• International Journal of Reliability and Applications
• /
• 제18권2호
• /
• pp.45-63
• /
• 2017

In this paper, we have formulated optimum Accelerated Life Test (ALT) plan for a parallel system with two independent components using masked data with ramp-stress loading scheme and Type-I censoring. Consider a system of two independent and non-identical components connected in parallel. Such a system fails whenever all of its components has failed. The exact component that causes the system to fail is often unknown due to cost and time constraint. For each parallel system at test, we observe its system's failure time and a set of component that includes the component actually causing the system to fail. The stress-life relationship is modelled using inverse power law, and cumulative exposure model is assumed to model the effect of changing stress. The optimal plan consists in finding out the optimum stress rate using D-optimality criterion. The method developed has been explained using a numerical example and sensitivity analysis carried out.

• 한국항공우주학회지
• /
• 제45권8호
• /
• pp.627-638
• /
• 2017

항공기에 탑재된 레이더 장비는 무작위진동 환경에 장기간 노출되어, 설계 시 피로수명 예측이 중요한 요소로 고려된다. 피로수명을 예측하는 방법 중 주파수영역 피로해석 방법이 지속적으로 제안되고 있다. 본 논문은 많이 사용되는 4가지의 주파수영역 피로해석 방법을 선정하여, 시편 피로시험 결과와 비교하였다. Strain gage를 이용한 시편 피로시험을 통해 시간영역 피로해석과 주파수영역 피로해석 방법을 비교한 결과, Dirlik과 Benasciutti-Tovo방법이 주파수영역 피로해석법 중 시간영역 피로해석법과 잘 일치하였다. 시편 피로시험 결과를 토대로 Dirlik과 Benasciutti-Tovo방법과 유한요소모델을 이용하여 항공기 탑재 장비의 피로해석을 수행하였으며, 요구수명이 만족함을 확인하였다.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.120-127
• /
• 2008

A military vehicle undergoes normal to extreme driving conditions, which consequently induce the fatigue and fracture of cabin and frame. So, it is important to estimate the fatigue life of two components at an initial design stage. In this paper, Modal Superposition Method(MSM) was applied to evaluate the durability performance of a small-sized military truck. For reliable durability analysis, a Virtual Test Lab(VTL) Model was established by correlation with experimental results. These data were extracted from actual driving test, modal test, and SPMD(Suspension Parameter Measuring Device) test. This process shows that Virtual Fatigue Analysis can be a useful approach in the development of military vehicles as well as commercial vehicles.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.20-24
• /
• 2006

In this paper we investigated the method of examining the accelerated life test on LED traffic signal module by the temperature. The longevity presumption of the LED type signal light by a general heat cycle test used and executed cycle when it was done to longevity by the heat cycle test number and the acceleration factor of a real system requirements of this heat cycle test. Therefore, it reports on the introduction of the acceleration type from which the LED traffic signal module is done here to clarify the above-mentioned acceleration factor with the object and the acceleration factor is requested the test atmosphere actually in the system requirements.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.147-154
• /
• 2013

This study reports on the development and investigation of a BMS module using a new algorithm on the driving performance and battery life of electric vehicles. Here, the initial SOC was calculated using an open circuit voltage (OCV) method and a current integral method was later applied to the BMS module. We verified the performance of the BMS module by comparing both the results of the in-vehicle test and the BMS simulator test. Our verification test showed good agreement between the results of experiments and simulation with a small error of ${\pm}0.8%$. Here, we confirmed that the present, newly-developed BMS module not only can predict the battery life but can also monitor SOC, pack voltage, and current temperature.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.75-78
• /
• 2000

There are several effective factors to influence die life in the warm forging process. For instance process design die design and die materials etc This study presented heat treatment method which could improve toughness and wear resistance simultaneously in high temperature to apply high speed tool steels like SKH51 to die material for warm forging process. To verify the feasibility of application of heat treatment method mentioned above wear test was performed under the condition of constant time in 40$0^{\circ}C$ Wear coefficient was examined to search a relation between wear amount and time for each material and heat treatment method in 30, 60, and 130 minutes. To quantify the toughness-behavior between room and high temperature impact test was performed and heat fatigue test also fulfilled to compare with the resistance of heat check in room, 200, 400, and $600^{\circ}C$ temperature. On the basis of experimental results mentioned above high speed tool steel was applied to verify appropriateness of newly proposed heat treatment method for die of rotor pole used in automobile alternator. As a result die life of high speed tool steel applied newly proposed heat treatment is longer than that of STD61.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 A
• /
• pp.265-268
• /
• 2000

In this study, a small punch creep (SP-Creep) test using miniaturized specimen has been described for the development of the new creep test method for high temperature structural components such as headers and tubes of boiler, turbine casing and rotor, and reactor vessel. The SP-Creep testing technique has been applied to 1Cr-0.5Mo steel used widely as boiler header material and the creep test temperature are varied at $550^{\circ}C{\sim}600^{\circ}C$. From the experimental results, e.g. SP-Creep curve behaviors, the creep rate in steady state and creep rupture life with test temperature and load, the load exponential value(n, m), the activation energy($Q_{spc}$), the Monkman-Grant relation and the creep life assessment equation etc., it can be summarized that the SP-Creep test may be a useful test method to evaluate the creep properties of the heat resisting material such as boiler header.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3149-3158
• /
• 1994

In this paper, using the formulation of dynamic equivalent load considering the effects of moment load and the equation to estimate the cage rotational speed, the new life equation of deep groove ball bearing under radial and moment loads was proposed. Fatigue life test apparatus with the measuring equipment of shaft and cage speed was designed and developed to be capable of subjecting combined radial and moment load. Fatigue life tests were executed by sudden death test method and the reliability of fatigue lives was evaluated by Weibull distribution analysis. From the results of fatigue tests and analysis, the relationships between film parameters and life adjustment factors were acquired. And it was turned out that so as to estimate the effect of moment load on fatigue life, the life adjustment factor as well as the dynamic equivalent load must be taken into account.

• 한국산업융합학회 논문집
• /
• 제10권3호
• /
• pp.143-147
• /
• 2007

In recents years, the statistical properties has become an important quantity for reliability based design of a component. The effects of the materials and test conditions for parameter estimation in residual strength degradation model are studied in carbon/epoxy laminate. It is shown that the correlation between the experimental results and the theoretical prediction on the fatigue life distribution using the life distribution convergence method is very reasonable.

• International Journal of Reliability and Applications
• /
• 제13권1호
• /
• pp.19-35
• /
• 2012

This paper presents an optimum design of step-stress partially accelerated life test (PALT) plan which allows the test condition to be changed from use to accelerated condition on the occurrence of fixed number of failures. Various life distribution models such as exponential, Weibull, log-logistic, Burr type-Xii, etc have been used in the literature to analyze the PALT data. The need of different life distribution models is necessitated as in the presence of a limited source of data as typically occurs with modern devices having high reliability, the use of correct life distribution model helps in preventing the choice of unnecessary and expensive planned replacements. Truncated distributions arise when sample selection is not possible in some sub-region of sample space. In this paper it is assumed that the lifetimes of the items follow Truncated Logistic distribution truncated at point zero since time to failure of an item cannot be negative. Optimum step-stress PALT plan that finds the optimal proportion of units failed at normal use condition is determined by using the D-optimality criterion. The method developed has been explained using a numerical example. Sensitivity analysis and comparative study have also been carried out.