• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.294-297
• /
• 2006

Using a single LC panel and two lighting systems, we have developed an advanced LCD system called "Double-Sided LCD." It has only one LC panel and two lighting systems, but it can display images of the same size and resolution on both the front and the rear side. Furthermore, utilizing a simple and thin lighting system we have reduced dramatically its module thickness up to 3.0mm, much thinner than that of conventional dual-type LCD, which is quite appropriate for the use of mobile applications.

• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.193-198
• /
• 2011

In this paper, we used optoelectronic feedback to generate the carrier frequency for the ASK modulation of a lighting LED. A solar cell was used for photo-detector in the feedback circuit, and the LED light was ASK modulated by controlling the ON/OFF state of the switch that is installed in the feedback loop. The oscillation frequency of the optoelectronic feedback loop was about 50 kHz and the data rate of the ASK modulation was 9.6 kbps. In experiments, the optoelectronic feedback circuit was used for the ASK modulation of a lighting LED in the transponder of a visible light identification system, and data exchange between the transponder and the reader was successfully carried out.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.1-6
• /
• 2008

It is important to grasp the accurate lighting level for appropriate maintenance of the road lighting equipment. It is developed 2 division illuminance measurement systems. This system has a small size and no need to block the way and achieves the speedy measurement and high accuracy data in automatically measurement. As a result, this system can save expense and time to measure roadway lighting.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.555-558
• /
• 2017

In this paper, we designed a power supply AC LED driving device which can display uniform power consumption and light efficiency even when AC power of different size is applied. By setting input voltages and deviations of different sizes, it is confirmed that the electric light characteristics are the same at two input voltages. In addition, according to peak voltage of AC power, improper lighting caused in specific LED section is improved, and LED lighting of all sections is implemented in all commercial AC input voltage.

• Journal of the Korean Solar Energy Society
• /
• v.26 no.3
• /
• pp.33-43
• /
• 2006

Daylight dimming control system was analyzed for an indirect lighting system in a small office space with a double skin envelope system. Computer simulations were performed for photosensors with three shielding conditions. The photosensors were placed on the center of ceiling, and backwall. Three sky conditions defined by CIE were considered. Overall, control performance was not very excellent for all conditions. Fully-shielded photosensor achieved good control performance for some cases, but partially-shielded and unshielded photosensors failed to achieve target illuminance. The variation in desktop illuminance due to daylight was examined for a variety of daylight conditions. Linear correlation between desktop illuminance and photosensor illuminance was analyzed using ANOVA.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.4
• /
• pp.1-6
• /
• 2006

The tunnel is the place where brightness changes abruptly. It is important to grasp the road situation and the traffic situation of the tunnel accurately for safe and secure driving, and tunnel lighting installation should be well maintained. Luminance and illuminance of the tunnel inside should be measured periodically to maintain enough brightness. But traditional manual measurement could not guarantee the fastness and trustworthy of the measured values. In this paper, a mobile measuring system for tunnel lighting luminance and illuminance was developed and a result regarding the propriety of the system was derived.

• Journal of Convergence for Information Technology
• /
• v.8 no.5
• /
• pp.153-158
• /
• 2018

In this paper, we have studied a dimming level control method to satisfy both lighting and communication performance in visible light communication system. In the case of the most commonly used OOK and RZ-OOK modulation schemes, continuous Burst Zero Duration will seriously degrade the lighting function. This causes not only the illumination but also the performance of the entire system to deteriorate. Through this study, we analyzed the dimming level characteristics of the existing system and proposed the Illegal Pulse Insertion (IPI) algorithm as a technique to increase the dimming level. Through this, it is possible to effectively control the dimming level and improve the QoS of both lighting and communication by resolving the flicker phenomenon and dimming level reduction in the existing modulation and demodulation system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.3
• /
• pp.231-242
• /
• 2011

This study examines influences of a daylight dimming control system on the variation of indoor illuminance and lighting energy savings in a small office space. Field measurements and a series of computation were performed for typical types of sky conditions in summer. Results indicate that the daylight illuminance under clear and partly-cloudy sky were close to the target illuminance during a majority of time due to a higher ratio of window to wall. However, the target illuminance was not kept successfully due to the variation of photosensor signals which were strongly influenced by desktop illuminance. The system with partially-shielded conditions succeeded to keep target illuminance under clear sky conditions. The system failed under overcast sky conditions since the electric light output from fixtures caused excessive signals to photosensors due to insufficient daylight on a desktop. Unshielded and fully-shielded conditions were not recommended for effective controls of the systems. The influence of lighting fixtures on photosensors should be minimized to achieve successful lighting controls by daylight dimming systems.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.4
• /
• pp.1-6
• /
• 2001

In this paper, it is analysed the spectrum of optical fiber output through the sunlight collector system. As the result of the analysis, the sunlight collector system's UV distribution is lower then the sunlight'UV distribution. Also, the lighting environments under the optical fiber bundles are predicted when applied to the minimum workroom's(6${\times}$6${\times}$2.3[m]) interior lighting by using a lighting design program. In case of optical filer output\`s hight of 1.3[m], the illuminance value over 500[lx] in the area 50${\times}$50[cm] was achieved. As the result its feasibility as an interior lighting source shows no serious problem except the system cost.

• Journal of Biosystems Engineering
• /
• v.25 no.3
• /
• pp.213-220
• /
• 2000

Grafting of fruit-bearing vegetables has been widely used to increase the resistance to soil-borne diseases, to increase the tolerance to low temperature or to soil salinity, to increase the plant vigor, and to extend the duration of economic harvest time. After grafting, it is important to control the environment around grafted seedlings for the robust joining of a scion and rootstock. Usually the shading materials and plastic films are used to keep the high relative humidity and low light intensity in greenhouse or tunnel. It is quite difficult to optimally control the environment for healing and acclimation of grafted seedlings under natural light. So the farmers or growers rely on their experience for the production of grafted seedling with high quality. If artificial light is used as a lighting source for graft-taking of grafted seedlings, the light intensity and photoperiod can be easily controlled. The purpose of this study was to develop a prototype system for the graft-taking enhancement of grafted seedlings using artificial lighting and to investigate the effect of air current speed on the distribution of air temperature and relative humidity in a graft-taking enhancement system. A prototype graft-taking system was consisted by polyurethane panels, air-conditioning unit, system controller and lighting unit. Three band fluorescent lamps (FL20SEX-D/18, Kumho Electric, Inc.) were used as a lighting source. Anemometer (Climomaster 6521, KANOMAX), T-type thermocouples and humidity sensors (CHS-UPS, TDK) were used to measure the air current speed, air temperature and relative humidity in a graft-taking system. In this system, air flow acted as a driving force for the diffusion of heat and water vapor. Air current speed, air temperature and relative humidity controlled by a programmable logic controller (UP750, Yokogawa Electric Co) and an inverter (MOSCON-G3, SAMSUNG) had an even distribution. Distribution of air temperature and relative humidity in a graft-taking enhancement system was fairly affected by air current speed. Air current speed higher than 0.1m/s was required to obtain the even distribution of environmental factors in this system. At low air current speed of 0.1m/s, the evapotranspiration rate of grafted seedlings would be suppressed and thus graft-taking would be enhanced. This system could be used to investigate the effects of air temperature, relative humidity, air current speed and light intensity on the evaportranspiration rate of grafted seedlings.