• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1314-1317
• /
• 2006

The problem of the conflict between eye convergence and accommodation can be induced at Stereoscopic or multi-view 3D display system using binocular disparity. A multi-focus 3D display system was developed, which can solve the problem. LEDs are used instead of galvano scanner and laser to avoid mechanical moving part at the 3D display system.

• ETRI Journal
• /
• v.36 no.2
• /
• pp.232-241
• /
• 2014

A holographic display system with a 22-inch LCD panel is developed to provide a wide viewing angle and large holographic 3D image. It is realized by steering a narrow viewing window resulting from a very large pixel pitch compared to the wave length of the laser light. Point light sources and a lens array make it possible to arbitrarily control the position of the viewing window for a moving observer. The holographic display provides both eyes of the observer with a holographic 3D image using two vertically placed LCD panels and a beam splitter to support the holographic stereogram.

• Journal of the Korea Convergence Society
• /
• v.8 no.5
• /
• pp.161-167
• /
• 2017

We have fabricated and characterized $32{\times}32$ photonic quantum ring (PQR) laser arrays uniformly operable with $0.98{\mu}A$ per ring at room temperature. The typical threshold current, threshold current density, and threshold voltage are 20 mA, $0.068A/cm^2$, and 1.38 V. The top surface emitting PQR array contains GaAs multiquantum well active regions and exhibits uniform characteristics for a chip of $1.65{\times}1.65mm^2$. The peak power wavelength is $858.8{\pm}0.35nm$, the relative intensity is $0.3{\pm}0.2$, and the linewidth is $0.2{\pm}0.07nm$. We also report the wavelength division multiplexing system experiment using angle-dependent blue shift characteristics of this laser array. This photonic quantum ring laser has angle-dependent multiple-wavelength radial emission characteristics over about 10 nm tuning range generated from array devices. The array exhibits a free space detection as far as 6 m with a function of the distance.

• Journal of Convergence for Information Technology
• /
• v.9 no.5
• /
• pp.117-124
• /
• 2019

This paper discusses recent trends in the fabrication of semiconducting materials among the components of thin film transistors used in AMOLED display. In order to obtain a good semiconductor film, it is necessary to change the amorphous silicon into polycrystalline silicon. There are two ways to use laser and heat. Laser-based methods include sequential lateral solidification (SLS), excimer laser annealing (ELA), and thin-beam directional crystallization (TDX). Solid phase crystallization (SPC), super grain silicon (SGS), metal induced crystallization (MIC) and field aided lateral crystallization (FALC) were crystallized using heat. We will also study research for manufacturing large AMOLED displays.

• Journal of Convergence for Information Technology
• /
• v.10 no.6
• /
• pp.28-34
• /
• 2020

A structure in which GaAs and AlGaAs epilayers are formed with a metal organic chemical vapor deposition equipment on a GaAs wafer similar to the structure of making a vertical cavity surface emitting laser is used. Photonic Quantum Ring (PQR) devices that are naturally generated by 3D resonance are manufactured by chemically assisted ion beam etching technology, which is a dry etching method. A new technology that can be fabricated has been studied, and as a result, the possibility of wet etching of a solution containing phosphoric acid, hydrogen peroxide and methanol was investigated, and the device fabrication by applying this method are also discussed. In addition, the spectrum of the fabricated optical device was measured, and the results were theoretically analyzed and compared with the wavelength value obtained by the measurement. It is expected that the PQR device will be able to model cells in a three-dimensional shape or be applied to the display field.

• Tribology and Lubricants
• /
• v.38 no.3
• /
• pp.93-100
• /
• 2022

Micro-light emitting diode (micro-LED) displays offer numerous advantages such as high brightness, fast response, and low power consumption. Hence, they are spotlighted as the next-generation display. However, defective LEDs may be created due to non-uniform contact loads or LED alignment errors. Therefore, a repair process involving the replacement of defective LEDs with favorable ones is necessitated. The general repair process involves the removal of defective micro-LEDs, interconnection material transfer, as well as new micro-LED transfer and bonding. However, micro-LEDs are difficult to repair since their size decreases to a few tens of micron in width and less than 10 ㎛ in thickness. The conventional nozzle-type dispenser for fluxes and the conventional vacuum chuck for LEDs are not applicable to the micro-LED repair process. In this study, transfer conditions are determined using a micro stamp for repairing micro-LEDs. Results show that the aging time should be set to within 60 min, based on measuring the aging time of the flux. Additionally, the micro-LEDs are subjected to a compression test, and the result shows that they should be transferred under 18.4 MPa. Finally, the I-V curves of micro-LEDs processed by the laser and hot plate reflows are measured to compare the electrical properties of the micro-LEDs based on the reflow methods. It was confirmed that the micro-LEDs processed by the laser reflow show similar electrical performance with that processed by the hot plate reflow. The results can provide guidance for the repair of micro-LEDs using micro stamps.

• Journal of Convergence for Information Technology
• /
• v.9 no.3
• /
• pp.75-81
• /
• 2019

In this work, we investigated a low temperature polycrystalline silicon (LTPS) thin film transistors fabrication process on polymer layers. Dehydrogenation and activation processes were performed by a furnace annealing at a temperature of $430^{\circ}C$ for 2 hr. The crystallization of amorphous silicon films was formed by excimer laser annealing (ELA) method. The p-type device performance, fabricated by polycrystalline silicon (poly-Si) films, shows a very good performance with field effect mobility of $77cm^2/V{\cdot}s$ and on/off ratio current ratio > $10^7$. We believe that the poly-Si formed by a LTPS process may be well suited for fabrication of poly-Si TFTs for bendable panel displays such as AMOLED that require circuit integration.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.55-60
• /
• 2021

In order to produce wearable displays with high adhesion while maintaining flexible characteristics, the adhesive method using electro plating method was carried out. Laser lift-off (LLO) transcription was also used to remove sapphire substrates from LEDs bonded to fibers. Afterwards, the SEM and EDS data of the sample, which conducted the adhesion method using electro plating, confirmed that copper actually grows through the lattice of the fiber fabric to secure the light source and fiber. The adhesion characteristics of copper were checked using Universal testing machine (UTM). After plating adhesion, the characteristics of the LLO transcription process completed and the LED without the transcription process were compared using probe station. The electroluminescence (EL) according to the enhanced current was measured to check the characteristics of the light source after the process. As the current increases, the temperature rises and the bandgap decreases, so it was confirmed that the spectrum shifted. In addition, the change in the electrical characteristics of the samples according to the radius change is confirmed using probe station. The radius strain also had mechanical strength that copper could withstand bending stress, so the Vf variation was measured below 6%. Based on these results, it is expected that it will be applied to batteries, catalysts, and solar cells that require flexibility as well as wearable displays, contributing to the development of wearable devices.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1563-1568
• /
• 2012

Printed electronics is a technology used for forming electronic circuits or devices, and it is used in the manufacture of many products such as RFID tags, solar cells, and flexible display panels with a much lower cost than in the case of semiconductor process technology. Web-guide-type printing such as roll-to-roll printing is a method used to produce printed electronic devices in a large volume. To commercialize such products, highly precise alignment between printed layers is required. In this study, a highly precise alignment system is proposed, and some experimental results are compared with those obtained using a laser surface vibrometer to illustrate the reliability of the proposed system. The robustness of the proposed system to web deformation is also considered experimentally.