• Journal of the Korean Association of Geographic Information Studies
• /
• v.10 no.1
• /
• pp.1-9
• /
• 2007

3D data are in great demand for pedestrian navigation recently. For pedestrian navigation, we needs to reconstruct 3D model in detail from people's eye. In order to present spatial features in detail for pedestrian navigation, it is indispensable to develop 3D model not only in outdoor environment but also in indoor environment such as underground shopping complex. However, it is very difficult to acquire 3D data efficiently by mobile mapping without GPS. In this research, 3D shape was acquired by Laser scanner, and texture by CCD(Charge Coupled Device) sensor. Continuous changes position and attitude of sensors were measured by IMU(Inertial Measurement Unit). Moreover, IMU was corrected by relative orientation of CCD images without GPS(Global Positioning System). In conclusion, Reliable, quick, and handy method for acquiring 3D data for indoor environment is proposed by a combination of a digital camera and a laser scanner with IMU.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.7182-7188
• /
• 2015

Recently, to improve manual mapping method, digital mapping using high-resolution camera and laser scanner has increasingly attracted attention and the relevant study is reportedly on the rise. In this study, laboratory and field test which are intended to quantitatively analyze and estimate the weathering degree which is one of the engineering characteristics of tunnel face using laser scanner that integrates high-solution imaging technique have been conducted. In a bid to analyze correlation between reflectance of laser scanner and weathering degree, investigation of the factors influencing on reflectance was carried out. And to minimize the effect on RGB value which is one the critical influential factors on reflectance, modification equation obtained from lab test was proposed. Modification equation proposed in this study was verified by comparing the values before and after correction using the data obtained by scanning. Consequently, weathering index estimated by modified reflectance appeared very similar with dominant weathering degree and weathering ratio monitored at the field.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.2
• /
• pp.187-194
• /
• 2009

This study is to improve position accuracy by selecting proper a servo motor and applying FOC(Field Oriented Control) on developing a 3D terrestrial laser scanner. A 3D terrestrial laser scanner under developing has range of scanning of azimuth 360$^\circ$and elevation 270$^\circ$. It is implemented by precise controlling of a azimuth motor and a elevation motor. In the consequence of study, we have known that position accuracy of the motor can be able to be improved with constant torque of the motor by using FOC(Field Oriented Control). The control technic of the motor is possible to apply a 3D terrestrial laser scanner as well as a robotic total station.

• Design & Manufacturing
• /
• v.15 no.4
• /
• pp.65-71
• /
• 2021

In the early days of laser invention, it was simply used as a measuring tool, but as lasers became more common, they became an indispensable processing tool in the industry. Short-wavelength lasers are used to make patterns on wafers used in semiconductors depending on the wavelength, such as CO2 laser, YAG laser, green laser, and UV laser. At first, the hole of the PCB board mainly used for electronic parts was not thin and the hole size was large, so a mechanical drill was used. However, in order to realize product miniaturization and high integration, small hole processing lasers have become essential, and pattern exposure for small hole sizes has become essential. This paper intends to analyze the characteristics through patterns by exposing the PCB substrate through DMD and polygon scanner, which are different optical systems. Since the optical systems are different, the size of the patterns was made the same, and exposure was performed under the optimal conditions for each system. Pattern characteristics were analyzed through a 3D profiler. As a result of the analysis, there was no significant difference in line width between the two systems. However, it was confirmed that dmd had better pattern precision and polygon scanner had better productivity.

• Laser Solutions
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2015

High welding speed and narrow weld seam are favorable for welding of magnesium alloy. Magnesium alloy is recommended for the smart frame because it has several advantages such as low density, high thermal conductivity, EMI shielding capability and good cast ability. This study is for the assembly welding of the magnesium smart frame with high productivity, good performance and low cost. The window for battery on AZ91D frame produced by die-casting was prepared by CNC machining. Corresponding AZ31 blank of 0.2mm thickness was prepared by die-blanking cut. All system set was fixed at the stationary bed but the laser beam was manipulated by scanner up-to 1,000mm/s speed. The weld joint between AZ31 sheet and AZ91D frame was welded by fiber laser on 850~1,000W output power. The joint showed penetration enough but some humping bead. The distortion by the weld heat was almost free because of the quick dissipation of the heat by small beam size and fast welding. Consequently, the thinner magnesium foil was assembled successfully to the magnesium frame of mobile phone.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.969-970
• /
• 2009

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.621-626
• /
• 2021

In this study, data on the study site for apartment construction was acquired, and the quantity of construction waste was calculated using a drone and mobile 3D laser scanner. The accuracy of the drone was 0.034 to 0.064m in the horizontal and vertical directions, respectively, and the mobile 3D Laser Scanner showed an accuracy of 0.018 to 0.049m in the horizontal direction, respectively. These results suggest that it is possible to construct spatial information using a drone and mobile 3D laser scanner with a value within the allowable accuracy of 1:1,000 digital terrain. The volume of construction waste calculated using the mobile 3D laser scanner data was 70,797㎥. It was possible to calculate the volume on the side of the building or some facilities that appeared as shaded areas in the drone outcomes. In addition, modeling was performed for view analysis of the apartments scheduled to be constructed and the terrain-based modeling results of the surrounding buildings. In the future, data construction and accuracy evaluation using mobile 3D laser scanners will be conducted. In addition, additional research comparing existing methods and work processes will be carried out, and the efficiency of mobile 3D laser scanners in the field of spatial information construction can be presented.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2006

Effective three dimensional modeling becomes essential in a wide range of drawings, such as construction, machinery and design. In particular, it has been developed as the tool enabling reverse design. Three dimensional modeling requires rapidity, accuracy and tangibility. Data acquisition methods for modeling including contact type coordinate measurement machine, LASER scanner, pattern scanner and digital photogrammetry. In this study, we try to analyze modeling techniques as well as introduce three dimensional modeling using pattern scanner. In addition, this study conducts three dimensional modeling using OPTO-Top pattern scanner with distinguished accuracy and rapidity, and then compare efficiency with digital photogrammetry. And, this study attempts to form environment that enables to turn around models on web in three dimensional ways.

• Laser Solutions
• /
• v.13 no.4
• /
• pp.14-20
• /
• 2010

Robot path generation and laser welding technology for manufacturing automotive body are studied. Laser welding and industrial robot systems are used with the robot based laser welding system. The laser system used in this study is 1.6kW Fiber laser, while the robot system is 6 axes Industrial robot (payload: 130kg). The robot based laser welding system is equipped with laser scanner system for remote laser welding. The laser source, robot and laser scanner system are used to increase the processing speed and to improve the process efficiency. The welding joints of steel plate are butt and lapped joints. The quality test of the laser welding are through the observation the shape of bead on plate and cross-section of welding part. The 3 dimensional laser welding for non-linear pipe welding line is performed. This paper introduces the robot based laser welding system to resolve the limited welding speed and accuracy of the conventional spot welding system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.1 s.173
• /
• pp.269-274
• /
• 2000

Frictions and electrical contact voltages of the herringbone-grooved hydrodynamic bearing(HHB) were 9, measured to use in a laser scanner motor. This bearing with varying loads, speeds, oil viscosity, and radial clearances successfully operated up to 28,000rpm and 0.5N. Experimental results under various environments confirmed that this bearing had excellent performance with low friction force, and operated without contact between shaft and sleeve.