• Journal of Korean Society of Forest Science
• /
• v.76 no.4
• /
• pp.317-329
• /
• 1987

A comparative anatomy between the secondary xylem in the root and the stem of some Korean Lauraceae, including 6 genera and 7 species, was carried out in this study. The results are as follows; diameter and length of vessel element and fiber are wider and longer in the root than the stem. The angle of end wall of vessel element is more inclined in the root than the stem. Also more number of bar on the perforation plate of vessel element in root wood is found. From the anatomical characters of root and stem wood in some Lauraceous species, it is suggested that the wood of the root is phylogenetically mote primitive than that of the stem, except the diameter of vessel element.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.1
• /
• pp.58-67
• /
• 2003

The characteristics of the commercial garbage-decomposing accelerant, Raw Material of Pomia(RMP), Pomia and Vitabio. were analyzed. In HPLC pattern, Pomia and Vitabio showed main peak of about 30kDa in 280nm wave length. RMP, Pomia and Vitabio showed three, two and two peaks in 210nm. K and Na ion content of RMP were 2,620 and 1,590ppm, respectively, and their content were the largest one among others. Ca, Mg and Mn ion content of RMP were also the largest one, but Zn ion content was the least one. $Cl^{-}$, $F^{-}$ and $NO_3^{-}$ ion content of RMP were the largest one, especially $Cl^{-}$ content was 3,553ppm. pH values of RMP and Pomia were in neutral region, but Vitabio was 9.03. Dried residue content of RMP, Pomia and Vitabio were 1.4%, 0.55% and 0.4%, respectively. The number of general bacteria on PCA plate from RMP, Pomia and Vitabio were 2.2{\times}10^{6}cfu/ml,{\;}6.5{\times}10^{3}cfu/ml{\;}and{\;}1.1{\times}10^{3}cfu/ml$, respectively. The number of facultative anaerobes of RMP was $4.4{\;}{\times}{\;}10^{4}cfu/ml$, and it was biggest one. Lactobacilli and yeasts were found less than 10cfu/ml at best. The bacterium exists in RMP in high frequency was identified as Bacillus subtilis. Volatile sulfur compound amount of garbage samples treated with Pomia and Vitabio in concentration of 1/500 at $33^{\circ}C$ for 8 days were 1,273ppb and 1,902ppb, respectively, and control showed 3,015ppb. Volatile organic compound amount of the garbage samples treated were 68,312ppb, 124,317ppb and 263,954ppm, respectively. Diethylamine that known as malodor compound were 5,107ppb, 261ppb and 11,124ppb, respectively.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.3
• /
• pp.249-255
• /
• 2016

Objective: This purpose of this study was to analyze the relationship between dimensionless leg stiffness and kinetic variables during gait performance, and its modulation with body weight. Method: The study sample consisted of 10 young women divided into 2 groups (Control, n=5 and Obese, n=5). Four camcorders (HDR-HC7/HDV 1080i, Sony Corp, Japan) and one force plate (AMTI., USA) were used to analyze the vertical ground reaction force (GRF) variables, center of pressure (COP), low limb joint angle, position of pelvis center and leg lengths during the stance phase of the gait cycle. Results: Our results revealed that the center of mass (COM) displacement velocity along the y-axis was significantly higher in the obese group than that in control subjects. Displacement in the position of the center of the pelvis center (Z-axis) was also significantly higher in the obese group than that in control subjects. In addition, the peak vertical force (PVF) and dimensionless leg stiffness were also significantly higher in the obese group. However, when normalized to the body weight, the PVF did not show a significant between-group difference. When normalized to the leg length, the PVF and stiffness were both lower in the obese group than in control subjects. Conclusion: In the context of performance, we concluded that increased dimensionless leg stiffness during the gait cycle is associated with increased velocity of COM, PVF, and the change in leg lengths (%).

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.1-7
• /
• 1999

This paper describes the modification of hull bottom for the air lubrication technique to the passenger boat in service at the Chung-Ju lake, which has a large beam-draft ratio. From numerical analysis of 2-D cavity problem by potential theory, the cavity shape, length and the pressure in cavity are estimated for the simplified geometry of hull bottom, and the non-dimensional parameters affecting air cavity phenomena are investigated. Extensive resistance tests for the model ship which has variation of step height and side strip have been performed to investigate the formation of air cavity and the drag reduction effectiveness. And also, the development of attached cavity to the bottom were observed from the flat bottom made by transparent acrylic plate. From this survey on the modification of bottom shape and the air lubrication technique, the total resistance of model ship could be reduced by about 25% at the design speed compared to the proto type hull form.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.46-51
• /
• 2016

The TMCP steel has expanded in the marine structure during manufacturing process because of its excellent weld-ability and impact toughness. In the case of merchant ships, coverage of TMCP steel has been used widely on over DH36 Classifications material. The line heating process is applied to the outer surface of the steel plate for the shipbuilding. In this study, We compared between TMCP and normalizing steel for shipbuilding by analyzing some basic data through performing the natural cooling after the line heating. The experimental results show the angular misalignment changes in line heating. Heated surface of normalizing steel material expanded to $-0.3^{\circ}$ and reduced to $+0.2^{\circ}$ after cooling. And during cooling at $194^{\circ}C$ for 1,500 seconds, Angular Misalignment began from - direction to + direction, passed the critical point to the default at 2,200 seconds and did not take place any more at $103^{\circ}C$ after the 2,700 seconds. Angular Misalignment results of TMCP steels and Normalizing steel material show same angular misalignment lasted 1,200 seconds, TMCP steel has given more expansion and contraction angle which is $0.2^{\circ}$ than that of the Normalizing steel. Length difference between expansion and contraction is about 0.3 mm.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.198-204
• /
• 2005

Fluosilicate salts based hydration heat reducer(SWP-HR), used in this study, is composed of fluosilicate salts, soluble silica, aromatic polymer condensate and nitrate salt based inorganic compound with latent heat property. Effects of SWP-HR addition on the hydration heat and anti-crack property of cement mortar were investigated. Adiabatic hydration temperature and drying shrinkage length of SWP-HR added cement mortar had a tendency to decrease compared to those of cement mortar without SWP-HR addition. Also, it was confirmed through crack pattern experiment of plate-form specimen for elucidating crack-reducing characteristic that anti-crack property of SWP-HR added cement mortar was improved.

• Journal of the Korean Chemical Society
• /
• v.36 no.3
• /
• pp.419-427
• /
• 1992

The performance of homemade thermal field-flow fractionation (ThFFF) and the optimization for separation are investigated in terms of retention parameters and selectivity using polystyrene standards. The ribbonlike channel was constructed by sandwiching two Mylar spacers between two highly polished copper bars which serve as channel walls. The hot bar was heated by two electrical cartridge heaters and the cold bar had holes through the entire length, allowing tap water as coolant to enter. It has been observed that the retention of polystyrenes increases as the temperature gradient increases. And the retention decreases as the cold wall temperature increases from 20 to $45^{\circ}C$. In comparison with size exclusion chromatography, ThFFF is more selective but has relatively low efficiency. It has been found that the plate height is proportional to the flow velocity and good estimates of polydispersities can be made directly from the ThFFF data.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.62-68
• /
• 1997

In the first part of the paper, the crack growth process in rolling contact fatigue has been investigated on ring type plate specimens, in which crack growth is two dimensional and cracks are observed on the side surface of the specimens. The results have shown that cracks are initated from the contact surface in tensile mode in the direction approximately normal to the contact surface and after some short length of growth, shear mode growth occurs from the tip of the crack and it grows until the separation of the surface layer, namely flakung type failure, occurs. In the second part, mode U fatigue crack growth tests have been made by using an apparatus designed based on the concept that the subsurface fatigue crack growth in rolling contact fatigue is the mode U fatigue crack growth under the stress state where the tensile mode growth is suppressed by compression stress. The rest results have shown that the mode U fatigue crack growth occurs if the superposed compression stress is enough to suppress the tensile mode growth.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.1
• /
• pp.10-17
• /
• 2008

The purpose of this thesis is to reduce of error for source location through acoustic emission(AE) signal, generated elastic wave from crack growth to leak for facility diagnosis. Especially, in order to overcome noise from original signal, this paper proposed enhancement of source location by using noise reduction based on wavelet transform. To evaluate actual performance in experiments, Pencil Lead Break is used crack signal source on the aluminum plate and drain valve of air compressor is used as substitute pressure vessel to generate leak signal. In signal processing, wavelet shrinkage and soft threshold are used to discriminate signal source and then source location techniques have been effectively used with group velocity using material property and time difference between sensor using cross correlation. Source location for crack and leak test have some difference, but the result show that improved 30% with a average length within 10.46mm in crack test and improved 2% compare with average filter in leak test when we applied wavelet transform.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.1
• /
• pp.271-280
• /
• 2011

This study intends to analytically evaluate the vibration serviceability of the bridges for each long-span type having the same span length and road width using the Meister vibration sensation curve. With MIDAS, a structural analysis program, bridges were modeled using the girders as the frame element and slabs as the plate element. The transient analysis was performed using the moving loads of the design vehicles. This study presents the analytical process of reviewing the vibration serviceability during the design of long-span bridges. It involves the comparison of the vibration serviceability of different bridge types by applying the lagging-behind and acceleration amplitude from transient analysis to Meister curve. The result confirms that the process is appropriate.