• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.1
• /
• pp.76-79
• /
• 2015

Visible light communication (VLC) is a short range optical communication technology using light emitting diodes. In this paper, we implement variable pulse position modulation (VPPM) defined in the IEEE 802.15.7 standard with a Cortex-M processor, which is a new modulation scheme for VLC providing a dimming control mechanism for flicker-free optical communication. The synchronization procedure between the transmitter and receiver is not defined clearly in the VPPM standard. In order to synchronize the transmitter and receiver easily, two overhead bits are used including one start bit and one stop bit modulated by on-off keying (OOK). Experimental results under various environmental conditions show that the proposed VPPM can support a seamless 100 Kbps data rate with 10 levels in the dimming control.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.860-863
• /
• 2003

Pulse oximetry has gained wide spread clinical acceptance in the latter part of the 21st century. The principle of pulse oximetry is based on the red and infrared light absorption features and uses a light emitter with red and infrared LEDs that shines through a reasonably translucent site with good blood flow. There are two methods of sending light through the measuring site : transmission and reflectance. After the transmitted red and infrared signals pass through the measuring site and received at the photodetector, the red/infrared ratio is calculated. But, pulse of oximeters are so sensitive that they may detect pulses when pressure is too low to provide adequate tissue blood flow, that is, SpO2 may decrease due to O2 consumption by the finger of the pulsing but stagnant arterial blood at low pressure or with vasoconstriction. This project has the limitations of pulse oximetry. Therefore, this paper is focused on the resuction of motion artifact that caused by moving when someone measures with SpO2 system.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.10
• /
• pp.458-463
• /
• 2006

The purpose of this work is to investigate the fundamental properties of the gradual muscle force potentiation. We investigated the dependence of force potentiation on both the pulse-amplitude and the pulse-duration with different ramp-up time. The experimental results showed that the force increment ratio (FIR) during constant electrical stimulation decreased with pulse-amplitude and also with pulse-duration. The FIR was greater with short ramp-up time in both the pulse-amplitude and pulse-width modulation. The feasible mechanism might be that the myosin light chain phosphorylation induces the force potentiation and it occurs only in the fast type muscle fibers which are recruited first. These observations indicate that muscle potentiation must be understood well for the accurate control of muscle force.

• Journal of Welding and Joining
• /
• v.5 no.4
• /
• pp.47-53
• /
• 1987

The purpose of this study is to reexamine our test method in the light ofstatistical methods for data interpretation. Our trial to apply Plackett-Burman statistical model in multifactorial welding experiments shows that is saves much time and cost and extracts very accurate results. In this study, the parametric effects of bead shape on pulse MIG process in Cu-Ni alloy are investigated for verifying our trial.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.1
• /
• pp.67-75
• /
• 1992

A new method of driving the PDP(Plasma Display Panel) was proposed and its characteristics were investigated. Applying high frequency non-discharge pulses to an auxiliary anode resulted an increased region of stable operation, decreased delay time and increased light intensity. It is suggested that PDP with DPM (Double Pulse Memory) drive technique improves the delay time, luminance, region of stable operation and luminous efficacy compared to PDP with PPM(Planar Pulse Memory) drive technique developed by NHK Lab. in Japan.

• Journal of Sensor Science and Technology
• /
• v.22 no.3
• /
• pp.212-218
• /
• 2013

In this paper, we introduce a new method to reduce the inter-channel crosstalk in visible light communication (VLC) systems using the synchronizing pulses transmitted through the power lines. Synchronizing pulses are simultaneously transmitted to multiple VLC transmitters and receivers through the 220V power line. Each VLC transmitter modulates an LED and each VLC receiver demodulates the signal light in the time slot that is allocated with reference to the synchronizing pulses. This method is very simple and effective to prevent the inter-channel crosstalk in VLC systems for sensor networks because every VLC system can easily get the synchronizing pulses from the nearby power line.

• Journal of Sensor Science and Technology
• /
• v.23 no.5
• /
• pp.349-355
• /
• 2014

In this paper, we developed a new method to transmit multiple visible light channels in time division mode using the AC power line frequency in order to prevent the crosstalk between adjacent optical signals. Synchronizing pulses are generated from the 220 V power line, and one pulse period is subdivided into several time slots for visible light channels. Each channel transmits data in a predefined time slot without interfering adjacent channels. In experiments, synchronizing pulses with a repetition rate of 240 Hz were generated from the 60 Hz power line, and three VLC channels with a bit rate of 9.6 kbps transmitted data independently using the time slots between synchronizing pulses. This configuration is very useful in constructing time division VLC networks for multiple sensors.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.652-657
• /
• 1991

Up to date, application areas of mobile robots have been expanded. In addition, Many types of LRF(Laser Range Finder) systems have been developed to acquire three dimensional information about unknown environments. However in real world, because of various noises (sunlight, fluorescent light), it is difficult to separate reflected laser light from these noise. To overcome the previous restriction, we have developed a new type vision system which enables a mobile robot to measure the distance to a object located 1-5 (m) ahead with an error than 2%. The separation and detection algorithm used in this system consists of pulse phase difference method and multi-stripe structured light. The effectiveness and feasibility of the proposed vision system are demonstrated by 3-D maps of detected objects and computation time analysis.

• Journal of Sensor Science and Technology
• /
• v.25 no.5
• /
• pp.303-309
• /
• 2016

In this paper, we introduce a new method for controlling the illumination of LEDs in visible light communication (VLC) by changing the duty cycle of Manchester code. When VLC data were transmitted in Manchester code, the average optical power of the LEDs was proportional to the duty cycle. In experiments, we controlled the illumination of a $3{\times}3$ LED array from 10% to 90% of its peak value by changing the duty cycle of the Manchester code. The synchronizing clocks required for encoding and decoding the Manchester code were supplied by pulse generators that were connected to a 220 V power line. All pulse generators made the same pulses with a repetition frequency of 120 Hz, and they were synchronized with the full-wave rectified voltage of the power line. This scheme is a very simple and useful method for constructing indoor wireless sensor networks using LED light.

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.196-203
• /
• 2021

In this study, an optical identification system was developed, wherein visible light is used to transmit the interrogating signal, and infrared is used to send the response signal. In the reader, visible light from a light emitting diode (LED) array was modulated via modified pulse width modulation for flicker-free illumination and dimming control. Moreover, the duty factor of the dimming control time was employed to control the illumination from the LED. In the transponder, the spike signal in the output of the high-pass filter was utilized to recover the interrogating signal while preventing interference from the 120-Hz noise from adjacent lighting lamps. The illumination was controlled in 26-86% range of the constant wave LED illumination by changing the duty factor from 20% to 90%. This configuration is advantageous for the construction of optical identification systems for automatic security check and car fare calculation at toll gates or parking facilities.