• Biomedical Science Letters
• /
• v.14 no.3
• /
• pp.173-178
• /
• 2008

With the widespread use of laser in medical and industrial settings, the incidence of laser injury to the ocular continues to grow among workers involved in handling lasers. The aim of this study is to compare ocular damages after irradiation with various laser wavelengths and power density. Ocular of pigmented rats was irradiated with $CO_2$ laser, 1064 nm Nd:YAG laser, and 532 nm diode laser. We observed damage of cornea, lens, and retina using slit lamp microscope and funduscopy. H&E staining of histopathology were applied to study the specimens. The higher exposure ($200mW/cm^2$, 10 sec) with $CO_2$ laser resulted in severe damage at the cornea. For the 1064 nm Nd:YAG laser, the higher exposure than $10mW/cm^2$ (10 sec) resulted in damage at the cornea and lens. Further, with the 532 nm diode laser, retinal lesions were induced when $10mW/cm^2$ (0.25 sec) was delivered to the eye. Theses results suggest that the ocular damages are different from various laser wavelength and power density.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.268-272
• /
• 2004

Transparent materials such as fused silica are widely utilized in optical and optoelectronics field because of its outstanding properties, such as transparency in a wide wavelength range, strong damage resistance for laser irradiation, and high thermal and chemical stability. In this study, we made a few micro patterns on the surface of fused silica plate using laser induced wet etching. KrF excimer laser was used as a light source. There were no burrs and micro cracks on the etched surface of fused silica and the flatness of the etched surface was fairly good. We investigated the influence of etchant upon the etch rate and quality in laser induced wet etching. Pyrene-acetone solution and toluene were used as etchant. In the side of etch rate, toluene solution was better than pyrene-acetone solution. But we made in wider range of energy density using pyrene-acetone solution. But pyrene-acetone solution gave us wider window of energy density for successful micro patterning.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.245-249
• /
• 2004

Transparent materials such as fused silica are important materials in optical and optoelectronics field because of its outstanding properties, such as transparency in a wide wavelength range, strong damage resistance for laser irradiation, and high thermal and chemical stability. However, these properties make it difficult to micromachine silica in micro-sized quantities. In this study, we fabricated a micro patterns on the surface of fused silica plate using laser induced wet etching. KrF excimer laser was used as a light source. There were no burrs and micro cracks on the etched surface of fused silica and the flatness of the etched surface was fairly good. We investigated the influence of etchant upon the etch rate and quality in laser induced wet etching. Pyrene-acetone, toluene, and pyrene-toluene solution were used as etchant. In the side of etch rate, toluene and pyrene-toluene solution were better than pyrene-acetone solution.

• Journal of the Optical Society of Korea
• /
• v.18 no.1
• /
• pp.50-54
• /
• 2014

In this paper we studied the laser-induced crater depth, mass, and emission spectra of laser-ablated high-density polyethylene (HDPE) polymer using the laser-induced plasma spectroscopy (LIPS) technique. This study was performed using a Nd:YAG laser with 100 mJ energy and 7 ns pulse width, focused normal to the surface of the sample. The nanoscale change in ablated depth versus number of laser pulses was studied. By using scanning electron microscope (SEM) images, the crater depth and ablated mass were estimated. The LIPS spectral intensities were observed for major and minor elements with depth. The comparison between the LIPS results and SEM images showed that LIPS could be used to estimate the crater depth, which is of interest for some applications such as thin-film lithography measurements and online measurements of thickness in film deposition techniques.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.459-462
• /
• 1999

Recent advances in NLO Borate Crystals for UV Generation are reviewed with the particular emphasis on the technique to improve the life time of UV optics. The laser-damage resistance of CLBO and fused silica surfaces was successfully improved after removing polishing compound by ion beam etching. The polishing compound embedded in the CLBO and fused silica surfaces were to a depth of less than 100nm. We were able to remove polishing compound without degrading the surface condition when the applied ion beam voltage was less than 200 V. The laser-induced surface damage threshold of CLBO was improved up to 15J/$\textrm{cm}^2$(wavelength: 355 nm, pulse width: 0.85 ns)as compared with that of the as-polished surface (11 J/$\textrm{cm}^2$). The laser-induced surface damage of fused silica also increased from 7.5J/$\textrm{cm}^2$ to 15J/$\textrm{cm}^2$. For the irradiation of a 266 nm high-intensity and high-repetition laser light, the surface lifetime of CLBO and fused silica could be more doubled compared with that of the as-polished surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.9 s.186
• /
• pp.164-173
• /
• 2006

The cooling capacity of a micro-heat pipe is mainly governed by the magnitude of capillary pressure induced in the wick structure. For microchannel wicks, a higher capillary pressure is achievable for narrower and deeper channels. In this study, a metallic micro-heat pipe adopting high-aspect-ratio microchannel wicks is fabricated. Micromachining of high-aspect-ratio microchannels is done using the laser-induced wet etching technique in which a focused laser beam irradiates the workpiece placed in a liquid etchant along a desired channel pattern. Because of the direct writing characteristic of the laser-induced wet etching method, no mask is necessary and the fabrication procedure is relatively simple. Deep microchannels of an aspect ratio close to 10 can be readily fabricated with little heat damage of the workpiece. The laser-induced wet etching process for the fabrication of high-aspect-ratio microchannels in 0.5mm thick stainless steel foil is presented in detail. The shape and size variations of microchannels with respect to the process variables, such as laser power, scanning speed, number of scans, and etchant concentration are closely examined. Also, the fabrication of a flat micro-heat pipe based on the high-aspect-ratio microchannels is demonstrated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.347.1-347.1
• /
• 2016

Screen printing is commonly used to form the electrode for crystalline silicon solar cells. However, it has caused high resistance and low aspect ratio, resulting in decrease of conversion efficiency. Accordingly, Ni/Cu/Ag plating method could be applied for crystalline silicon solar cells to reduce contact resistance. For Ni/Cu/Ag plating, laser ablation process is required to remove anti-reflection layers prior to the plating process, but laser ablation results in surface damage and then decrease of open-circuit voltage and cell efficiency. Another issue with plating process is ghost plating. Ghost plating occurred in the non-metallized region, resulting from pin-hole in anti-reflection layer. In this paper, we investigated the effect of Ni/Cu/Ag plating on the electrical properties, compared to screen printing method. In addition, phosphoric acid layer was spin-coated prior to laser ablation to minimize emitter damage by the laser. Phosphorous elements in phosphoric acid generated selective emitter throughout emitter layer during laser process. Then, KOH treatment was applied to remove surface damage by laser. At this step, amorphous silicon formed by laser ablation was recrystallized during firing process and remaining of amorphous silicon was removed by KOH treatment. As a result, electrical properties as Jsc, FF and efficiency were improved, but Voc was lower than screen printed solar cells because Voc was decreased due to surface damage by laser process. Accordingly, we expect that efficiency of solar cells could be improved by optimization of the process to remove surface damage.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.27-34
• /
• 1999

We investigated the effect of mechanical back side damage in viewpoint of electrical and surface morphological characteristics in Czochralski silicon wafer. The intensity of mechanical damage was evaluated by minority carrier recombination lifetime by laser excitation/microwave reflection photoconductance decay technique, atomic force microscope, optical microscope, wet oxidation/preferential etching methods. The data indicate that the higher the mechanical damage degree, the lower the minority carrier lifetime, and surface roughness, damage depth and density of oxidation induced stacking fault increased proportionally.

• Korean Journal of Acupuncture
• /
• v.31 no.2
• /
• pp.56-65
• /
• 2014

Objectives : The purpose of this study is to compare the effects of laser acupuncture to the 830 nm on the five transport points with the spleen meridian for treatment to intestinal disease in rat with dextran sulfate sodium(DSS)-induced colitis. Methods : Colitis was induced by DSS for 20 days. The laser therapy on the five transport points of spleen meridian (Laser Well Point-SP1(L-WE), Laser Brook Point-SP2(L-BR), Laser Stream Point-SP3(L-ST), Laser River Point-SP5(L-RI) and Laser Sea Point-SP9(L-SE) was practiced twice a week for 5 times. Colon length was measured using a measuring point. Histological evaluation of colitis was conducted by hematoxylin and eosin(H&E) staining. Reverse transcription polymerase chain reaction(RT-PCR) was determined using western blotting and quantitative reverse-transcriptase polymerase chain reaction, respectively. Results: Colon length increased significantly L-BR and L-ST points after 5 times of therapy. Damage to the colonic mucosa is an integral feature of the DSS model, so control colonic mucosa tissue was damaged in the areas of ulceration resulting in complete epithelial loss. However histological damage decreased on the epithelial lining at all points. Cyclooxygenase(COX)-2 concentrations decreased in all points groups and Interferon(IFN)-${\gamma}$ increased in L-WE, L-BR, L-RI and L-SE points but L-ST was decreased when compared with control. White blood cell(WBC) and neutrophils(NE) decreased after the fifth acupuncture on the all points. But hemoglobin(HGB) increased after the fifth acupuncture on the L-WE, L-BR, L-ST and L-RI points. Also Mean corpuscular hemoglobin(MCH) and Mean corpuscular hemoglobin concentration(MCHC) decreased after the fifth acupuncture on the all points. Conclusions: The present study indicated that five transport points of the spleen meridian can prevent the development of DSS-induced colitis in rat. Thereby suggesting that should be available for decreasing DSS-induced inflammation in a colonic mucosa of tissue.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.297.2-297.2
• /
• 2016

Photoacoustic generation of ultrasound is an effective approach for development of high-frequency and high-amplitude ultrasound transmitters. This requires an efficient energy converter from optical input to acoustic output. For such photoacoustic conversion, various light-absorbing materials have been used such as metallic coating, dye-doped polymer composite, and nanostructure composite. These transmitters absorb laser pulses with 5-10 ns widths for generation of tens-of-MHz frequency ultrasound. The short optical pulse leads to rapid heating of the irradiated region and therefore fast thermal expansion before significant heat diffusion occurs to the surrounding. In this purpose, nanocomposite thin films containing gold nanoparticles, carbon nanotubes (CNTs), or carbon nanofibers have been recently proposed for high optical absorption, efficient thermoacosutic transfer, and mechanical robustness. These properties are necessary to produce a high-amplitude ultrasonic output under a low-energy optical input. Here, we investigate carbon nanotube (CNT)-polydimethylsiloxane (PDMS) composite transmitters and their nanostructure-originated characteristics enabling extraordinary energy conversion. We explain a thermoelastic energy conversion mechanism within the nanocomposite and examine nanostructures by using a scanning electron microscopy. Then, we measure laser-induced damage threshold of the transmitters against pulsed laser ablation. Particularly, laser-induced damage threshold has been largely overlooked so far in the development of photoacoustic transmitters. Higher damage threshold means that transmitters can withstand optical irradiation with higher laser energy and produce higher pressure output proportional to such optical input. We discuss an optimal design of CNT-PDMS composite transmitter for high-amplitude pressure generation (e.g. focused ultrasound transmitter) useful for therapeutic applications. It is fabricated using a focal structure (spherically concave substrate) that is coated with a CNT-PDMS composite layer. We also introduce some application examples of the high-amplitude focused transmitter based on the CNT-PDMS composite film.