• JSTS:Journal of Semiconductor Technology and Science
• /
• 제5권2호
• /
• pp.83-88
• /
• 2005

The interface-states between the top silicon layer and buried oxide layer of nano-SOI substrate were developed. Also, the effects of thermal treatment processes on the interface-state distributions were investigated for the first time by using pseudo-MOSFETs. We found that the interface-state distributions were strongly influenced by the thermal treatment processes. The interface-states were generated by the rapid thermal annealing (RTA) process. Increasing the RTA temperature over $800^{\circ}C$, the interface-state density considerably increased. Especially, a peak of interface-states distribution that contributes a hump phenomenon of subthreshold curve in the inversion mode operation of pseudo-MOSFETs was observed at the conduction band side of the energy gap, hut it was not observed in the accumulation mode operation. On the other hand, the increased interface-state density by the RTA process was effectively reduced by the relatively low temperature annealing process in a conventional thermal annealing (CTA) process.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.66-75
• /
• 1997

This study was undertaken to investigate tribology characteristics of the alumina ceramics($Al_2O_3$) of the various purity for the variation of ambient condition such as air and vacuum. The wear test was carried out under different experimental condition using the wear test device, which was designed for this study, and in which the annular surface of wear testing specimens as well as mate specimen made of STB2 steel, were subjected to sliding speed, applied load and the sliding distance. The results obtained were as follows. As the ambient pressure decreases, the friction coefficient increases because the protective layer made of absorption due to decrease of the amount of ambient gas can not be formed. As the friction coefficient paticularly for 85% alumina lower than 95% and 99.7% in the alumina purity increases by an influence of heat accumulation caused by small elastic modulus and thermal conductivity. The friction surface of ceramics can be protected in the air by the influence of the oxides transfered from STB2. However, in the vacuum, the protective layer made of the absorption substance can not be formed due to the decrease of ambient gas.

• Journal of information and communication convergence engineering
• /
• 제13권4호
• /
• pp.257-263
• /
• 2015

In this study, organic field-effect transistors (OFETs) using a copper phthalocyanine (CuPc) material as an active layer and SiO₂ as a gate insulator were fabricated with varying active layer thicknesses and channel lengths. Further, using a thermal evaporation method in a high-vacuum system, we fabricated a CuPc FET device of the top-contact type and used Au materials for the source and drain electrodes. In order to discuss the channel formation and FET characteristics, we observed the typical current-voltage characteristics and calculated the threshold voltage of the CuPc FET device. We also found that the capacitance reached approximately 97 pF at a negative applied voltage and increased upon the accumulation of carriers at the interface of the metal and the CuPc material. We observed the typical behavior of a FET when used as an n-channel FET. Moreover, we calculated the threshold voltage to be about 15-20 V at V_DS = -80 V.

• KSBB Journal
• /
• 제15권5호
• /
• pp.514-520
• /
• 2000

Simultaneous nitrification and denitrification of ammonia and organic compounds-containing wastewater were performed in a fluidized bed biofilm reactor with polysulfone(PS) hollow fiber as a double layer biomass carrier. The PS hollow fiber fragment has both aerobic and anoxic environments for the nitrifiaction and denitrification at the shell and lumen-side respectively. The reactor system showed about 80% nitrification efficiency stably throughout the ammonia load conditions applied in the experiment. Denitrification efficiency depended on organic load and C/N ratio. High free ammonia concentration and low dissolved oxygen resulted in nitrite accumulation which leads to enhance organic carbon efficiency in denitrification when compared to nitrate denitrification. The simultaneous nitrification and denitrification reactor system has an economic advantages in reduced chemical cost of organic carbon for denitrification as well as compact reactor configuration.

• 한국진공학회지
• /
• 제4권S2호
• /
• pp.156-162
• /
• 1995

For a stimulating neural electrode, the charge density should be as large as possible to provide adequate stimulation of the nervous system while allowing for miniaturization of the electrode. Since iridium oxide is able to produce high charge densities while preventing undesirable reactions due to charge storage, it has become a promising material for neural prostheses. Successful production of stable Ir and Ir oxide films on various substrates now limits the use of this material. Ir was deposited on two differently prepared surface of (mirror finish, passivation) surgical Ti-6AI-4V with several methods. Ion beam mixing of sputter deposited Ir films on passivated Ti-6AI-4V produced stable and good adherent Ir films. It was found that the increase in charge density of pure Ir on continuous cyclingis due to the accumulation of the oxide phase ( associated with a large surface area) in which the valence state of iridium changes and the double-layer capacitance increases. This study also showed that the double layer capacitance is equally or even more responsible for the high charge density of anodically formed Ir oxide.

• 한국환경복원기술학회지
• /
• 제9권5호
• /
• pp.50-59
• /
• 2006

This study was initiated to investigate soil chemical properties under different soil systems. Data such as soil acidity(pH), electrical conductivity(EC), organic matter content(OMC), and cation exchange capacity(CEC) were analyzed with samples from multi-layer, USGA, and mono-layer systems. N, P, K and micronutrients were also measured. Multi-layer system was built up to 60-cm depth with rootzone layer, intermediate layer and two drainage layers. USGA system 45 centimeters deep was constructed with rootzone layer, intermediate layer and drainage layer. Mono-layer system, however, was made only with a 30-cm rootzone layer. Differences were observed in soil pH, EC, OMC, CEC and micronutrients. Soil pH was acceptable for turfgrass growth a year after establishment, being 5.5 to 6.5 in the study. Differences were greatly observed for EC among soil systems. Values of EC for multi-layer, USGA, and mono-layer systems were 39.79, 31.26 and 103.54 uS/em, respectively. The increase rate was approximately 4 to 8 times greater with mono-layer system than those with other two systems. Therefore, it was necessary to avoid micronutrient deficiency such as Fe, Mn etc. through an effective management program in mono-layer system because of its faster potential feasibility of salt accumulation. The greatest OMC was associated with USGA system, being 0.97% which was 11% over that of the other systems. Slight differences were observed for CEC among them. Mono-layer system produced 1.45 me/100g, 10.3% and 8.9% lower in CEC than those of multi-layer and USGA system, respectively. Micronutrients such as Fe, Zn, and Mn etc. were below the level required for turf growth, regardless of soil systems. It was considered that one year after turf establishment was not enough to build up micronutrients in sand-based soil systems to the normal level for a turf growth. These results demonstrate that intensive management program including grow-in concept fertilization should be integrated into sand-based soil systems, even after a year in establishment. Regular nutrient monitoring by soil analyses is a strong necessity to decide the kinds and amount of fertilizer. Also, strategic management program must be selectively employed according to sports turf soil systems.

• 대한기계학회논문집
• /
• 제16권5호
• /
• pp.838-848
• /
• 1992

본 연구에서는 김성호등의 형상모델인 Fig.1(b)에서 전단하중이 작용하는 경 우에 대한, 복합재료의 탄성층 내부(레진층)에 존재하는 중앙균열의 응력확대계수 산 출을 위하여 균열부위를 제외하고는 섬유층과 레진층이 완전히 접착되었다고 가정한 모델을 다음과 같이 설정 하였다. 접착레진을 주로하는 탄성층(resin rich layer)을 중심으로 상하 각1개의 섬유층(fiber rich layer)과 균질한 특성을 갖는 복합재료의 층으로 단순화하였으며, 복합재료는 레진층이나 섬유층에 비하여 무한히 두꺼우므로 반무한체로 이상화 하였다. 선형탄 이론에 의한 혼합경계조건문제(mixed boundary value problem)로 부터 제2종 Fredholm 적분방정식(fredholm integral equation of a second kind)을 유도하였으며 수치해석적인 방법에 의하여 응력확대계수를 구하였다. 또한, 복합재료의 재료물성 및 균열길이, 섬유두께등이 기하학적 변수에 대하여 응력 확대계수를 산출하였다.

• 한국정보통신학회논문지
• /
• 제25권9호
• /
• pp.1158-1165
• /
• 2021

본 논문은 메모리의 사이즈를 줄이기 위해 Pooling Layer가 MAC에 통합된 구조의 최적화된 CNN가속기를 설계하는 것을 제안한다. 메모리와 데이터 전달 회로의 최소화를 위해 MNIST를 이용하여 학습된 32bit 부동소수점 가중치 값을 8bit로 양자화하여 사용하였다. 가속기칩 크기의 최소화를 위해 MNIST용 CNN 모델을 1개의 Convolutional layer, 4*4 Max Pooling, 두 개의 Fully connected layer로 축소하였고 모든 연산에는근사화 덧셈기와 곱셈기가 들어간 특수 MAC을 사용한다. Convolution 연산과 동시에 Pooling이 동작하도록 설계하여 내장 메모리를 94% 만큼 축소하였으며, pooling 연산의 지연 시간을 단축했다. 제안된 구조로 MNIST CNN 가속기칩을 TSMC 65nm GP 공정으로 설계한 결과 기존 연구결과의 절반 크기인 0.8mm x 0.9mm = 0.72mm²의 초소형 가속기 설계 결과를 도출하였다. 제안된 CNN 가속기칩의 테스트 결과 94%의 높은 정확도를 확인하였으며, 100MHz 클럭 사용시 MNIST 이미지당 77us의 빠른 처리 시간을 획득하였다.

• 한국미생물·생명공학회지
• /
• 제1권1호
• /
• pp.13-18
• /
• 1973

Bacillus subtilis의 생균 및 포자액을 자외선 조사와 diethylsulfate 처리로서 adenine 요구변이주 총 62주를 분리하였다. 이들 변이주는 발효배지에 자외선흡수 물질을 축적하고 있음을 확인하였으며 이 축적물은 thin-layer chromatogram 자외선흡수 곡선등으로 hypozanthine, uracil 임을 동정하였다. 이 중에서 hypoxanthine만을 축적하는 변이주 BS-137의 배지성분을 검토한 결과 탄소원소로서는 glucose가 좋았으며 질소원으로서는 yeastext와 NaNO$_3$ 가 적당하였다. 아울러 배양액으로부터 hypoxanthine을 분리 정제하는 방법을 확립하였다.

• 상하수도학회지
• /
• 제35권3호
• /
• pp.197-204
• /
• 2021

In MBR, extracellular polymeric substance (EPS) is known as an important factor of fouling; soluble EPS (sEPS) affects internal contamination of membrane, and bound EPS (bEPS) affects the formation of the cake layer. The production of EPS changes according to the composition of influent, which affects fouling characteristics. Therefore, in this study, the effects of the F/M ratio on the sEPS concentration, bEPS content, and fouling were evaluated. The effects of F/M ratio on the amount and composition of EPS were confirmed by setting conditions that were very low or higher than the general F/M ratio of MBR, and the fouling occurrence characteristics were evaluated by filtration resistance distribution. As a result, it was found that the sEPS increased significantly with the increase of the F/M ratio. When the substrate was depleted, bEPS content decreased because bEPS was hydrolyzed into BAP and seemed to be used as a substrate. In contrast, when the substrate is sufficient, UAP (utilization-associated products) was rapidly generated in proportion with the consumption of the substrate. UAP has a relatively higher Protein/Carbohydrate ratio (P/C ratio) than BAP, and this means, it has a higher adhesive force to the membrane surface. As a result, UAP seems like causing fouling rather than BAP (biomass-associated products). Therefore, R_f (Resistance of internal contamination) increased rapidly with the increase of UAP, and R_c (Resistance of cake layer) increased with the accumulation of bEPS in proportion, and as a result, the fouling interval was shortened. According to this study, a high F/M ratio leads to an increment in UAP generation and accumulation of bEPS, and by these UAP and bEPS, membrane fouling is promoted.