• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.2
• /
• pp.137-143
• /
• 2012

Currently, in order to meet the reinforced emissions regulations for harmful exhaust gas including carbon dioxide ($CO_2$) as a greenhouse gas, technologies for reducing $CO_2$ emission and fuel consumption are being developed. Gasoline direct injection (GDI) systems have the advantage of improved fuel economy and higher power output than port fuel injection gasoline engine systems. The aim of this study is to examine the performance and emission characteristics of a lean burn GDI engine equipped with spray-guided-type combustion system. Stable lean combustion was achieved with a late fuel injection strategy under a constant operating condition. Further improvement in specific fuel consumption is possible with the introduction of multiple fuel injection strategies, which also increases hydrocarbon (HC) and nitrogen oxide ($NO_x$) emissions and decreases carbon monoxide (CO) emission.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.4
• /
• pp.614-621
• /
• 2002

This study was performed to investigate the behavior of vapor phase of fuel mixtures with different piston bowl shapes(F, B and R-type) in a optically accessible engine. The images of liquid and vapor phases were captured in the motoring engine using exciplex fluorescence method. Fuel was injected into atmospheric nitrogen to prevent quenching phenomenon by oxygen. Injection pressure was 5.1MPa. Two dimensional spray fluorescence image of vapor phase was acquired to analyze spray behaviors and fuel distribution inside of cylinder. Four injection timings were set at BTDC 90$^{\circ}$, 80$^{\circ}$, 70$^{\circ}$, and 60$^{\circ}$. With a fuel injection timing of BTDC 90$^{\circ}$, fuel-rich mixture level in the center region was highest in a B-type piston. With a fuel injection timing of BTDC 60$^{\circ}$, R-type piston was best. R-type piston shape was suitable under enhanced swirl ratio and late injection condition and B-type piston shape was right in a weak swirl ratio. It was found that the piston bowl shape affected the mixture stratification inside of cylinder.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.2027-2033
• /
• 2003

The purpose of this study is to investigate the stratification of fuel vapor with different in-cylinder flow, piston cavity and injection timings in an optically accessible engine. Three different piston shapes that are F(Flat), B(Bowl) and R(Re-entrance) types were used. The images of liquid and vapor fuel were captured under the motoring condition using Laser Induced Exciplex Fluorescence technique. As a result, at early injection timing of 270 BTDC, liquid fuel was evaporated faster by tumble flow than swirl flow, where most of fuel vapor were transported by tumble flow to the lower region and both sides of cylinder for the F-type piston. At late injection timing of 90 BTDC, tumble flow appears to be moving the fuel vapor to the intake side of the cylinder, while swirl flow convects the fuel vapor to the exhaust side. The concentration of mixture in the center region was highest in the B-type piston, while fuel vapor was transported to the exhaust side by swirl flow in F and R-type pistons. At the injection timing of 60 BTDC, the R-type piston was better for stratification due to a relatively smaller bowl diameter than the others.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.915-920
• /
• 2001

This study was performed to investigate the behavior of vapor phase of fuel mixtures with different piston bowl shapes(F, B, and R-type) in a optically accessible engine. The images of liquid and vapor phases were captured in the motoring engine using exciplex fluorescence method. Fuel was injected into atmospheric nitrogen to prevent quenching phenomenon by oxygen. Injection pressure is 5.1MPa. Two dimensional spray fluorescence image of vapor phases was acquired to analyze spray behaviors and fuel distribution inside of cylinder. Four injection timings were set at BTDC $90^{\circ},\;80^{\circ},\;70^{\circ},\;and\;60^{\circ}$. With a fuel injection timing of BTDC $90^{\circ}$, fuel-rich mixture level in the center region was highest in a B-type piston. With a fuel injection timing of BTDC $60^{\circ}$, R-type piston was best. R-type piston shape was suitable under enhanced swirl ratio and late injection condition and B-type piston shape was right in a weak swirl ratio. It was found that the piston bowl shape affected the mixture stratification inside of cylinder.

• Journal of ILASS-Korea
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2010

As world attention has focused on global warming and air pollution, high efficiency diesel engines with low $CO_2$ emissions have become more attractive. Premixed diesel engines in particular have the potential to achieve the more homogeneous mixture in the cylinder which results in lower NOx and soot emission. Early studies have shown that the operation conditions such as the EGR, intake conditions, injection conditions and compression ratio are important to reduce emissions in a PCCI (Premixed Charge Compression Ignition) engine. In this study a modified cam was employed to reduce the effective compression ratio. While opening timing of the intake valve was fixed, closing timing of the intake valve was retarded $30^{\circ}$. Although Atkinson cycle with the retarded cam leads to a low in-cylinder pressure in the compression stroke, the engine work can still be increased by advanced injection timing. On that account, we investigated the effects of various injection parameters to reduce emission and fuel consumption; as a result, lower NOx emission levels and almost same levels of fuel consumption and PM compared with those of conventional diesel engine cam timing could be achieved with the LIVC system.

• Speech Sciences
• /
• v.12 no.4
• /
• pp.203-213
• /
• 2005

This study was conducted to investigate the respiratory and aerodynamic function of adductor spasmodic dysphonia (ADSD) patients. Participants were (1) 18 females SD patients with non- Botulinum toxin injection (2) 14 females SD patients who had taken treatment of Botulinum toxin injection. (3) 14 age- and sex- matched normal female controls. Spirometer and phonatory function analyzer were used for respiratory muscle pressure (MIP: Maximum inspiratory pressure), MEP: Maximum expiratory pressure)& MPT(Maximum phonation time) and aerodynamic(F0:Fundamental frequency, intensity, MFR: Mean flow late, Psub: Subglottal pressure) measurement. The results were as follows: (1) Normal group was significantly higher in MIP, MEP, MPT than two SD groups (p < .05); (2) MPT was significantly lower in SD with non-Botulinum toxin injection group than SD with the treatment experience of Botulinum toxin injection (p < .05); (3) All aerodynamic parameters, F0, intensity, MFR, Psub, were not significantly different among three groups(p > .05).The reason of short MPT in ADSD may use lower respiratory pressure than normal group as strategy to decrease their tremulous voice quality. Moreover respiratory muscle pressure was lower than normal group regardless of botulinum toxin injection treatment.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.127-135
• /
• 2007

The objective of this study is to analyze the effect of velocity and vorticity on stratified mixture formation in the visualization engine. In order to investigate spray behavior, the pray velocity is obtained through the cross-correlation PIV method, a useful optical diagnostics technology and the vorticity calculated from the spray velocity component. These results elucidated the relationship between vorticity and entropy, which play an important role in the diffusion process for the early injection case and the stratification process for the late injection case. In addition, we quantified the homogeneous diffusion ate of spray using entropy analysis based on Boltzmann's statistical thermodynamics. Using these methods, we discovered that the homogeneous mixture distribution is more effective as a momentum dissipation of surrounding air than that of the spray concentration with a change in the injection timing. We found that the homogenous diffusion rate increased as the injection timing moved to the early intake stroke process, and BTDC $60^{\circ}$ was the most efficient injection timing for the stratified mixture formation during the compression stroke.

• Journal of Power System Engineering
• /
• v.21 no.1
• /
• pp.63-69
• /
• 2017

The combustion characteristics of gasoline and diesel were tested in a compression ignition engine. Both fuels were used with same common rail injection system. Combustion experiment showed that low load condition of 0.45 MPa IMEP (indicated mean effective pressure) was tested in metal and optical engines. The gasoline combustion showed higher hydrocarbon and carbon monoxide emissions but lower soot emission compared with diesel combustion. NOx emissions were very high at late injection timing but significantly decreased at early injection timing due to the lean combustion resulted from vigorous mixing process. Direct combustion visualization showed that the diesel combustion was dominated by diffusion combustion exhibiting soot incandescence and the gasoline combustion was mostly consisted of premixed combustion showing blue chemiluminescence.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.7-12
• /
• 2003

Mixture formation in the cylinder of a lean bum engine has been observed by Laser Induced Fluorescence technique. XeCl laser (308nm) was used to produce a laser sheet. 3-pentanone has been added to iso-octane fuel to produce fluorescence, the intensity of which is proportional to the concentration of the fuel. The laser sheet was introduced through the piston window and the fuel distribution in the vertical plane was observed through a side window. Comparison has been made for the cases of selected fuel injection timing as 0, 360, 405, and 450 CA. For the case of 0 and 360 CA injection, uniform fuel distribution in the combustion chamber has been obtained at the ignition time which is favorable for the high load mode. And the late injection cases, 405 and 450 CA, revealed the stratified formation of rich mixture around the spark plug. That extends the lean misfire limit and reduces cyclic variation in the low load mode.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.193-200
• /
• 2007

Natural gas is one of the most promising alternatives to gasoline and diesel fuels because of its lower harmful emissions, including $CO_2$, and high thermal efficiency. In particular, natural gas is seen as an alternative fuel for heavy-duty Diesel Engines because of the lower resulting emissions of PM, $CO_2$ and $NO_x$. Almost all CNG vehicles use the PFI-type Engine. However, PFI-type CNG Engines have a lower brake horse power, because of reduced volumetric efficiency and lower burning speed. This is a result of gaseous charge and the time losses increase as compared with the DI-type. This study was conducted to investigate the effect of injection conditions (early injection mode, late injection mode) on the combustion phenomena and performances in the or CNG Engine. A DI Diesel Engine with the same specifications used in a previous study was modified to a DI CNG Engine, and injection pressure was constantly kept at 60bar by a two-stage pressure-reducing type regulator. In this study, excess air ratios were varied from 1.0 to the lean limit, at the load conditions 50% throttle open rate and 1700rpm. The combustion characteristics of the or CNG Engine - such as in-cylinder pressure, indicated thermal efficiency, cycle-by-cycle variation, combustion duration and emissions - were investigated. Through this method, it was possible to verify that the combustion duration, the lean limit and the emissions were improved by control of injection timing and the stratified mixture conditions. And combustion duration is affected by not only excess air ratio, injection timing and position of piston but gas flow condition.