• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.232-233
• /
• 2012

This paper presents an effective control scheme for an electric vehicle battery charger where a symmetrical bridgeless power factor-corrected converter and a buck converter are cascaded. Both converters have been popular in industries because of their high efficiency, low cost, and compact size, hence combining these converters makes the overall battery charging system strongly efficient. Moreover, this charger topology can operate at universal input voltage and attain a desired battery current and voltage without ripple. In order to achieve a unity input power factor and zero input current harmonic distortion, the proposed control scheme adopts duty ratio feed-forward control technique in both current and voltage control loop. Additionally, in the current loop, its reference is created by a phase-locked loop (PLL) block, leading to a pure sinusoidal input current although the input voltage waveform is being distorted. The feasibility and practical value of the proposed approach are verified by simulation and experiment with an 110V/60Hz ac line input and 1.5kW-72V dc output of the battery charging system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1579-1587
• /
• 2000

This paper presents the properties of the RF part in the receiving system based in IMT-2000 terminal technology. It mainly discuss the RF parameter performance of the receiving system for mobile telecommunication comparable to IS-98A and J-STD-018 specifications of commercially available CDMA and PCS, and is to anticipate the processing gain of the IMT-2000 receiving system, processing gain according to data processing rate, and terminal noise figure according to processing gain, relationship between noise figures according to Eb/Nt, Ioc. It is performed by such analysis method as CDMA and PCS receiving systems. Transmission bandwidth is n$\times$1.25 MHz(n=1, 3, 6, 9, 12) which is recommended by Qualcomm and NTT, the leading company in cdma 2000. Data transmission rate of IMT-2000 is classified into three cases as in moving vehicle environment of 144Kbps, outdoor pedestrian environment of 384Kbps, and indoor office environment of 2Mbps

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.1
• /
• pp.209-220
• /
• 2022

With the worldwide spread of African swine fever, interest in livestock epidemics has increased. Livestock transport vehicles are the main cause of the spread of livestock epidemics, but there are no empirical quarantine procedures and standards related to the mobility of livestock transport vehicles in South Korea. This study extracted the trajectory of livestock-related vehicles using the facility-visit history data from the Korea Animal Health Integrated System and the DTG (Digital Tachograph) data from the Korea Transportation Safety Authority. The results are presented as exposure indices aggregating the link-time occupancy of each vehicle. As a result, 274,519 livestock-related vehicle trajectories were extracted, and the exposure values by link and zone were derived quantitatively. This study highlights the need for prior monitoring of livestock transport vehicles and the establishment of post-disaster prevention policies.

• Journal of Korean Society of Transportation
• /
• v.25 no.3
• /
• pp.29-43
• /
• 2007

An automobile black box can provide sufficient and accurate information for investigating the causes of vehicle accidents as well as preventing them in the future. The database of accident information from stored data in the black box can provide a variety of services to the general public when it is accessed in a reasonable manner. minimizing intrusion into drivers' privacy. Therefore, the black box could become the main intelligent automobile Part, with extensive benefits for all associated industries as well as government agencies and insurance companies. While the introduction and spread of the black box are imminent in Korea, this paper reviews technology and product trends of the black box. In particular, this paper presents findings on the investigation of black box-related patent applications and an in-depth study of core patents from several leading counties, including the United States. In addition, this paper describes trends of standardization and legislation in leading countries and presents methods of standardization with suggestions for some development topics related to black box technology.

• Journal of Powder Materials
• /
• v.26 no.2
• /
• pp.146-155
• /
• 2019

Rare earth magnets are the strongest type of permanent magnets and are integral to the high tech industry, particularly in clean energies, such as electric vehicle motors and wind turbine generators. However, the cost of rare earth materials and the imbalance in supply and demand still remain big problems to solve for permanent magnet related industries. Thus, a magnet with abundant elements and moderate magnetic performance is required to replace rare-earth magnets. Recently, $a^{{\prime}{\prime}}-Fe_{16}N_2$ has attracted considerable attention as a promising candidate for next-generation non-rare-earth permanent magnets due to its gigantic magnetization (3.23 T). Also, metastable $a^{{\prime}{\prime}}-Fe_{16}N_2$ exhibits high tetragonality (c/a = 1.1) by interstitial introduction of N atoms, leading to a high magnetocrystalline anisotropy constant ($K_1=1.0MJ/m^3$). In addition, Fe has a large amount of reserves on the Earth compared to other magnetic materials, leading to low cost of raw materials and manufacturing for industrial production. In this paper, we review the synthetic methods of metastable $a^{{\prime}{\prime}}-Fe_{16}N_2$ with film, powder and bulk form and discuss the approaches to enhance magnetocrystalline anisotropy of $a^{{\prime}{\prime}}-Fe_{16}N_2$. Future research prospects are also offered with patent trends observed thus far.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.198-206
• /
• 2016

Fuel economy label will be used as a national indicator in energy management, leading to the development of car technology manufacturer and plays a role in providing consumer vehicle purchase information. But the government's fuel economy label is continued consumer complaint is different and diminishing fuel economy were introduced by the government to measure the exact fuel economy label than resetting the 5-cycle test method in the US for the domestic vehicle standards. Originally two test mode in order to reduce the impact of the sharp increase in the resources required but methods of calculating a measured result value by driving all of the five test mode a variety of environmental conditions and the running pattern is reflected to the fuel economy label (city( FTP-75 mode), highway(HWFET mode)) and using 5-cycle correction formula for calculating a fuel consumption value and the equivalent value to calculate the result of the 5-cycle test. The compensation was calculated expression 30s, 5-Cycle Test Method of vehicles in 2011 was considered necessary to review the existing 5-cycle correction formula for the New Type car due to the recent rapid development of automotive technology. In this study, recent technology is targeting 14 units New Type car applied over the same test method and the existing check test mode specific fuel economy properties and, as a result of analyzing the corrected expression differences that have already been developed with the existing test vehicle resulting large did not show the difference was found to correction formula also not getting the existing fuel correction expression significant effect on the improvement of the current automobile technology as a maximum error of less than 1.5%.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.7 s.112
• /
• pp.704-711
• /
• 2006

Vibration test on MAST(multi axial simulation table) system has several advantage over one-axial vibration test that could simulate 6-DOF, 3-axial translation and 3-axial moment, at the same time. Since field vibration motion can be fully represented with 6-DOF, multi-axial vibration test on vehicle component is widely conducted in technical leading companies to make sure its fatigue performance in vibration environment. On the way to fulfill the process, editing technique of obtained field data is key issue to success a reliable vibration testing with MAST system. Since the original signals are not only too large to fulfill it directly, but all of the measured data is not guarantee its convergency on generating its driving files, editing technique of the original signals are highly required to make some events that should meet the equal fatigue damage on the target component In this paper, key technique on editing a field data feasible for MAST system is described based on energy method in vibration fatigue. To explain its technique explicitly, author first introduced a process on field data acquisition of two vehicle component and then, representing events are produced to keep up with the editing strategy about a energy method. In the final chapter, a time information regarding a vibration test on MAST system is derived from the energy data which is critical information to perform a vibration test.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.6
• /
• pp.649-656
• /
• 2017

At present, hydrogen is emerging as a future energy source based on environment-friendly aspect, creation of new industry, and enhancement of domestic energy security. In accordance with it, the world's leading automobile companies are focusing on the development and commercialization of hydrogen electric vehicle technology, and each country is strengthening its hydrogen fueling station deployment strategy for its own country. Furthermore, the supply of hydrogen fueling stations is actively promoting under national support. More than 500 hydrogen fueling stations are being constructed, operated and planned around the world. The introduction of hydrogen energy is also progressing in Korea, by announcing road-map to supply hydrogen electric vehicles and hydrogen fueling stations by year. However, there is insufficient discussion on the capacity of hydrogen fueling station in Korea. Therefore, this study suggests the optimum capacity of hydrogen fuelling station for domestic hydrogen economy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.764-769
• /
• 2006

Vibration test on MAST(multi axial simulation table) system has several advantage over one-axial vibration test that could simulate 6-DOF, 3-axial translation and 3-axial moment, at the same time. Since field vibration motion can be fully represented with 6-DOF, multi-axial vibration test on vehicle component is widely conducted in technical leading companies to make sure its fatigue performance in vibration environment. On the way to fulfill the process, editing technique of obtained field data is key issue to success a reliable vibration testing with MAST system. Since the original signals are not only too large to fulfill it directly, but all of the measured data is not guarantee its convergency on generating its driving files, editing technique of the original signals are highly required to make some events that should meet the equal fatigue damage on the target component In this paper, key technique on editing a field data feasible for MAST system is described based on energy method in vibration fatigue. To explain its technique explicitly, author first introduced a process on field data acquisition of two vehicle component and then, representing events are produced to keep up with the editing strategy about a energy method. In the final chapter, a time information regarding a vibration test on MAST system is derived from the energy data which is critical information to perform a vibration test.

• Journal of Korean Society of Transportation
• /
• v.26 no.4
• /
• pp.123-133
• /
• 2008

Information collection systems and applications in a ubiquitous environment has emerged as a leading issue in transportation and logistics. A productive application example is a traffic information collection system based on probe vehicles and wireless communication technology. Estimation of hourly OD pairs using probe OD data is a possible target. Since probe OD data consists of sample OD pairs, which vary over time and space, computation of sample rates of OD pairs and expansion of sample OD pairs into static OD pairs is required. In this paper, the authors proposed a method to estimate sample OD data with probe data in Jeju City and expand those into static OD data. Mean absolute percentage difference (MAPD) error between observed traffic volume and assigned traffic volume was about 22.9%. After removing abnormal data, MAPD error improved to 17.6%. Development of static OD estimation methods using probe vehicle data in a real environment is considered the main contribution of this paper.