• 대한기계학회논문집B
• /
• 제20권11호
• /
• pp.3630-3638
• /
• 1996

An experimental study has been conducted to explore the behaviors of the radiative ignition of polymethylmetacrylate(PMMA) in a confined enclosure such as the ignition delay time, PMMA surface temperature, the ignition location and the ignition process. In addition, the effects of hot wall orientation on the ignition delay and PMMA surface temperature were studied. When the hot wall is located at the bottom, ignition delay time is the shortest. Ignition surface temperature becomes the lowest for the hot top wall case. These are due to buoyancy effect. Since the radiative heat flux of hot wall is rather lower than laser source, the ignition is considered to be controlled by the mixing process. Therefore, the ignition location, where appropriate mixture of fuel and oxygen exists, occurs near the hot wall. The flame propagates along the hot wall where there exists sufficient oxygen.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.213-214
• /
• 2015

Breakup and ignition of single droplet were experimentally investigated using two independent Nd-YAG lasers. The emulsified fuel was made from n-dodecane and water while varying the relative volumetric fraction. As a result of visualization, breakup and ignition behaviors were dependent on the fraction. Luminosity from the secondary droplets increased as the water fraction decreased. Ignition did not occur below 80% of the n-dodecane fraction.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1995년도 제4회 학술강연회논문집
• /
• pp.157-168
• /
• 1995

Ignition of a reactive solid with rough surface by constant heat flux is studied. The geometry of surface is represented by a protrusion in shape of cone of infinite length. Ignition time and ignition criterion versus apex angle are determined, with the use of heterogeneous model of ignition. To study the effect of geometry on ignition the results are compared with the known results for the one-dimensional ignition of the semi-infinite body. It is shown, that: a) ignition time depends strongly upon the apex angle and is proportional to the angle to the second power; b) ignition criterion and ignition temperature do not depend strongly on angle. The ignition delay and the energy required for the successful ignition are substantially reduced compared to the one-dimensional case.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2015년도 제51회 KOSCO SYMPOSIUM 초록집
• /
• pp.215-218
• /
• 2015

Simultaneous laser ignition and spectroscopy is a scheme that enables rapid determination of the local equivalence ratio and condensed fuel concentration during a reaction in a two phase spray flame. We have conducted quantitative analysis of the LIBS signals according to the equivalence ratio, droplet size, droplet number density and droplet concentration as a part of novel feedback control strategy proposed for flame ignition and stabilization with simultaneous in situ combustion flow diagnostics. This is a desirable scheme since such real time information onboard an engine for instance can be constantly monitored and fed back to the control loop to enhance the mixing process and minimize emissions of unwanted species and potential combustion instability.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.51-54
• /
• 2008

레이저는 다양한 빔 에너지의 분포 형상을 가질 수 있으며 크게 정형화된 분포 형상은 모드로 구분하여 모드에 따른 빔 에너지 분포 형상은 예측이 가능하다. 본 연구에서는 고에너지의 빔 분포 형상에 따른 steel의 가열 모델을 제시하고 빔 분포 형상에 따른 가열 패턴의 예측과 비교를 수행하였으며, 가열 패턴이 폭약의 점화에 미치는 영향에 대해 논의 하였다.

• Journal of Mechanical Science and Technology
• /
• 제16권6호
• /
• pp.829-838
• /
• 2002

A constant volume combustion chamber is used to investigate the flame kernel development of gasoline air mixtures under various ignition systems, ignition energies and spark plugs. Three kinds of ignition systems are designed and assembled, and the ignition energy is controlled by the variation of the dwell time. Several kinds of spark plugs are also tested. The velocity of flame propagation is measured by a laser deflection method, and the combustion pressure is analyzed by the heat release rate and the mass fraction burnt. The results represent that as the ignition energy is increased by enlarging either dwell time or spark plug gap, the heat release rate and the mass fraction burnt are increased. The electrodes materials and shapes influence the flame kernel development by changing he transfer efficiency of electrical energy to chemical energy. The diameter of electrodes also influences the heat release rate and the burnt mass fraction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.864-870
• /
• 2001

Flame propagation along vortex tube was experimentally investigated. The vortex tube was generated by the ejection of propane from a nozzle through a single stroke motion of a speaker and the ignition was induced from a single pulse laser. Non-reactive flow fields were visualized using shadow technique. From these images, vortex ring size and translational velocity were measured in order to determine the ignition time and position. Flame structure and flame speed were measured using high speed CCD camera. Flame speed was accelerated during the initial stage of flame kernel growth, and reached near constant value during steady propagation period. Near the completion of propagation, flame speed was decelerated and then extinguished. Flame speed along the non-premixed vortex tube was found to be linearly proportional to circulation, which was similar to that of the flame propagation along premixed vortex ring. Ignition position minimally affects the propagation characteristics. These imply that flame is propagating along the maximum speed locus expected to be along stoichiometric contour and also support the existence of tribrachial flames.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2001년도 제17회 학술발표회 논문초록집
• /
• pp.50-53
• /
• 2001

Flame propagation during the initial stages of ignition in a non-premixed swirl, having some of characteristics of the primary zone of an aero gas turbine combustor, has been investigated. Nd:YAG laser was adopted as the principal ignition source to allow arbitrary placing of the ignition site i subsequent flame development was monitored using a natural light high speed filming technique for many ignition site at two different swirl ratios and an overall equivalence ratio of 0.9. For ignition offset from the burner centreline, buoyancy force associated with radial pressure gradient produced a strong inward movement of the flame kernel. At the burner exit. flame kernels invariably developed into cylindrical form and a 'radial confinement /axia expansion' (RCAE) process was observed.

• 한국자동차공학회논문집
• /
• 제23권6호
• /
• pp.650-655
• /
• 2015

A high energy ignition system is essential for lean burn or high EGR gasoline engine, which is getting more and more interest to improve fuel economy. The high energy ignition systems comprise plasma jet, laser beam, corona discharge and so on. In this study, a high energy ignition system using corona discharge is developed and tested in a constant volume combustion chamber. The developed system shows extension of lean limit of propane-air mixture and enhencement of combustion speed. Various shape of corona discharge plugs are also tested and compared in this study.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2003년도 하계학술발표회
• /
• pp.6-7
• /
• 2003

The inertial fusion research at ILE, Osaka moves to the fast ignition scheme with using PW laser system to achieve hot core plasma of keV-temperature by heating additionally the dense plasma imploded by the multi-beam Gekko laser system. The solid-state lasers have been developed of the peak-power from TW to PW region with the chirped pulse amplification (CPA) and optical parametric amplification (OPA) technology. (omitted)