• Design & Manufacturing
• /
• v.12 no.3
• /
• pp.55-59
• /
• 2018

In a multi-cavity mold having a runner layout of a fish bone structure, problems of unbalanced filling between cavities occur constantly. Unbalanced charging lowers the dimensional accuracy of a molded article and causes deformation after molding. To solve this problem, the gate size connected to each cavity is adjusted using the BGV (Balanced Gate Value) equation. In this paper, in order to solve the filling imbalance problem of the runner layout mold of fish bone structure through injection molding analysis study, we compared the charging imbalance phenomenon before and after improvement after adjusting the gate size by applying BGV equation. From the results of the molding analysis, the shrinkage ratio before and after the improvement of the molded article was improved by only about 0.08%. Based on these results, it was confirmed that the charging imbalance problem was not significantly improved even when the BGV equation was applied.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.5
• /
• pp.169-179
• /
• 2019

During the initial design stage of apartment complex, the photovoltaic(PV) system has been considered as an alternative of renewable energy system and planned to install at the rooftop floor level in general. The electric power generation characteristics can be influenced by the block layout, building orientation and roof top structure because of azimuth angle, tilt angle, and partial shading. This study aims to investigate power generation characteristics of photovoltaic system in apartment buildings by considering the partial shading conditions due to the block layout, building orientation and roof-top structures. For the photovoltaic module arrangement planning in rooftop floor level, shading areas were firstly analyzed due to the adjacent building structure. And the annual and seasonal power generation of PV system were analyzed through the PVsyst simulation results. The results show that shading period at the roof top surface can be increased due to the parapet and water tank. Initial design power capacity can be decreased by considering the daily insolation period and distance between PV modules through the shading simulation. As the number of PV modules decreases, the annual power generation can be decreased. However annual power generation per unit area of PV modules can be increased and performance ratio can be increased above 80%. Also the power generation of PV system can be critically affected by building orientation and the performance ratio can be drastically decreased in east-oriented buildings due to the shading problems caused by adjacent structures at roof top level such as parapet and water tank.

• The Research Journal of the Costume Culture
• /
• v.18 no.2
• /
• pp.261-276
• /
• 2010

The analysis of an art trend in the principle dimension starts by observing the object of work in the perspective of formative composition and recognizing it as a universal system. It can be said that it is consistent with an interpretation method for a form theory of formal history by Heinrich W$\ddot{o}$lfflin, a leading form critic in art criticism. Hence, the purpose of this study was to find out what are the formative principles in Renaissance Classicism as a design principle to be applicable to modern fashion by reviewing the formative characteristics of Renaissance Classicism Architecture with which W$\ddot{o}$lfflin directly dealt. As for the theoretical literature review, I used W$\ddot{o}$lfflin's theoretical framework and looked at the Renaissance Classicism Architecture that he studied and examined the possibility of utilizing his theory as a layout principle and the characteristics. As for analysis of design cases, I applied the aforementioned architecture layout principle to modern fashion and conducted case study analysis to delve into distinctive layout principles found in fashion. The study showed that the Renaissance Classicism Architectural Style is marked by linearity, planarity, closing and multiple unity: linearity was expressed in the observation form in fixed frontal view and an emphasis on a tangible silhouette homeogenous and definite line structures; planarity was achieved in the form of paralleled layers of frontal view element, planarity style, and identical and proportional repetition of various sizes.; closing signified the pursuit of complete and clear regularity, and architecture developed in a constructive phase through organizational inevitability and absolute invariability.; multiple unity was expressed in self-completedness and independent parallel of discrete forms and harmony of emphasized individual elements in a totality. Applying these layout characteristics of the Renaissance Classicism Architectural style and to see their individual expressive features, I found out that in adopting layout principles of the Renaissance Classicism Architecture to modern fashion, it turned out to be an emphasis of individual silhouettes, a flattened space, completed objects, organic harmony among independent parts: the emphasis of individual silhouettes was expressed in individual definitiveness of formative lines of clothes in accordance with body joints and an emphasis on formative lines of clothes; the flattened space was marked by single layer structure, planarity of elements of clothes, and listing arrangement by appropriate proportion.; the completedness of the objects was expressed by the stationary state where overall image is fixed, the construction of homogeneous and complete space, and absolute inevitability of internal layout in proportion; lastly, organic harmony of independent parts was stressed in independent completedness of each detail, and organic harmony of the whole. The expressive features would lead to a unique expression style of linear emphasis, proportion, constructive forms, and two-dimensional arrangement. The meaning of this study is follows: The characteristics of art school of thought are given shape by appling & analysing the architectural layout principles of historical art school of thought to modern fashion in the view point of formal construction dimension. The applied possibility of historical art school of thought as the source of inspiration about the fashion design is extended.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1619-1626
• /
• 2017

Electronic components that are used in high-level radiation environment require a semiconductor device having a radiation-hardened characteristic. In this paper, we proposed a radiation-hardened I-gate n-MOSFET (n-type Metal Oxide Semiconductors Field Effect Transistors) using a layout modification technique only. The proposed I-gate n-MOSFET structure is modified as an I-shaped gate poly in order to mitigate a radiation-induced leakage current in the standard n-MOSFET structure. For verification of its radiation-hardened characteristic, the M&S (Modeling and Simulation) of the 3D (3-Dimension) structure is performed by TCAD (Technology Computer Aided Design) tool. In addition, we carried out an evaluation test using a $Co^{60}$ gamma-ray source of 10kGy(Si)/h. As a result, we have confirmed the radiation-hardened level up to a total ionizing dose of 20kGy(Si).

• Steel and Composite Structures
• /
• v.26 no.6
• /
• pp.759-769
• /
• 2018

This paper studies shear and tensile behaviors of headed stud connectors in double skin composite (DSC) structure. Firstly, 11 push-out tests and 11 tensile tests were performed to investigate the ultimate shear and tensile behaviors of headed stud in DSC shear wall, respectively. The main parameters investigated in this test program were height and layout of headed stud connectors. The test results reported the representative failure modes of headed studs in DSC structures subjected to shear and tension. The shear-slip and tension-elongation behaviors of headed studs in DSC structures were also reported. Influences of different parameters on these shear-slip and tension-elongation behaviors of headed studs were discussed and analyzed. Analytical models were also developed to predict the ultimate shear and tensile resistances of headed stud connectors in DSC shear walls. The developed analytical model incorporated the influence of the dense layout of headed studs in DSC shear walls. The validations of analytical predictions against 22 test results confirmed the accuracy of developed analytical models.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.10a
• /
• pp.315-321
• /
• 1996

The structural topology optimization presented in this paper is based on an evolutionary procedure, developed by Xie and Steven, in which the low stressed material of a structure is removed from the structure step-by-step until an optimal design is obtained. By appling this procedure a layout or topology of a structure can be found from a initial block of material. The purpose of this paper is to implement the evolutionary procedure, introduce some novel features and investigate its feasibility by studying a few examples.

• Transactions of Materials Processing
• /
• v.23 no.8
• /
• pp.501-506
• /
• 2014

Progressive shearing with blanking dies is commonly employed to produce large quantities of tiny sheet metal electronic parts. Sheet metal pins, which are narrow and long, that are sheared with a progressive die set are often twisted. The twist in the sheet metal pins, which usually occurs in the final shearing operation, generally decreases with increasing blank holding force. The blank holding forces in all shearing operations are not the same because of different shearing positions and areas. In the current study, the optimal layout of the springs in a progressive die set to minimize the twist of the sheet metal pin is proposed. In order to find the holding force acting on the tiny narrow blanks produced with the proposed springs during the shearing process, the equivalent area method is used in the structural analysis. The shearing of the sheet-metal pin was simulated to compute the twist angle associated with the blank holding force. The constraint condition satisfying the pre-set blank holding force from the previous shearing operations was imposed. A design of experiments (DOE) was numerically implemented by analyzing the progressive die structure and by simulating the shearing process. From the meta-model created from the experimental results and by using a quadratic response surface method (PQRSM), the optimal layout of the springs was determined. The twist of sheet metal pin associated with the optimal layout of the springs found in the current study was compared with that of an existing progressive die to obtain a minimal amount of twist.

• Journal of architectural history
• /
• v.18 no.5
• /
• pp.81-100
• /
• 2009

The study on Buddhism architecture in early Joseon dynasty was inactive. The period of King Sejo is important for studying the trend of Buddhism architecture in early Joseon, that was transmitted from the end of Goryeo dynasty, but it was difficult to know its exact situation due to lack of related records. The records were all written by Kim Su-ohn, which are Wongaksabi' 'Sangwonsajungchanggi' 'Bongseonsagi 'Geonginsajungchanggi'. The main hall was mainly second floor and there were necessarily annexed buildings at the right and left of the main hall. So the plane figure of $\Box\Box\Box$ was shown. It was a main stream for main hall. This layout may be referred to search for the origin of the layout in courtyard based structure(中庭形) in the late Joseon dynasty. Most of temples had 3 gates. Some part of horizontal corridor was used as 2 gates and the outer gate, far from main hall, was without corridor. The gate leading to front yard of main hall was called front gate, the next middle gate and the outer gate was Oisamun(外沙門) or Samun(沙門). Im most of the temples, people could enter into the front yard through pavilion which had the function of bell tower. The pavilions were located between front gate and first corridor. It is thought that this layout of the place for making bean curd outside the temple area will contribute to different studies on temples making bean cure in the future. The records about temples's foundation studied above are a little different between temples, but have more similarities. There common denominators represent the architecture tendency of Buddhist temples in the related period. It is thought that such a tendency was also shown on architecture of other temples during the reign of King Sejo as well as Buddhist temples.

• Knowledge Management Research
• /
• v.23 no.2
• /
• pp.193-210
• /
• 2022

The rapid development of mobile technology and the improvement of network speed are providing convenience to various services, and mobile shopping malls are no exception. Although efforts are being made to promote sales by combining various technologies such as customized recommendations using big data and specialized personalization services based on artificial intelligence, most mobile shopping malls have the same detailed page information structure including detailed product information. In this context, in this study, it was determined that the content layout of the product detail page and the mobile product detail page layout tailored to the consumer's preference should be presented according to the consumer's preference. Based on Higgins' Regulatory Focus Theory, a study of consumer propensity revealed that the content layout arrangement on a product detail page, when presented in an F-shape, informs the consumer that it is organized. If presented in a Z-shape, vivid information was recognized, and it was examined whether the product attitude and purchase intention were affected. As a result, when the content layout composition was presented as a layout arrangement in the form of a sense of unity and organization, prevention-focused consumers were positively affected by product attitudes and purchase intentions, and promotion-oriented consumers felt freedom. When presented in an arrangement, it was confirmed that the product attitude and purchase intention were affected.

• The Journal of the Korea Contents Association
• /
• v.10 no.10
• /
• pp.111-119
• /
• 2010

This paper deals with the experiments of optokinetic differentiation within eye tracking test through the menu direction and cognitive degree of service menu title for watching digital media service. Researcher establish a research topic which verification of differentiations of eye tracking velocity when media user perceive the service menu title within vertical structure or horizontal structure. Experimentation was designed with two types of menu structure-vertical or horizontal-and these have each 9 cases of eye tracking tasks for experimentee. Researcher arrives at a conclusion through as stated above experiment that cases of vertical menu structure is more effective method with linear channel service menu, otherwise that cases of horizontal menu structure is more effective method with non linear channel service menu, like a video on demand service. The research results will be very helpful with actual media industry players when they planning the evolutionary direction of their menu layout.