• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전력기술부문
• /
• pp.7-9
• /
• 2001

Many developing countries has been voltage unstable and the inter- change capability in Korea is limited by voltage instability. In analyzing voltage stability, load model has been considered as constant power, but actual loads vary as voltage changes. In order to incorporating voltage-dependent load model. we need the low-side of P-V curve that can not be obtained by general load flow algorithm. This paper proposes a modified GCF algorithm to obtain a full low-side of P-V curve and a accurate voltage assessment index considering load model. 5-bus sample system and 19-bus real power system are applied to simulate the proposed GCF. Also. the effect of reactive power compensation is illustrated in same systems.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.113-120
• /
• 2001

A frame slab method has been proved as a possible and profitable construction solution for the urban tunnels with very shallow overburden and the excavation from the surface Is strictly limited. Since this method allows only a small amount of construction activities in the ground surface, the disturbances to the public and the surface traffic can be drastically reduced compared with the ordinary cut-and-cover method. The construction sequences of the method and the some of critical cautions needed are described in detail. Also a comprehensive numerical analysis including 2-D and 3-D analysis have been performed to verify the stability of the ground during the construction. It is revealed from this study that the frame slab method can be a quite successful solution for the shallow overburden tunnelling in urban area.

• 세라미스트
• /
• 제21권1호
• /
• pp.44-54
• /
• 2018

Oxide semiconductor has been spotlighted as a channel material of TFTs in AMLCD as an alternative to Si, due to high mobility ( > $5cm^2/Vs$). It is also one of the strong candidates for TFTs in AMOLED because of high bias stability at amorphous phase. Beyond the advantages mentioned above, oxide semiconductor has many strengths such as transparency, low fabrication temperature and relatively low fabrication cost. For those reasons, the application of oxide semiconductor is not limited to display but can be extended to new types of electronics, for example, transient electronics for human implantable devices. From this context, oxide materials that have been used as semiconductor and insulator at transient electronics are investigated respectively, and conductor and substrate candidates are also explained, since transient electronics require systematic consideration beyond individual oxide films.

• Nuclear Engineering and Technology
• /
• 제51권1호
• /
• pp.146-154
• /
• 2019

An improved principal component analysis (PCA) method is applied for sensor fault detection and isolation (FDI) in a nuclear power plant (NPP) in this paper. Data pre-processing and false alarm reducing methods are combined with general PCA method to improve the model performance in practice. In data pre-processing, singular points and random fluctuations in the original data are eliminated with various techniques respectively. In fault detecting, a statistics-based method is proposed to reduce the false alarms of $T^2$ and Q statistics. Finally, the effects of the proposed data pre-processing and false alarm reducing techniques are evaluated with sensor measurements from a real NPP. They are proved to be greatly beneficial to the improvement on the reliability and stability of PCA model. Meanwhile various sensor faults are imposed to normal measurements to test the FDI ability of the PCA model. Simulation results show that the proposed PCA model presents favorable performance on the FDI of sensors no matter with major or small failures.

• 한국분무공학회지
• /
• 제26권4호
• /
• pp.204-211
• /
• 2021

Lean combustion performance of natural gas and hydrogen was compared in a spark-ignition engine. The lean combustion engine operation with natural gas was limited due to combustion instability at an excess air ratio (EAR) above 1.8. The total hydrocarbon (THC) emissions increased significantly with increasing EAR. The nitrogen oxides (NO_X) emissions were also high due to the limitation of increasing EAR. The lean combustion engine operation with hydrogen showed superior combustion stability as well as low THC and NO_X emissions, even at high EARs. However, boosting technology was required to reach the high EARs.

• 진공이야기
• /
• 제4권3호
• /
• pp.16-20
• /
• 2017

Graphene has emerged as a promising material for optoelectronic applications including as ultrafast and broadband photodetector, optical modulator, and nonlinear photonic devices. Graphene based devices have shown the feasibility of ultrafast signal processing for required for photonic integrated circuits. However, on-chip monolithic nanoscale light source has remained challenges. Graphene's high current density, thermal stability, low heat capacity and non-equilibrium of electron and lattice temperature properties suggest that graphene as promising thermal light source. Early efforts showed infrared thermal radiation from substrate supported graphene device, with temperature limited due to significant cooling to substrate. The recent demonstration of bright visible light emission from suspended graphene achieve temperature up to ~3000 K and increase efficiency by reducing the heat dissipation and electron scattering. The world's thinnest graphene light source provides a promising path for on-chip light source for optical communication and next-generation display module.

• 로봇학회논문지
• /
• 제3권1호
• /
• pp.73-80
• /
• 2008

Many researchers are studying on humanoid robots in all over the world. However the humanoid robots are still limited in doing works like picking up objects on the ground or moving rapidly. In this study, a humanoid robot based on the wheel-driving was developed. It can operate with a human working area keeping the stability. Also, the developed robot can take up the object on the floor since it has knee(1DoF) and waist(3DoF), and do service quickly and steadily. The hardware and software structure and algorithms of the developed robot, SEROPI are introduced in this paper.

• Journal of Electrical Engineering and Technology
• /
• 제11권5호
• /
• pp.1116-1127
• /
• 2016

• Progress in Superconductivity
• /
• 제13권1호
• /
• pp.58-63
• /
• 2011

Recently, superconductor flywheel energy storage systems (SFESs) have been developed for application to a regenerative power of train, a power quality improvement, the storage of distributed power sources such as solar and wind power, and a load leveling. As the high temperature superconductor (HTS) bearings offer dynamic stability without the use of active control, accurate analysis of the HTS bearing is very important for application to SFESs. Mechanical property of a HTS bearing is the main index for evaluating the capacity of an HTS bearing and is determined by the interaction between the HTS bulks and the permanent magnet (PM) rotor. HTS bearing rotor consists of PM and iron collector and the proper dimension design of them is very important to determine a supporting characteristics. In this study, we have optimized a rotor magnet array, which depends on the limited bulk size and performed various dimension layouts for thickness of the pole pitch and iron collector. HTS bearing rotor was installed into a single axis universal test machine for a stiffness test. A hydraulic pump was used to control the amplitude and frequency of the rotor vibration. As a result, the stiffness result showed a large difference more than 30 % according to the thickness of permanent magnet and iron collector. This is closely related to the bulk stiffness controlled by flux pining area, which is limited by the total bulk dimension. Finally, the optimized HTS bearing rotor was installed into a flywheel system for a dynamic stability test. We discussed the dynamic properties of the superconductor bearing rotor and these results can be used for the optimal design of HTS bearings of the 10kWh SFESs.

• 디지털융복합연구
• /
• 제17권12호
• /
• pp.319-327
• /
• 2019

본 연구에서는 기능적 전기 자극을 이용한 생체되먹임 융합 자세조절 훈련을 중재하여 급성기 뇌졸중 환자들의 다리 근활성도와 균형 능력에 미치는 효과에 대하여 알아보고자 하였다. 뇌졸중 환자는 기능적 전기 자극을 이용한 생체 되먹임 융합 자세조절 실험군 15명과 일반적인 생체되먹임 융합 자세조절 대조군 15명으로 나누어 8주간 주 5회, 30분간 시행하였고, 다리 근활성도를 평가하기 위해 근전도를 이용하여 가쪽넓은근, 안쪽넓은근, 넙다리곧은근, 넙다리두갈래근를 측정하였다. 균형 능력을 측정하기 위해 Biorecue를 이용하여 균형 능력을 측정하였다. 다리 근활성도 비교에서는 가쪽넓은근, 안쪽넓은근, 넙다리곧은근, 넙다리두갈래근에서 통계적으로 유의한 차이를 보였고, 균형 능력 비교에서는 신체 중심 이동면적, 총 궤적 길이, 안정선한계에서 통계적으로 유의한 차이를 보였다. 이에 따라 기능적 전지 자극을 이용한 생체되먹임 자세조절 훈련이 일반적인 생체되먹임 자세조절 훈련 보다 다리 근활성도와 균형 능력을 향상시키는데 효과적임을 알 수 있었다.