• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.353-356
• /
• 2002

Planar laser induced fluorescence(PLIF) has been widely used to obtain two dimensional fuel distribution. Preliminary investigation was performed to measure quantitative air excess ratio distribution in an engine fueled with LPG. It is known that fluorescence signal from acetone as a fluorescent tracer is less sensitive to oxygen quenching than other dopants. Acetone was excited by KrF excimer laser (248nm) and its fluorescence image was acquired by ICCD camera with a cut-of filter to suppress Mie scattering from the laser light. For the purpose of quantifying PLIF signal, an image processing method including the correction of laser sheet beam profile was suggested. Raw images were divided by each intensity of laser energy and profile of laser sheet beam. Inhomogeneous fluorescence images scaled with the reference data, which was taken by a calibration process, were converted to air excess ratio distribution. This investigation showed instantaneous quantitative measurement of planar air excess ratio distribution for gaseous fuel.

• 한국레이저가공학회지
• /
• 제3권2호
• /
• pp.25-33
• /
• 2000

One of perspective direction of microfabrication is direct laser writing technology that allows to create metal, semiconductive and dielectric micropatterns on substrate surface. In this work, a two step method, the combination of seed forming process, in which metallic Al seed was selectively generated on AlN ceramic substrate by direct writing technique using a pulsed Nd : YAG laser and subsequent electroless Ni plating on the activated Al seed, was presented. The effects of laser parameters such as pulse energy, scanning speed and pulse frequency on shape of Alseed and conductor line after electroless Ni plating were investigated. The nature of the laser activated surface is analyzed from XPS data. The line width of this metallic Al and Ni is analyzed using SEM. As a results, Al seed line with 24㎛ width and 100㎛ isolated line space is obtained. Finally, laser direct writing can be applied in the field between thin and thick film technique in electronic industry.

• 한국레이저가공학회지
• /
• 제11권3호
• /
• pp.21-24
• /
• 2008

Hybrid laser welding technology is a good process to reduce a thermal distortion and increase the productivity. However, it requires a high investment and a massive modification of the fabrication line such as a gantry system, milling machine for the edge preparation, high power laser system and weld machine. Therefore the development of an economical laser welding system is a crucial point to apply this system in shipbuilding yard. In this study, a portable hybrid laser welding carriage was developed for I-butt joint without edge milling. It is expected that the carriage type system could reduce investment cost.

• Journal of Welding and Joining
• /
• 제15권3호
• /
• pp.99-108
• /
• 1997

For the conventional welding method, the high heat transfer makes the crystallization of the work material unavoidable. Whereas the laser is able to weld the amorphous metal without a crystallized zone, because heat transfer is limited withn a very small restricted volume. In this paper, the possibilities and the limits of the laser welding in a deep frozen environment by liquid nitrogen were studied to utilize the advantageous properties of amorphous metal foils. The author investigated, after laser welding in a deep frozen environment with a solid state laser (Nd:YAG-laser), the achievable strengths and the influences of the laser beam parameters on the strengths.

• 소성∙가공
• /
• 제20권8호
• /
• pp.575-580
• /
• 2011

Direct laser melting(DLM) is promising as a joining method for producing parts for automobiles, aerospace, marine and medical applications. An advantageous characteristic of DLM is that it affects the parent metal very little. The mechanical properties of parts made by DLM are strongly affected by the porosity and surface roughness of the laser melted beads. This is a systematic study of the effects of the porosity and surface roughness of laser melted beads using various processing parameters, such as laser power, scan rate and overlapping ratio of the fill spacing. The specimens were fabricated with 316L and 304L austenitic stainless steel powder. Dense parts with low porosity were obtained at low laser scan speed, as it increased the aspect ratio of the parental material and the depth of penetration. The variations of surface roughness were examined at various processing parameters such as overlapping ratio and laser power.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2001년도 춘계학술발표대회 논문개요집
• /
• pp.31-34
• /
• 2001

Laser cladding Processing allows rapid transfer of heat to the material being minimum conduction into base metal. The effects of CO$_2$ laser cladding with high powder were investigated. High viscosity bronze powder consists of bronze powder used at a high temperature. The material has a high viscosity So that it can be substrate. Therefore. Laser cladding can be processed on a curved or slope surface. CO$_2$ laser cladding was designed It consists of the high viscosity bronze powder the shielding gas system and the preheating system The high viscosity powder properly at 0.3g/s and 0.50g/s. Because of the metallic bond between bronze per the hardness of dilution layer was suddenly increased. Experimental as results viscosity mixed powder can be a useful cladding material.

• 한국레이저가공학회지
• /
• 제15권4호
• /
• pp.16-19
• /
• 2012

Due to the fact that the dimensions of circuit lines of IC substrates have been forecast to reduce rapidly, engraving the circuit line patterns with laser has emerged as a promising alternative. To engrave circuit line patterns in an IC substrate, we used a projection ablation technique in which a metal (INVAR) mask and a DPSS UV laser instead of an excimer laser are used. Results showed that the circuit line patterns engraved in the IC substrate have a width of about 15um and a depth of $13{\mu}m$. This indicates that the projection ablation with a metal mask and a DPSS UV laser could feasibly replace the semi-additive process (SAP).

• 한국레이저가공학회지
• /
• 제15권2호
• /
• pp.1-5
• /
• 2012

Gelatin is used as a model for soft biological tissues in studying laser interaction with the soft tissues. In this work, we analyze the interaction between gelatin and excimer and Ti:Sapphire femtosecond laser under various conditions, especially by varying the laser, laser fluence and pulse number. The results show that swelling of the surface and ablation depth can be controlled by adjusting the process parameters.

• 한국정밀공학회지
• /
• 제18권1호
• /
• pp.139-146
• /
• 2001

This paper presents a study on heat transfer and residual distortion analysis of laser welded EDFA(Erbium Doped Fiber Amplifier) LD(Laser Diode) Pump using the finite element method. In the production process of LD Pump in light-wave communication system, ferrule and saddle are welded by Nd-YAG laser. These parts experience thermal and mechanical effect during heating and cooling cycle with the laser welding. Thus distortion happens in the laser-welded packaging, and it makes an error in detecting the light signal translate through optical fiber in LD Pump. The amount of final displacement produced by the laser welding is predicted using the finite element method. And the optimal shape of saddle is proposed with the results of numerical analyses to minimize the displacement.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.743-744
• /
• 2008