• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.40-47
• /
• 2015

In this study, temperature characteristics and fire damage form were analyzed to investigate flame spreading form and fire probability from ignition sources subject to drivit component materials which is finishing material in architecture. Ignition sources were limited to a gas torch and exterior panel board fire, and the size of the sample was manufacture in 30 cm length ${\times}$ 50 cm height ${\times}$ 5cm thickness size. Marble (inner wall) + 3 mm drivit (outer wall), marble (inner wall) + 4 mm plaster stone (outer wall), sandwich panel + 3 mm driver bit (outer wall), sandwich panel + 3 mm driver bit + insulation (outer wall), and gypsum board (inner wall) + 3 mm drivit (outer wall) were prepared for the sample. As result of the research for temperature characteristics, large temperature difference by each material was shown in $218^{\circ}C{\sim}995^{\circ}C$ at 30 seconds and $501^{\circ}C{\sim}1078^{\circ}C$ at 300 seconds. Especially when the inner wall was a plaster board, lowest temperature of $501^{\circ}C$ was shown at 300 seconds and marble inner wall showed the following lowest temperature of $900^{\circ}C$. Temperature rising over $1000^{\circ}C$ was shown in other materials. Regarding fire damage form, drivit or gypsum board outer wall parts exposed to fire showed combustion and carbonization to show calcination(breaking phenomenon) and influence of heat exposure was higher as calcination became more severe.

• Plant Resources
• /
• v.6 no.2
• /
• pp.120-128
• /
• 2003

The objectives of this study, an analysis of the variation for leaf and fruit characteristics among the selected ten populations of Sorbus commixta Hedl. could be used for the conservation of gene resources and could provide information to superior trees selection. The results obtained from this study can be summarized as follows; Approximately, the Mt. Sungin population at Ulleung island showed larger values in overall characteristics and populations. On the other hand, Mt. Halla population at Jeju island showed the smaller values of the overall characteristics and populations. ANOV A tests showed that there were statistically significant differences in all leaf characteristics among the populations as well as individual trees within populations. But, for fruit characteristics, differences were statistically significant only among the populations. Cluster analysis using single linkage method based on leaf and fruit characteristics showed that ten selected populations of S. commixta in Korea could be clustered into three groups. Group I is Mt. Sungin at Ulleung island, Group II is Mt. Halla at Jeju island, and Group III comprises Osan, Mt. Kaji, Mt. Duckyoo, Mt. Balwang, Mt. Sobaek, Mt. O-dae, Mt. Jiri, and Mt. Taebaek. The selection level based on major agronomic traits, which are the Number of Fruit per Fruiting Lateral(NFL) over 50, and Fruit Length(FL) and Width(FW) over 10 mm, and Weight of 100 Fruit(WFI00) over 66 g, was applied on 100 sample trees, and five trees were selected. The selection effects from selected trees in NFL, FL, FW, and WF100 were evaluated as 132%, 151 %, 142%, and 264% compared to the mean of those 100 sample trees, respectively. Especially, Ulleung 2 showed excellent values that NFL and WFI00 were 95, and 69 g, respectively, suggesting a promising new cultivar for larger fruit and high productivity.

• Transactions of Materials Processing
• /
• v.28 no.5
• /
• pp.257-265
• /
• 2019

Multi-axial forging (MAF), a severe plastic deformation technique, is known to be difficult to obtain materials with homogeneous microstructures. Recently, multi-axial diagonal forging (MADF) process has been developed to solve this problem. In this study, in order to compare the microstructural and mechanical homogeneities of the MAFed and MADFed samples, oxygen-free copper (OFC) cubes measuring 25 mm in length were deformed through MAF and MADF processes and the average grain size and hardness were measured at the edge, face, and center regions of the samples. In the MAFed samples, ultrafine grains were formed at the center region, but a considerable amount of coarse grains remain at the face region. Therefore, the MAFed samples showed a high inhomogeneity in regards to grain size and hardness. On the contrary, in the case of the MADFed sample, the grain sizes at the edge, face, and center regions were similar and the hardness in all the regions are almost similar. This indicates that the MADFed sample has a homogeneous microstructure and uniform mechanical properties, which can be attributed to the homogeneous distribution of the effective strain throughout the material. The results of this study suggests that the MADF is a suitable process in the fabrication of high-strength copper materials with a homogeneous and ultrafine grain structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and $N_2$ gas ambient annealing method at $950^{\circ}C$ for 10 min. The specific contact resistivity ( $\rho_{c}$ ), sheet resistance($R_s$), contact resistance($R_c$), transfer length($L_T$) were calculated from resistance($R_T$) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho_{c}=3.8{\times}10^{-5}\Omega cm^{3}$, $R_{c}=4.9{\Omega}$, $R_{T}=9.8{\Omega}$ and $L_{T}=15.5{\mu}m$, resulting average values of another sample were $\rho_{c}=2.29{\times}10^{-4}\Omega cm^{3}$, $R_{c}=12.9{\Omega}$ and $R_{T}=25.8{\Omega}$. The physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and N$_2$ gas ambient annealing method at 950$^{\circ}C$ for 10 min. The specific contact resistivity($\rho$$\sub$c/), sheet resistance(R$\sub$S/), contact resistance(R$\sub$S/), transfer length(LT) were calculated from resistance(R$\sub$T/) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho$$\sub$c/=3.8x10$\^$-5/ Ω$\textrm{cm}^2$ , R$\sub$c/=4.9Ω, R$\sub$T/=9.8Ω and L$\sub$T/=15.5$\mu\textrm{m}$, resulting average values of another sample were $\rho$$\sub$c/=2.29x10$\^$-4/ Ω$\textrm{cm}^2$ , R$\sub$c/=12.9Ω, R$\sub$T/=25.8Ω. The Physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.764-768
• /
• 2002

Characteristics of ohmic Co/Si/Co contacts to n-type 4H-SiC are investigated systematically. The ohmic contacts were formed by annealing Co/Si/Co sputtered sequentially. The annealings were performed at $800^{\circ}C$ using RTP in vacuum ambient and $Ar:H_2$(9:1) ambient, respectively. The specific contact resistivity$(\rho_c)$, sheet resistance$(R_s)$, contact resistance$(R_c)$, transfer length$(L_T)$ were calculated from resistance$(R_T)$ versus contact spacing(d) measurements obtained from TLM(transmission line method) structure. While the resulting measurement values of sample annealed at vacuum ambient were $\rho_c=1.0{\tiimes}10^{-5}{\Omega}cm^2$, $R_c=20{\Omega}$ and $L_T$ = 6.0 those of sample annealed at $Ar:H_2$(9:1) ambient were $\rho_c=4.0{\tiimes}10^{-6}{\Omega}cm^2$, $R_c=4.0{\Omega}$ and $L_T$ = 2.0. The physical properties of contacts were examined using XRD and AES. The results showed that cobalt silicide was formed on SiC and Co was migrated into SiC.

• KSBB Journal
• /
• v.14 no.3
• /
• pp.371-376
• /
• 1999

Simulation of preparative protein chromatography becomes necessary for separation as well as optimal operation. A mathematical model describing the behavior of elution peaks in preparative protein chromatography for single and binary component separation was solved numerically using a PDEsolver Macsyma$^{\circledR}$(Macsyma Inc., Arlington, MA, U.S.A.). Band profiles were calculated with the equilibrium-dispersive model of chromatography. The effects of the sample volume, concentrations of solutes in the sample, flow velocity and column length on the band profile of the elution peaks are discussed. The results in this paper suggest the model simulation for the binary mixture can be extended to multicomponent separations.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.33 no.4
• /
• pp.13-30
• /
• 2008

We explore the determinants of long-term relationship between the buyer and the supplier to help suppliers develope a strategy to build long-term relationship with their buyers. Based upon an extensive literature review, we propose three droops of independent variables which may affect long-term relationship, including (a) environmental factors (product complexity, product importance, source dependence, price sensitivity), (b) relational factors(trust, commitment, satisfaction, intention of expansion), (c) operational performance(quality, delivery, cost capability, technical knowhow). The buyer's actual period of relationship with its main supplier is used as a dependent variable. Using hierarchical multiple regression analysis, we empirically test hypotheses, analysing a sample of 290 manufacturing firms in the U.S. The statistical results indicate that the buyer's source dependence, price sensitivity and the supplier's commitment play a significant role in establishing long-term relationship between the buyer and the supplier. However, the supplier's cost capability and technical knowhow in operational performance negatively affect long-term relationship in contrast with our hypotheses. Due to this controversial result, we divide the sample group Into dual sourcing and multiple sourcing environments and reconduct regression analysis in a post hoc manner. The findings show that the supplier's cost capability and technical knowhow are negatively associated with the length of relationship only in the multiple sourcing environment. The results may confirm that both parties' opportunistic behavior is more salient in the multiple sourcing environment than in the single sourcing environment.

• The korean journal of orthodontics
• /
• v.34 no.3 s.104
• /
• pp.241-251
• /
• 2004

Previous studies have focused on the causes of root resorption after orthodontic treatment and treatment methods to reduce this phenomenon, and have been mainly associated with developed, mature roots. As parents become increasingly interested in their children's' dentition, orthodontists are performing fixed orthodontic treatment on patients of less than 10 years and before the completion of the immature root. Thus, the author evaluated the changes of root length and root form of maxillary immature incisors after orthodontic treatment, compared with those of mature teeth, and investigated the correlation according to gender, treatment duration, and displacement of incisors. The sample consisted of an immature root group of twenty-eight persons (between 8 and 10 years old) and a mature root group of thirty-one persons (between 11 and 15 years old). The crown and root length of the maxillary four incisors were measured with a periapical radiograph, changes in root length and crown-root ratio were calculated, and root form was classified according to a scoring system. The results were as follows. 1. The development of immature roots was not affected by orthodontic treatment and mostly showed normal root length and apical form. 2. Root length of immature teeth was sustained or became shorter, partially in long treatment duration or with open bite patients. Even though the teeth reached their normal root length, they demonstrated a blunt form. 3. Most of the mature roots showed mild resorption, and the form of mature roots was more blunt than the developed form of the immature roots (p<0.05). 4. The developed form of the immature roots was statistically related to treatment duration, while the form of the mature roots was significantly related to the displacement of incisors (p<0.05). 5. In contrast, other variables such as gender, classification of malocclusion, changes in overbite, and changes of U1 to SN showed no correlation with the root resorption of both groups.

• Imaging Science in Dentistry
• /
• v.51 no.1
• /
• pp.17-25
• /
• 2021

Purpose: This study was performed to investigate mandibular canal displacement in patients with ameloblastoma using a 3-dimensional mirrored-model analysis. Materials and Methods: The sample consisted of computed tomographic scans of patients with ameloblastoma (n=10) and healthy controls (n=20). The amount of mandibular canal asymmetry was recorded as a continuous variable, while the buccolingual (yaw) and supero-inferior (pitch) directions of displacement were classified as categorical variables. The t-test for independent samples and the Fisher exact test were used to compare groups in terms of differences between sides and the presence of asymmetric inclinations, respectively (P<0.05). Results: The length of the mandibular canal was similar on both sides in both groups. The ameloblastoma group presented more lateral (2.40±4.16 mm) and inferior (-1.97±1.92 mm) positions of the mental foramen, and a more buccal (1.09±2.75 mm) position of the middle canal point on the lesion side. Displacement of the mandibular canal tended to be found in the anterior region in patients with ameloblastoma, occurring toward the buccal and inferior directions in 60% and 70% of ameloblastoma patients, respectively. Conclusion: Mandibular canal displacement due to ameloblastoma could be detected by this superimposed mirrored method, and displacement was more prevalent toward the inferior and buccal directions. This displacement affected the mental foramen position, but did not lead to a change in the length of the mandibular canal. The control group presented no mandibular canal displacement.