• 대한기계학회논문집
• /
• 제19권12호
• /
• pp.3317-3328
• /
• 1995

The objective of the present study is to predict the characteristics of heat and mass transfer around an evaporative condenser. Numerical calculations have been performed using multi-zone method to investigate heat transfer rate and evaporation rate with the variation of inlet condition(velocity, relative humidity and temperature) of the moist air, the flow rate of the cooling water and the shape of the condenser tube. From the results it is found that the profile of heat flux is the same as that of evaporation rate since heat transfer along the gas-liquid interface is dominated by the transport of latent heat in association with the vaporization(evaporation) of the liquid film. The evaporation rate and heat transfer rate is increased as mass flow rate increases or relative humidity and temperature decrease respectively. But the flow rate of the cooling water hardly affect the evaporation rate and heat flux along the gas-liquid interface. The elliptic tube which the ratio of semi-minor axis to semi-major axis is 0.8 is more effective than the circular tube because the pressure drop is decreased. But the evaporation rate and heat flux shown independency on the tube shape.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권7호
• /
• pp.351-363
• /
• 2001

This paper presents an experimental investigation on the heat trensfer characteristic of micro pipe (MHP) array with 38 triangular microgrooves. A heat pipe is an effective heat exchanger operating without external power. The heat pipe transfers heat by means of the latent heat of vaporization and two-phase fluid flow driven by the capillary force. The overall size of the MHP array can be put undermeath a microelectonic die and integrated into the electrronic package of a microelectronin device to dissipate the heat from the die. The MHP array is fabricated by micromachining with a silicon wafer and a glass substrate. The MHP was filled with water and sealed. The experimental results show the temperature decrease of 12.1$^{\circ}C$ at the evaporator section for the input power of 5.9 W and the improvement of 28% in the heat transfer rate.

• 동력기계공학회지
• /
• 제22권1호
• /
• pp.48-55
• /
• 2018

It has recently been reported that methanol fuel has been used in the product carrier with established duel fuel engine, which has been greatly reducing emissions of $CO_2$, NOx and SOx from the engine. However, to use methanol alone as fuel oil in a general diesel engine, design modification of cylinder head is needed because the ignition aid device or the duel fuel injection system is needed. On the other hand, only if the mixer is installed on the fuel oil supply line, diesel oil - methanol blending oil can be used as fuel oil for the diesel engine, but there is a problem of the phase separation when two fuels are mixed. In this study, diesel oil and methanol were blended compulsorily in preventing the phase separation with installing agitators and a fuel oil boost pump on fuel line of a test engine. Also, cylinder pressure and fuel consumption quantity were measured according to engine load and methanol blending ratio, and indicated mean effective pressure, heat release rate and combustion temperature obtained from the single zone combustion model were analyzed to investigate the effects of latent heat of vaporization of methanol on combustion stability and characteristics. As a result, the combustion stability and characteristics of 10% methanol blending oil are closest to the those of diesel oil, and it could be used as fuel oil in existing diesel engines without deterioration of engine performance and combustion characteristics.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1122-1127
• /
• 2004

an isolated droplet combustion exposed to pressure perturbations in stagnant gaseous environment is numerically conducted. Governing equations are solved for flow parameters at gas and liquid phases separately and thermodynamic parameters at the interfacial boundary are matched for problem closure. For high-pressure effects, vapor-liquid interfacial thermodynamics is rigorously treated. A series of parametric calculations in terms of mean pressure level and wave frequencies are carried out employing a n-pentane droplet in stagnant gaseous air. Results show that the operating pressure and driving frequency have an important role in determining the amplitude and phase lag of a combustion response. Mass evaporation rate responding to pressure waves is amplified with increase in pressure due to substantial reduction in latent heat of vaporization. Phase difference between pressure and evaporation rate decreases due to the reduced thermal inertia at high pressure. In addition to this, augmentation of perturbation frequency also enhances amplification of vaporization rate because the time period for the pressure oscillation is much smaller than the liquid thermal inertia time. The phase of evaporation rate shifts backward due to the elevated thermal inertia at high acoustic frequency.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1766-1775
• /
• 2001

A theoretical analysis on the heat and mass transfer in an evaporative cooler is presented in this work. The evaporative cooler is modeled as a channel filled with porous media the interstitial surface of which is covered by thin water film. Assuming that the Lewis number is unity and the water vapor saturation curve is linear, exact solutions to the energy and vapor concentration equations are obtained. Based on the exact solutions, the characteristics of the heat and mass transfer in the evaporative cooler are investigated. The comparison of the cooling performance between the evaporative cooler and the usual sensible heat exchanger is also carried out. Obviously, the evaporative heat exchanger shows better cooling performance than the sensible heat exchanger. This is due to the latent heat of water vaporization, which results in apparent increases both in the interstitial heat transfer coefficient and the specific heat of the air stream in the evaporative cooler.

• 대한기계학회논문집B
• /
• 제33권10호
• /
• pp.737-747
• /
• 2009

This study is to investigate the effect of the moisture, volatile matter and particle size in the coal on the pulverized coal combustion characteristics using CFD. The results show that as the moisture content in coal increases, flame temperature decreases because of heat loss driven from latent heat of vaporization and reduction of heating value. As the volatile matter content in the coal increases, the temperature in the region near the burner increases, while the temperature in rear region of boiler decreases. The solution to keep the temperature in the rear region of boiler is suggested that particle size is needed to be larger. As the particle size increases, the temperature in the rear region of boiler show tendency to increase, for combustion burning time of coal could be extended.

• 한국농공학회지
• /
• 제32권E호
• /
• pp.88-94
• /
• 1990

Several models physically based to predict the evolution of the snowpack have been proposed. Validity of these models for hourly estimation is, however, questionable, since they have been tested only on a daily basis. A computational model to predict the amount of snowpack on an hourly basis in terms of snowload from a set of meterological measurements was developed and investigated the rapid snowmelt conditions during Fohn events in the Takada plain.

• 한국추진공학회지
• /
• 제14권2호
• /
• pp.46-53
• /
• 2010

본 연구에서는 하이브리드 추진 연소에서 산화제의 상(Phase)에 따른 연소특성 변화를 연구하였다. 산화제는 $GN_2O$와 $LN_2O$를 사용하고 고체연료는 HDPE(High Density PolyEthlene)를 적용하여 연소실험을 수행하였고, 상에 따른 고체연료의 후퇴율과 압력선도, 연소효율의 변화 등을 조사하였다. $LN_2O$를 적용할 경우 액체 산화제의 기화에 필요한 잠열이 화염에서 발생되는 연소에너지에 비해 무시할 정도로 작아 $GN_2O$를 산화제로 사용했을 때의 고체연료 후퇴율과는 큰 차이가 없었지만, 추진 성능효율이 낮아짐을 확인하였고, 액체 산화제의 유량이 증가할수록 산화제의 기화에 필요한 열전달 증가로 인 해 연소 불안정성이 커짐을 확인하였다.

• 오토저널
• /
• 제14권3호
• /
• pp.71-79
• /
• 1992

Recently, air pollution and energy security problems have necessitated the development of alternative fuel vehicles. As an alternative fuel vehicle FFV(Flexible Fuel Vehicle) which can be operated by and mixture between gasoline and M85(methanol 85% and gasoline 15% by vol. percent) has been drawing great attention. But poor cold startability of high methanol- content fuel which is characteristic of lower fuel volatility and higher latent heat of vaporization than gasoline is one of the major problems to be solved for the development of FFV. In this paper, important factors influencing cold startability of general S.I. engines are described. And, so-me cost-effective and practical methods were investigated in view of the optimization of fuel-ing parameters and ignition system for M85 fuel. The test results showed good startability up to (-22)-(-23).deg.C.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.472-475
• /
• 2010

나노 알루미늄과 물의 연소 반응을 정상상태 층류 연소로 모델링하여 이론적 접근을 하였으며 압력에 따른 화염전파속도의 영향을 조사하였다. 물의 상변화에 따른 증발열을 고려하였으며 다양한 압력 영역(0.1MPa ~ 10MPa)에 대한 연소 특성을 살펴보았다. 모델링 영역을 1)물+알루미늄 2)증기+알루미늄 3)반응영역으로 나누었으며 영역의 방정식을 구성하고 화염속도에 대한 해석적 해를 구하였다. 입자크기에 따른 연소실 압력의 영향을 도출하여 시험결과와 비교, 분석 하였다.