집성재와 목질적층판을 접착제로 일체화한 강절형 시험편은 대조군 시험편보다 초기강성이 2.8배 향상되었고, 최대모멘트도 평균 40% 향상된 경향을 보였다. 강절형 시험편들은 접착층 주위에서 파단되었다.

• 한국강구조학회 논문집
• /
• 제23권5호
• /
• pp.547-555
• /
• 2011

무보강 상 하부 ㄱ형강 접합부는 중 저층 강골조의 시공에 적합한 부분강접 접합부의 한 형태이다. 무보강 상 하부 ㄱ형강 접합부의 초기회전강성뿐만 아니라 소성휨모멘트 지지능력은 실제 설계 및 시공에 있어서 매우 중요한 인자로 이에 대한 예측이 반드시 필요하다. 따라서 그동안 진행된 무보강 상 하부 ㄱ형강 접합부에 대한 연구는 초기회전강성 및 소성휨모멘트 지지능력에 영향을 미치는 접합부의 기하학적 형상을 변화시키면서 거동양상을 파악하였다. 이 연구에서는 AISC LRFD Spec.에서 정의한 Type A 형태 접합부의 상부 ㄱ형강의 두께 및 고력볼트 게이지 거리를 변수로 하여 접합부 실험을 수행하여 휨모멘트 지지능력을 파악하였고, 이를 바탕으로 소성휨모멘트 지지능력 예측을 위한 해석모델을 제안하고자 진행하였다. 해석모델 적용의 타당성은 타 연구자가 수행한 접합부 실험결과와 비교 검토함으로써 입증하였다.

• Steel and Composite Structures
• /
• 제7권2호
• /
• pp.87-103
• /
• 2007

This paper presents some of the results from an experimental research project on the behavior of extended end-plate connections subjected to moment conducted at the Structural Laboratory of Jordan University of Science and Technology. Since the connection behavior affects the structural frame response, it must be included in the global analysis and design. In this study, the behavior of six full-scale stiffened and unstiffened cantilever connections of HEA- and IPE-sections has been investigated. Eight high strength bolts were used to connect the extended end-plate to the column flange in each case. Strain gauges were installed inside each of the top six bolts in order to obtain experimentally the actual tension force induced within each bolt. Then the connection behavior is characterized by the tension force in the bolt, extended end-plate behavior, moment-rotation relation, and beam and column strains. Some or all of these characteristics are used by many Standards; therefore, it is essential to predict the global behavior of column-beam connections by their geometrical and mechanical properties. The experimental test results are compared with two theoretical (equal distribution and linear distribution) approaches in order to assess the capabilities and accuracy of the theoretical models. A simple model of the joint is established and the essential parameters to predict its strength and deformational behavior are determined. The equal distribution method reasonably determined the tension forces in the upper two bolts while the linear distribution method underestimated them. The deformation behavior of the tested connections was characterized by separation of the column-flange from the extended end-plate almost down to the level of the upper two bolts of the lower group and below this level the two parts remained in full contact. The neutral axis of the deformed joint is reasonably assumed to pass very close to the line joining the upper two bolts of the lower group. Smooth monotonic moment-rotation relations for the all tested frames were observed.

• 대한치과교정학회지
• /
• 제14권1호
• /
• pp.75-92
• /
• 1984

This study attempted to analyze the distribution of stress, to examine the bending effect in the mandible according to the pulling directions and determine on which pulling directions are adequate when an orthopedic force was applied to the mandible. An orthopedic force, 500gm, was applied to the gnathion, one point of the chin area, in three directions. The three directions were ; high puli' from gnathion to the center of condyle head, and vertical pull, from gnathion to a parallel line with the posterior border of the ramus, and medium pull, from the gnathion to a parallel line with the lower border of mandible. The distribution of principal stress, bending moment and amount of displacement within the mandible was analyzed by a 3-dimensional finite element method and that of the various portions of mandible were computed and compared according to the pulling directions. The results were as follows : 1. The bending moment of each part of a mandible has been found to be markedly larger in case of vertical pull than in case of either high pull or medium pull. In vertical pull the bending moment turned out to largest at the condyle head and neck portion, the gonial angle portion, the coronoid portion and the ascending ramus portion, respectively, while comparatively large at the cuspid and bicuspid portion and the first molar portion. In case of high pull it was largest at the gonial angle portion and becoming smaller at the coronoid portion, the ascending ramus portion, the condyle head and neck portion, and the cuspid and bicuspid portion, in that order. In case of medium pull, however, the bending moment was largest at the condyle head and neck portion, becoming smaller at the first molar portion, the ascending ramus portion, the coronoid portion, the cuspid and bicuspid portion, and gonial angle portion, in that order. 2. As for the bending effect it was calculated to be mostly oriented downward at the mandibular body and backward at the mandibular ramus in both high pull and vertical pull. In case of medium pull it was oriented upward at the mandibular body and forward at the mandibular ramus. 3. The bending effect also turned out to be mostly oriented outward in case of high pull and medium pull, and inward in vertical pull. 4. At the mandibular body and ramus, the bending effect in the upward-downward direction and that in the forward-backward direction were found to be larger than in the inward-outward direction. 5. If and when we expect any correcting effect on the mandibular protrusion by means of the chin cup appliance, we can say sure as conclusion that high pull and vertical pull are more effective than medium pull.

• 한국전자파학회논문지
• /
• 제13권7호
• /
• pp.702-708
• /
• 2002

역 F형 안테나의 구조와 스퍼 라인 길이에 의해서, 두개의 동작 주파수를 쉽게 결정할 수 있는 이중 주파수 안테나를 설계하였다. 설계된 안테나는 cellular주파수대역에서 동작하는 역 F형 안테나에 PCS 주파수대역에서 동작하는 스퍼 라인을 부하로 이용함으로써 이중 주파수 동작 특성을 갖도록 하였다. 안테나의 설계는 모멘트법을 기본 이론으로 하는 IE3D 상용 프로그램을 사용하였으며, 실제 제작하여 안테나의 반사 손실, 입력 임피던스, 복사패턴, 이득을 측정하였다. 설계된 안테나는 전체 크기가 40 mm $\times$ 14 mm $\times$ 9.4 mm로써 단말기 내장용 안테나로 사용이 가능하며, 국내 cellular 및 PCS에 적용이 가능한 안테나 특성을 나타내고 있다.

• Journal of the Korean Statistical Society
• /
• 제25권4호
• /
• pp.557-566
• /
• 1996

The aim of this paper is to find a suitable design which minimizes the expected discrepancy: in fitting a first order model fearing quadratic terms as bias where there are more than two correlated responses. Kim and Draper(1994) discussed about choosing a design for straight line fits to two correlated responses The general case with r responses is examined here and the result is applied to a specific case to help understandings.

• 천문학회보
• /
• 제42권1호
• /
• pp.56.2-56.2
• /
• 2017

To maintain turbulence in astrophysical fluids, driving is required. Constraining the driving scale of turbulence is important to identify the driving mechanism and also to obtain more accurate turbulence statistics from observations. We discuss how to obtain the driving scale of turbulence from observations. First, we explain the method to obtain the driving scale from the standard deviation of centroid velocity (i.e. the first moment of the line profile). Second, we discuss other techniques to obtain the driving scale.