• 오토저널
• /
• 제15권2호
• /
• pp.121-129
• /
• 1993

Plane strain punch stretching test (PSST) was developed to evaluate stamping formability of sheet materials. In this test, the rectangular specimen of sheet material is uniformly stretched up to fracture by raising a specially designed punch to certainly assure plane strain stretching deformation along the longitudinal direction of the specimen. The stamping formability was evaluated by limit punch height(LPH) in plane strain punch stretching test compared to limit dome height(LDH) in hemispherical punch stretching test. LPH-value in PSST well ranks the stamping formability of various material and correlates with press performance. Moreover by using ultrasonic thickness gauge the plane strain intercept-limit plane strain(FLCo)-in forming limit curve can be accurately determined from thickness measurement around the fracture area. The FLCo derived from thickness measurement well correlates with the results from circle grid analysis for the deformed circle grid marked on the surface of the specimen.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1572-1579
• /
• 2005

New procedure for evaluation of creep reduction factor using performance limit strain concept was introduced and confirmed through the creep test results. To determine the performance limit strain of the textile geogrid used in this study, the Sherby-Dorm Plots were applied and the results were compared with the results that applied existed limit strain criteria (GRI test method GG-4). The limit creep strain of the geogrid samples that determined by using the Sherby-Dorm Plots were all 11%. This value is more higher than the existed criteria as 10%. From this 11% limit strain the creep reduction factors were calculated at 100,000 hours design. It was resulted in 1.45 for all of the geogrid samples(8t/m, 10t/m). Finally, when it was compared with the creep reduction factors that using 10% criteria, there were some decrease of reduction factor values about $0.06{\sim}0.14$.

• 소성∙가공
• /
• 제27권2호
• /
• pp.115-122
• /
• 2018

Most domestic and international standards on the forming limit diagram (FLD) including ISO 12004-2, use a 'position-dependent method,' which determines the forming limit from a strain distribution measured on the specimen after necking or fracture. However, the position-dependent method has inherent problems such as the incidence of asymmetry of a strain distribution, the estimation of missing data near fracture, the termination time of test, and the deformation due to the new stress equilibrium after a fracture, which is blamed for causing sometimes a significant lab-to-lab variation. The 'time-dependent method,' which is anticipated to be a new international standard for evaluating the forming limit, is expected to greatly improve these intrinsic disadvantages of the position-dependent method. It is because the time-dependent method makes it possible to identify and accurately determine the forming limit, just before the necking point from the strain data as continuously measured in a short time interval. In this study, we propose a new time-dependent method based on a Gaussian fitting of strain acceleration with the introduction of 'normalized correlation coefficient.' It has been shown in this study that this method can determine the forming limit very stably and gives a higher value, which is in comparison with the results of the previously studied position-dependent and time-dependent methods.

• 대한기계학회논문집A
• /
• 제25권7호
• /
• pp.1107-1118
• /
• 2001

The forming limit diagram introduced by Keeler and Goodwin has been used generally to analyze the formability of sheet metal. However, path dependent forming limit curves based on the state of strain can be explained only by a single criterion which is based on the state. In this study, experimental forming limits in strain space of some metal sheets are transformed into forming limit curves in stress space. Effects of yield criterion are investigated in transforming the forming limit curves. Some important design aspects which are based on the close prediction of movements in forming limit curves during sheet forming are concluded.

• 한국안전학회지
• /
• 제5권2호
• /
• pp.58-65
• /
• 1990

The purpose of this study is to consider the effects of strain rate on the stress-strain behavior of sheet metal at instability. The results and conclusions obtained as follows ： 1. As the strain rate increases, the fracture pressure increases and the polar height at fracture decreases. 2. The effect of strain rate on forming limit diagram produces a general lowering of the diagram with increasing strain rate but changes according to materials and strain paths. 3. The forming limit diagram predicted by swift instability theory is comparatively inconsistent with the experimental result at high strain rates, because there is inevitable gap between them.

• 소성∙가공
• /
• 제22권6호
• /
• pp.328-333
• /
• 2013

The current study aims to determine the limit strains more accurately and reasonably when producing a forming limit curve (FLC) from experiments. The international standard ISO 12004-2 in its recent version (2008) states that the limit major strain should be determined by using the best-fit inverse second-order parabola through the experimental strain distribution. However, in cases where fracture does not occur at the center of the specimen, due to insufficient lubrication, the inverse parabola does not give a realistic fit because of its intrinsic symmetry in shape. In this study it is demonstrated that an inverse quartic function can give a much better fit than an inverse parabola in almost all FLC test samples showing asymmetric strain distributions. Using a quartic fit creates more reliable FLCs.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.935-943
• /
• 1988

본 연구에서는 유압벌지시험기를 이용한 저속 벌지시험과 낙하해머(drop hammer)를 응용한 충격벌지시험기를 제작, 사용하여 충격벌지시험을 하여 저속변형과 충격변형에서 판재금속의 성형한계선도를 구하고 변형율속도가 판재의 불안정 및 성형 성에 미치는 영향을 조사하고 다이의 형상비(단축/장축)를 0.5, 0.75, 1.0 등으로 달 리하여 실험하므로써 변형경로에 따른 한계변형율의 변화를 관찰하고 아울러 기존의 성형한계이론과 비교, 검토하였다.

• 소성∙가공
• /
• 제14권6호
• /
• pp.527-532
• /
• 2005

Among the failure modes which can occur in tube hydroforming such as wrinkling, bursting or buckling, the bursting by local instability under excessive tensile stresses is irrecoverable phenomenon. Thus, the accurate prediction of bursting condition plays an important role in producing the successfully hydroformed part without any defects. As the classical forming limit criteria, strain-based forming limit diagram (FLD) has widely used to predict the failure in sheet metal forming. However, it is known that the FLD is extremely dependant on strain path throughout the forming process. Furthermore, The application of FLD to hydroforming process, where strain path is no longer linear throughout forming process, may lead to misunderstanding for fracture initiation. In this work, stress-based forming limit diagram (FLSD), which is strain path-independent and more general, was applied to prediction of forming limit in tube hydroforming. Combined with the analytical FLSD determined from plastic instability theory, finite element analyses were carried out to find out the state of stresses during hydroforming operation, and then FLSD is utilized as forming limit criterion. In addition, the approach is verified by a series of bulge tests in view of bursting pressure and shows a good agreement. Consequently, it is shown that the approach proposed in this paper will provide a feasible method to satisfy the increasing practical demands for judging the forming severity in hydroforming processes.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.92-96
• /
• 2005

Among the failure modes which can be occurred in tube hydroforming such as wrinkling, bursting or buckling, the bursting by local instability under excessive tensile stresses is irrecoverable phenomenon. Thus, the accurate prediction of bursting condition plays an important role in producing the successfully hydroformed part without any defects. As the classical forming limit criteria, strain-based forming limit diagram has widely used to predict the failure in sheet metal forming. However, it is known that the FLD is extremely dependant on strain path throughout the forming process. Furthermore, the path-dependent limitation of FLD makes the application to hydroforming process, where strain path is no longer linear throughout forming process, more careful. In this work, stress-based forming limit diagram (FLSD), which is strain path-independent and more general, was applied to prediction of forming limit in tube hydroforming. Combined with the analytical FLSD determined from plastic instability theory, finite element analyses were carried out to find out Ihe state of stresses during hydroforming operation, and then FLSD is utilized as forming limit criterion. In addition, the approach is verified with a series of bulge tests in view of bursting pressure and shows a good agreement. Consequently, it is shown that the approach proposed in this paper will provide a feasible method to satisfy the increasing practical demands for judging the farming severity in hydroforming processes.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.285-288
• /
• 2009

The purpose of this study is to predict the forming limit diagram (FLD) of strain-rate sensitive materials on the basis of the Marciniak and Kuczynski (M-K) theory. The strain-rate effect is taken into consideration in such a way that the stress-strain curves for various strain-rates are inputted into the formulation as point data, not as curve-fitted models such as power function. Tensile tests and R-value tests were carried out at several levels of temperature and strain-rate from $25^{\circ}C$ to $300^{\circ}C$ and 0.16 to 0.00016/s, respectively to obtain the mechanical properties of AZ31B magnesium alloy sheet. The FLD of this material was experimentally obtained by limit dome height tests with the punch velocity of 0.1 and 1.0 mm/s at $250^{\circ}C$. The M-K theory-based FLD predicted using Yld2000-2d yield criterion was compared with the experimental results.