• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.751-757
• /
• 2001

An experimental study of impinging jet-flow structure has been carried out for a fully developed single circular jet impingement cooling on a flat plate, and the effect of the wall thickness at nozzle exit edge is investigated. Impinging jet flow structures have been measured by Laser-Doppler Velocimeter to interpret the heat transfer results presented previously by Yoon et al.(sup)(10) The peaks of heat transfer rate are observed near the nozzle edge owing to the radial acceleration of jet flow when the nozzle locates close to the impingement plate. The growth of the velocity fluctuations in the wall jet flow is induced by the vortices which originate in the jet shear layer, and consequently the radial distribution of local Nusselt numbers has a secondary peak at the certain radial position. As a wall of circular pipe nozzle becomes thicker for small nozzle-to-target distance, the entrainment can be inhibited, consequently, the acceleration of wall jet flow is reduced and the heat transfer rate decreases.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.989-995
• /
• 2010

This paper is focused on a simplified measurement of rail irregularity by some axle-box accelerometers for high-speed rail condition monitoring with in-service high-speed trains. Generally, the rail condition monitoring has been done by a special railway inspection vehicle with a 10m versine method. But, the monitoring method needs some expensive measurement system, and have been performed only at night due to its speed limit. In this research, a simplified measurement of rail irregularity using axle-box accelerometers is proposed to monitor the rail condition with in-service high-speed trains. The acceleration is measured by using two accelerometers on a axle-box, and stored in an on-board data acquisition system. The displacement is estimated from the acceleration data by a combination of Kalman filter and the frequency selective filter. The estimated results are compared with the measurement from a laser rail inspection system which is near the axle-box. From the comparison, the proposed method shows promise as a tool for the simplified measurement of rail irregularity at high-speed.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.4
• /
• pp.22-25
• /
• 2008

The dynamic response of the head arm assembly (HAA) of a hard disk drive to an impact load was obtained from a 3D non-linear finite element model using ANSYS/LS-DYNA and from experiments using a modified levitation mass method (LMM). In the finite element model, the impact load was created by modeling the mass as a rigid body and making it collide with the HAA. The velocity, displacement, acceleration, and inertial force of the mass were then obtained from the time history data of the finite element analysis. In the LMM, a mass that was levitated with an aerostatic linear bearing, and hence encountered negligible friction, was made to collide with the actuator arm, resulting in a dynamic bending test for the arm. During the collision, the Doppler frequency shift of the laser beam reflected from the mass was accurately measured with an optical interferometer. The velocity, displacement, acceleration, and inertial force of the mass were accurately calculated from the measured time-varying Doppler frequency shift. A good correlation between the experimental data and FEA results was observed. The FEA was also used to investigate the dynamic response of the HAA to impact by different masses.

• ETRI Journal
• /
• v.33 no.4
• /
• pp.487-496
• /
• 2011

Korea Multi-Purpose Satellite-5 (KOMPSAT-5) is the first satellite in Korea that provides 1 m resolution synthetic aperture radar (SAR) images. Precise orbit determination (POD) using a dual-frequency IGOR receiver data is performed to conduct high-resolution SAR images. We suggest orbit determination strategies based on a differential GPS technique. Double-differenced phase observations are sampled every 30 seconds. A dynamic model approach using an estimation of general empirical acceleration every 6 minutes through a batch least-squares estimator is applied. The orbit accuracy is validated using real data from GRACE and KOMPSAT-2 as well as simulated KOMPSAT-5 data. The POD results using GRACE satellite are adjusted through satellite laser ranging data and compared with publicly available reference orbit data. Operational orbit determination satisfies 5 m root sum square (RSS) in one sigma, and POD meets the orbit accuracy requirements of less than 20 cm and 0.003 cm/s RSS in position and velocity, respectively.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.1
• /
• pp.8-15
• /
• 2007

Speech intelligibility of the eavesdropping sound is investigated on a acoustic cavity - glass window coupled system. Using MLS (Maximum Length Sequency) signal as a sound source, acceleration and velocity responses of the glass window are measured by accelerometer and laser doppler vibrometer. MTF (Modulation Transfer Function) is used to identify tile speech transmission characteristics of the cavity and window system. STI (Speech Transmission Index) based upon MTF is calculated and speech intelligibility of the vibration sound of the glass window is estimated. Speech intelligibilities by the acceleration signal and the velocity signal are compared. Finally, intelligibility of the conversation sound is confirmed by the subjective test.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.2
• /
• pp.202-209
• /
• 2014

In this paper, a developed device for detecting target's location and avoiding collision is proposed. Velocity and acceleration model of target are derived to estimate target's information, i.e. position, velocity and acceleration considering process and measurement noise. Kalman filtering method applied to the estimation process and its results was confirmed by simulation. The distance measurements system using laser sensor for moving target system is also developed to confirm the effectiveness of the proposed scheme. Experiments to get information of moving target with velocity and acceleration model was executed. The data with filtering and without filtering was compared by experiments. Discontinuous measured data was changed to smooth and continuous data by Kalman filtering. It is confirmed that desired data was obtained by applying proposed scheme. UI for measuring and monitoring the target data is developed and visual and auditory alarm function is attached on the system Finally, position estimation system of moving target with good performance is achieved by low price equipments.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.64-73
• /
• 2012

In this paper, a new land preview system using laser range finder based on heave estimation algorithm is proposed. The proposed land preview system is an equipment which measures the shape of forward topography for autonomous vehicle. To implement this land preview system, the laser range finder is generally used because of its wide measuring range and robustness under various environmental condition. Then the current location of the vehicle has to be known to generate the shape of forward topography and sensors based on acceleration such as IMU and accelerometer are generally utilized to measure heave motion in the conventional land preview system. However the drawback to these sensors is that they are too expensive for low-cost vehicle such as mobile robot and their measurement error is increased for mobile robot with abrupt acceleration. In order to overcome this drawback, an algorithm that estimates heave motion using the information of odometer and previously measured topography is proposed in this paper. The proposed land preview system based on the heave estimation algorithm is verified through simulation and experiments for various terrain using a simulator and a real system.

• Structural Engineering and Mechanics
• /
• v.42 no.2
• /
• pp.229-245
• /
• 2012

Bridge vibration displacements have been directly measured by LVDTs (Linear Variable Differential Transformers) or laser equipment and have also been indirectly estimated by an algorithm of integrating measured acceleration. However, LVDT measurement cannot be applied for a bridge crossing over a river or channel and the laser technique cannot be applied when the weather condition is poor. Also, double integration of accelerations may cause serious numerical deviation if the initial condition or a regression process is not carefully controlled. This paper presents an algorithm of estimating bridge vibration displacements using vibration strains measured by FBG (Fiber Bragg Grating) sensors and theoretical mode shapes of a simply supported beam. Since theoretically defined mode shapes are applied, even high modes can be used regardless of the quality of the measured data. In the proposed algorithm, the number of theoretical modes is limited by the number of sensors used for a field test to prevent a mathematical rank deficiency from occurring in computing vibration displacements.89The proposed algorithm has been applied to various types of bridges and its efficacy has been verified. The closeness of the estimated vibration displacements to measured ones has been evaluated by computing the correlation coefficient and by comparing FRFs (Frequency Response Functions) and the maximum displacements.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.354-358
• /
• 2006

A silicon lens and an insulator of pyrex, components of a micro-electron column, should be assembled by aligning and stacking simultaneously. An optical alignment of a diffraction beam and a laser welding were employed for the assembly of a source lens and an Einzel lens with precision within $\pm$4% for the maximum aperture size. The experimental condition for optical alignment and laser welding are explained. Anodic bonding was used to assist in stacking lenses. A micro-electron column of smaller apertures assembled with precise alignment and fabrication was tested with a current image of a Cu grid of 9$\mu$m in linewidth, and showed a higher resolution in acceleration mode.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.55-63
• /
• 1999

The acceleration of the performance of machine tools influences the development of the semi-conductor and optical technology as the development of NC and measurement technology. Because the measurement has been done to unload condition without considering of mechanical stiffness in the case of machining center as we measure the quasi-static error of machine tools on general study people who works on the spot has many problems on the data value. Also there are no satisfiable results until now in spite of many studys about this because the deflections of the table and the shaft supporting a workpiece influence, influence the accuracy of the table and shaft supporting a workpiece influence the accuracy of the workpiece. And there is doubt about the inspection method of measured error. In this paper Therefor we will help working more accurately on the spot by measuring analyzing displaying the defoec-tion of the table and support shaft when we load on the table and the support shaft of machining center using laser interfer-ometer. Also we try to settle new conception of the measurement method and more accurate grasp of the deflection tenden-cy by verifing the tendency of the error measured through the comparison of the simulated error measured through the comparison of the simulated error using ANSYS a common finite element analysis program which is able to measure heat deformation material deformation and error resulted from this study.