• Proceedings of the Optical Society of Korea Conference
• /
• 2008.02a
• /
• pp.235-236
• /
• 2008

A configuration of illumination for high-speed color document scanner has been proposed utilizing white light emitting diode and transparent plastic lightguide. The design of illumination system including lightguide for high optical efficiency and uniform image quality is performed based on a simulation using ray-tracing method. The device characteristics are also experimentally evaluated in terms of illumination distribution against longitudinal and transverse direction on document plane. Uniform illumination distribution about 85% of in longitudinal and transverse direction is realized by control of mechanical dimension and position of lightguide.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.71-76
• /
• 2015

Recently, light emitting diodes (LEDs) have been studied to improve their efficiencies for the uses in various fields. Particularly in the aspect of chip structure, via hole type vertical LED chip is developed for improvement of light output power, and heat dissipations. However, current vertical type LEDs have still drawback, which is current concentration around the n-contact holes. In this research, to solve this phenomenon, we introduced isolation layer under n-contact electrodes. With this sub-electrode, even though the active area was decreased by about 2.7% compared with conventional via-hole type vertical LED, we could decrease the forward voltage by 0.2 V and wall-plug efficiency was improved approximately 4.2%. This is owing to uniform current flow through the area of n-contact.

• Journal of Surface Science and Engineering
• /
• v.41 no.5
• /
• pp.199-204
• /
• 2008

Indium tin oxide (ITO) has been commonly used as an anode for organic light emitting diode (OLED), because of its relatively high work function, high transmittance, and low resistance. The ITO was mostly deposited by capacitive type DC or RF sputtering. In this study we introduced a new facing target sputtering method. On applying this new sputtering method, the effect of fundamental deposition parameters such as substrate heating and post etching were investigated in relation to the resultant I-V-L characteristics of OLED. Three kinds of ITOs deposited at room temperature, at $400^{\circ}C$ and at $400^{\circ}C$ with after surface modification by $O_2$ plasma etching were compared. The OLED on ITO deposited with substrate heating and followed by etching showed better I-V-L characteristics, which starts to emit light at 4 volts and has luminescence of $65\;cd/m^2$ at 9 volts. The better I-V-L characteristics were ascribed to the relevant surface roughness with uniform micro-extrusions and to the equi-axed micromorphology of ITO surface.

• Journal of the Optical Society of Korea
• /
• v.15 no.4
• /
• pp.362-367
• /
• 2011

Organic ($Alq_3$) film, which was coated on a donor plate, was transferred to an organic light emitting diode (OLED) substrate with help of heat generated by a dithering laser beam. The laser beam was diffracted in an acousto-optic modulator (AOM), then focused on the laser-to-heat converting layer of the donor plate; the focused spot followed trajectories guided by rotation of a Galvano-mirror. Three different functional waveforms, sine wave, square wave, and saw tooth wave were applied to the AOM as modulation signal to generate the dithering beam. The fluorescence microscope images of the donor plate showed that the patterns of removed $Alq_3$ film were affected considerably by the modulation waveforms and the phase difference between adjacent dithering beams. Further, the printed images of Alq3 film on the OLED substrate were different from the patterns of removed Alq3 film. Atomic force microscope images indicated that not only direct transfer but also deposition by sublimated vapor of Alq3 contributed to the pattern formation. Printed patterns affected considerably the electricity-to-light conversion characteristics of OLEDs. For uniform transfer, not only the phase relation of dithering beam lines but also adequate waveform were important.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1089-1097
• /
• 2006

The market demand of display devices is drastically increasing in the information technology age. The research on OLED (Organic Light Emitting Diodes) display with the luminescence in itself is being more paid attention than LCD (Liquid Crystal display) with the light source from the back. The vapor deposition process is most essential in manufacturing OLED display. The temperature distribution of the linear cell in this process is closely related to securing the uniformity of organic materials on the substrate. This work analyzed the temperature distribution depending on the intervals between the crucible and the heating band as well as on the amount of the heat flux from the heating band. Moreover, the roles of the water jacket and the configuration of the cover within the linear cell were examined through the temperature analysis for six configurations of the linear cell. Under the above temperature analysis, the variations in the intervals and the amount of the heat flux were considered to have an effect on building the uniform temperature distribution within the crucible. It is predicted that the water jacket and the adequate configuration of the cover will prevent the blowout and clogging phenomena, respectively. The results can be used as the fundamental data for designing the optimal linear cell.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.3
• /
• pp.12-17
• /
• 2011

In this paper, we report on the improved electrical and optical characteristics for decreasing current crowding effect and uniform current distribution by designing octagonal finger type electrode pattern in large-scale lateral GaN (Gallium Nitride) LED (Light-emitting diode) with numerical 3-D simulator. Compared with the conventional electrode pattern, proposed electrode pattern was investigated to confirm the improvement of characteristics. From the simulation results of 3-D SpeCLED/RATRO simulator, we found that the forward voltage was decreased by 0.34 V and the light output power was improved by 7.72 mW at the same injection current condition in the LED with proposed octagonal finger type electrode.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.66-69
• /
• 2007

We have investigated printing techniques for processing organic light-emitting diodes (OLEDs). We succeeded to gravure print uniform organic thin films as well as screen print low work function cathode for OLED structure. Furthermore, by using roll-to-roll manufacturing methods, we have been able to fabricate all-printed flexible OLED demonstrator.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.12
• /
• pp.27-34
• /
• 2005

We have investigated the correlation between the active-layer uniformity and reliability of InGaN/GaN blue LEDs. According to initial characteristics, the devices are classified into two groups: group I devices of uniform light-emission and group II devices of non-uniform light-emission. The group II devices are more dependent on temperature and we have found two degradation mechanisms through reliability test. One is bulk degradation in which the degradation occurred over the entire chip and another one is edge degradation in which the degradation occurred from the edge of the chip. Bulk degradation caused by the nonradiative defects is found to be faster in group II devices while there is no difference in the rate of the much faster edge degradation, where darkening starts from the n-Ohmic contact edge. Therefore, more uniform active layer, more uniform current spreading, and the passivation of the dry-etched side-wall are essential for the high reliability of InGaN/GaN LEDs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.4
• /
• pp.725-729
• /
• 2003

In this paper, a mercury-free flat discharge lamp with opposite electrode structure, a couple of phosphor layer and discharge vessel has been studied for LCD back-lighting. When the drive voltage conditions were set properly, a uniform discharge generates over entires emitting surface. The firing voltage was increased with increasing the discharge gas pressure. It was considered that this tendency was resulted from the decrease of mean free paths due to the increase of discharge gas pressure. The maximum luminance of 2700[cd/m2] was obtained in the green emitting FFL.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.464-468
• /
• 2012

Three solvent systems, chlorobenzene (ink 1), chlorobenzene/o-dichlorobenzene (ink 2) and chlorobenzene/tetrahydronaphthalene (ink 3), were compared as printable inks for the fabrication of polymer light-emitting diodes (PLEDs) using poly[2-methoxy-5-(2-ethylhexyl-oxyl)-1,4-phenylenevinylene (MEH-PPV) as an emissive material and an inkjet printer (Fujifilm Dimatix DMP-2831). Ink 1 clogged the printer's nozzle and gave non-uniform film. Inks 2 and 3 were used to fabricate PLEDs with ITO/PEDOT:PSS/MEH-PPV/LiF/Al configurations. The best performance (turn-on voltage, 3.5 V; luminance efficiency, 0.17 cd/A; luminance, 1,800 cd/m) was obtained when ink 3 was used to form the emissive layer (thickness, 49 nm), attributable to the better morphology and suitable thickness of the MEH-PPV layer.