• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.250-253
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. The Ni contact was formed on the front grid pattern by electroless plating followed by anneal ing at $380{\sim}400^{\circ}C$ for $15{\sim}30$ min at $N_{2}$ gas to allow formation of a nickel-silicide in a tube furnace or a rapid thermal processing(RTP) chamber because nickel is transformed to NiSi at $380{\sim}400^{\circ}C$. The Ni plating solution is composed of a mixture of $NiCl_{2}$ as a main nickel source. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. The Ni/Cu contact was found to be well suited for high-efficiency solar cells and was successfully formed by using electroless plating and electroplating, which are more cost effective than vacuum evaporation. In this paper, we investigated low-cost Ni/Cu contact formation by electroless and electroplating for crystalline silicon solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.470-470
• /
• 2013

Recently, active materials such as amorphous silicon (a-Si), poly crystalline silicon (poly-Si), transition metal oxide semiconductors (TMO), and organic semiconductors have been demonstrated for flexible electronics. In order to apply flexible devices on the polymer substrates, all layers should require the characteristic of flexibility as well as the low temperature process. Especially, pentacene thin film transistors (TFTs) have been investigated for probable use in low-cost, large-area, flexible electronic applications such as radio frequency identification (RFID) tags, smart cards, display backplane driver circuits, and sensors. Since pentacene TFTs were studied, their electrical characteristics with varying single variable such as strain, humidity, and temperature have been reported by various groups, which must preferentially be performed in the flexible electronics. For example, the channel mobility of pentacene organic TFTs mainly led to change in device performance under mechanical deformation. While some electrical characteristics like carrier mobility and concentration of organic TFTs were significantly changed at the different temperature. However, there is no study concerning multivariable. Devices actually worked in many different kinds of the environment such as thermal, light, mechanical bending, humidity and various gases. For commercialization, not fewer than two variables of mechanism analysis have to be investigated. Analyzing the phenomenon of shifted characteristics under the change of multivariable may be able to be the importance with developing improved dielectric and encapsulation layer materials. In this study, we have fabricated flexible pentacene TFTs on polymer substrates and observed electrical characteristics of pentacene TFTs exposed to tensile and compressive strains at the different values of temperature like room temperature (RT), 40, 50, $60^{\circ}C$. Effects of bending and heating on the device performance of pentacene TFT will be discussed in detail.

• Current Photovoltaic Research
• /
• v.3 no.2
• /
• pp.54-60
• /
• 2015

ZnSnO thin films were deposited by atomic layer deposition (ALD) process using diethyl zinc ($Zn(C_2H_5)_2$) and tetrakis (dimethylamino) tin ($Sn(C_2H_6N)_4$) as metal precursors and water vapor as a reactant. ALD process has several advantages over other deposition methods such as precise thickness control, good conformality, and good uniformity for large area. The composition of ZnSnO thin films was controlled by varying the ratio of ZnO and $SnO_2$ ALD cycles. The ALD ZnSnO film was an amorphous state. The band gap of ZnSnO thin films increased as the Sn content increased. The CIGS solar cell using ZnSnO buffer layer showed about 18% energy conversion efficiency. With such a high efficiency with the ALD ZnSnO buffer and no light soaking effect, AlD ZnSnO buffer mighty be a good candidate to replace Zn(S,O) buffer in CIGSsolar cells.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.49 no.4
• /
• pp.385-394
• /
• 2013

This study has conducted a comparative analysis on the fishing efficiency of LED fishing lamps by squid jigging vessels, the Yeongrak-ho (16 tons) and Somang-ho (9.77 tons), which operated during September and October 2010 and during October 2011, comparing with MH (Metal Halide) fishing lamp-equipped fishing vessels. This study has also examined vessel's fuel consumption level. The light powers of LED fishing lamps of the Yeongrak-ho and Somang-ho were 25.8kW and 32kW, respectively. Those of the MH fishing vessels, that is, the MH fishing lamp-equipped fishing vessels, were 105kW and 81kW, respectively. The average squid catch in number of an LED vessel, Yeongrak-ho, was 39.2% of the MH fishing lamp-equipped fishing vessels; however, that of the Somang-ho improved to 78.7% of the MH fishing lamp-equipped vessels. Average catch in number by Yeongrak-ho crew was 2.6 times more than catch in number by automatic jigging machines. Average catch in number by MH fishing vessel crew was 1.8 times more than that by automatic jigging machines. An LED vessel, Yeongrak-ho's fishing rate was 17.5%~152.2% of the MH fishing vessels, that is, 61.1% on average, in comparison of combined catch in number per automatic jigging machine and per crewmember. Somang-ho's fishing rate was 6.7%~127.6% of the MH fishing vessels, that is, 73.1% on average. The average fuel consumption level of the Somang-ho, throughout its departure from to arrival at the port, was 475.7l, and that during fishing hours was 109.6l, or 23.0% of the total fuel consumption level. Somang-ho's fuel consumption level per fishing hour was 9.7l on average.

• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.280-284
• /
• 2013

Stress-strain curves are fundamental properties to study characteristics of materials. Flow stress curves of the powder materials are obtained by indirect testing methods, such as tensile test with the bulk materials and powder compaction test, because it is hard to measure the stress-strain curves of the powder materials using conventional uniaxial tensile test due to the limitation of the size and shape of the specimen. Instrumented nanoindentation can measure mechanical properties of very small region from several nanometers to several micrometers, so nanoindentation technique is suitable to obtain the stress-strain curve of the powder materials. In this study, a novel technique to obtain the stress-strain curves using the combination of instrumented nanoindentation and finite element method was introduced and the flow stress curves of Fe powder were measured. Then obtained stress-strain curves were verified by the comparison of the experimental results and the FEA results for powder compaction test.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.3
• /
• pp.175-190
• /
• 2001

We investigated population of the elliptical galaxy NGC 4649 using the spectral synthesis technique based on the linear program in the spectral regions between $3160\AA$to $10800\AA$. We used the spectral data of stars obtained by Gunn & Striker (1983), and the integrated spectrum of NGC 4649 observed by Bertola et al. (1982). Among four models with different main sequence turn-off points, G8-K0V main sequence turn-off model is best fitted to the integrated spectrum of NGC 4649. We also found that super metal rich K giants are needed to describe the absorption lines in the long wavelength regions of integrated spectrum of NGC 4649. The mass to absolute light ratio obtained from the spectral synthesis is ~ 20 similar to those calculated dynamically.

• Korean Journal of Human Ecology
• /
• v.24 no.1
• /
• pp.79-96
• /
• 2015

The purpose of this research was to analyze the clothing behavioral attributes of male music enthusiasts. A questionnaire was developed based on previous researches. Respondents were men who were concerned with music in terms of a job, a major or a hobby. A total of 200 responses were analyzed by SPSS 20.0 through factor analysis with Varimax rotation, ANOVA with post-hoc test(SNK-test) and ${\chi}^2$-test. Music preference was classified into 3 factors: New age/jazz, Hiphop/dance, and Metal rock/ballad factor. 5 Clothing purchasing orientation factors were extruded: hedonic, planned, convenience, brand pursued, and fashion pursued purchasing orientation. Using those factor scores, 3 groups were classified: Group1(G1), preferring Hiphop/dance music with lower hedonic and brand/fashion pursued purchasing orientation; G2, preferring Hiphop/dance music with no interest in clothing shopping and fashion; G3, preferring New age music with high convenience and brand pursued purchasing orientation. In addition, there were significant differences among groups in clothing behavior such as social ostentation, individuality, self-expression, fashionability, conformity; in purchase motivation such as hedonic and trend/designer oriented purchase motivation; in information source like advertisement/media source; and in store choice criteria such as store light/music and popularity. The findings showed even the enthusiasts for the same music showed the different sopping orientation and different clothing behavior, suggesting that a personal value or taste can be a plausible factor to figure out attributes of consumers. An interest/involvement in clothing could be helpful to subdivide the music enthusiasts as the target market.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.21-29
• /
• 2008

We studied both the wavelength and intensity dependent photo-responses (photofield-effect) in amorphous In-Ga-Zn-O (a-IGZO) thin-film transistors (TFTs). During the a-IGZO TFT illumination with the wavelength range from $460\sim660$ nm (visible range), the off-state drain current $(I_{DS_off})$ only slightly increased while a large increase was observed for the wavelength below 400 nm. The observed results are consistent with the optical gap of $\sim$3.05eV extracted from the absorption measurement. The a-IGZO TFT properties under monochromatic illumination ($\lambda$=420nm) with different intensity was also investigated and $I_{DS_off}$ was found to increase with the light intensity. Throughout the study, the field-effect mobility $(\mu_{eff})$ is almost unchanged. But due to photo-generated charge trapping, a negative threshold voltage $(V_{th})$ shift is observed. The mathematical analysis of the photofield-effect suggests that a highly efficient UV photocurrent conversion process in TFT off-region takes place. Finally, a-IGZO mid-gap density-of-states (DOS) was extracted and is more than an order of magnitude lower than reported value for hydrogenated amorphous silicon (a-Si:H), which can explain a good switching properties observed for a-IGZO TFTs.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.119-133
• /
• 1998

To implement full automation in pipe welding, it si most important to develop special sensors and their related systems which act like human operator when detecting irregular groove conditions. In this study, an automatic pipe Gas Metal Arc Welding (GMAW) system was proposed to full control pipe welding procedure with intelligent sensor systems. A five-axes manipulator was proposed for welding torch to automatically access to exact welding position when pipe size and welding angle were given. Pool status and torch position were measured by using a weld-pool image monitoring and processing technique in root-pass welding for weld seam tracking and weld pool control. To overcome the intensive arc light, pool image was captured at the instance of short circuit of welding power loop. Captured image was processed to determine weld pool shape. For weld seam tracking, the relative distance of a torch position from the pool center was calculated in the extracted pool shape to move torch just onto the groove center. To control penetration of root pas, gap was calculated in the extracted pool image, and then weld conditions were controlled for obtaining appropriate penetration. welding speed was determined with a fuzzy logic, and welding current and voltage were determined from a data base to correspond to the gap. For automatic fill-pass welding, the function of human operator of real time weld seam control can be substituted by a sensor system. In this study, an arc sensor system was proposed based on a fuzzy control logic. Using the proposed automatic system, root-pass welding of pipe which had gap variation was assured to be appropriately controlled in welding conditions and in torch position by showing sound welding result and good seam tracking capability. Fill-pass welding by the proposed system also showed very successful result by tracking along the offset welding line without any control of human operator.

• Journal of The Korean Society of Clinical Toxicology
• /
• v.4 no.2
• /
• pp.175-179
• /
• 2006

Welders are exposed to a number of hazards including metal fumes, toxic gases, electricity, heat, noise, and radiation such as ultraviolet and infrared light. We encountered a patient who developed non-cardiogenic pulmonary edema within a day after cutting copper pipe with an oxyethylene torch. The patient was a 26-year-old welder. He complained of dyspnea, generalized myalgia, and febrile sensation the following morning. The patient's chest X-ray and chest CT scan showed extensively distributed and ill-defined centrilobular nodules. Both his symptoms and chest X-ray abnormalities improved spontaneously. We attributed the patient's symptoms to non-cardiogenic pulmonary edema due to nitrogen dioxide, reasoning that: 1) the pipe consisted only of copper, according to material safety data sheet (MSDS); 2) a previous report in the literature demonstrated increased nitrogen dioxide levels under similar conditions; 3) the patient's clinical course and radiologic findings were very reminiscent of non-cardiogenic pulmonary edema following accidental exposure to nitrogen dioxide.