• Structural Engineering and Mechanics
• /
• 제70권6호
• /
• pp.781-791
• /
• 2019

Earthquakes most often induce damage to structures, resulting in the degradation or deterioration of integrity. In this paper, based on the experimental study on 5 RC frames with different span length and different layout of buckling-restrained braces, the seismic damage evaluation law of RC frame with buckling-restrained braces was analyzed, and then the seismic damage for different specimens was calculated using different damage models to study the damage evolution. By analyzing and comparing the observation in test and the calculated results, it could be found that, damage evolution models including Gosain model, Hwang model as well as Ou model could better simulate the development of damage during cyclic loading. Therefore, these 3 models were utilized to analyze the development of damage to better demonstrate the evolution law for structures with different layout of braces and under different axial compression ratios. The results showed that from all layouts of braces studied, the eccentrically braced frame behaved better under larger deformation with the damage growing slowly. It could be deduced that the link beam benefited the seismic performance of structure and alleviated the damage by absorbing high values of energy.

• 한국사회복지학
• /
• 제49권
• /
• pp.296-318
• /
• 2002

The purpose of this study is to empirically analyze whether or not, if a community social service center was affiliated with a governing body running other community social service centers, the center would have better organizational performance in comparing to an independently running center. Data was collected from a nationwide mailed and self-administered survey, which 237 centers out of 343 community social service centers responded. Even if, the response rate was 72%, 218 centers were finally analyzed due to the weakness of reliability and incompleteness. By the way, measurement of organizational performance as the dependent variable has been substituted of the results of nationwide organizational evaluation project as the secondary data. One of findings is that 68% of 218 responding centers appeared to be affiliated with a governing body which running more than three other centers, while 41% being affiliated with a body which running more than five other centers. However, a logistic regression analysis which using organizational performance as the dependent variable, has failed to verify the hypothesis that a center which affiliated with a governing body running other centers has better organizational performance when comparing to an independent center. The researcher assumes that a part of governing bodies has better performance and improves competitiveness while the other larger part of them pursues simple organizational growth. Thus, this situation made that the overall evaluation of being affiliated with a large governing body was not positive.

• 반도체디스플레이기술학회지
• /
• 제10권1호
• /
• pp.63-73
• /
• 2011

Metamorphic HEMTs (MHEMTs) have emerged as excellent challenges for the design and fabrication of high-speed HEMTs for millimeter-wave applications. Some of improvements result from improved mobility and larger conduction band discontinuity in the channel, leading to more efficient modulation doping, better confinement, and better device performance compared with conventional pseudomorphic HEMTs (PHEMTs). For the optimized device design and development, we have performed the calibration on the DC characteristics of our fabricated 0.1 ${\mu}m$ ${\Gamma}$-gate MHEMT device having the modulation-doped $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}$As heterostructure on the GaAs wafer using the hydrodynamic transport model of a commercial 2D ISE-DESSIS device simulator. The well-calibrated device simulation shows very good agreement with the DC characteristic of the 0.1 ${\mu}m$ ${\Gamma}$-gate MHEMT device. We expect that our calibration result can help design over-100-GHz MHEMT devices for better device performance.

• 한국식품영양과학회지
• /
• 제28권6호
• /
• pp.1275-1282
• /
• 1999

To investigate the effect of flour brew with bifidobacteria on bread characteristics, flour brew with bifidobacteria was added to baking after 16 hour incubation at 37oC. The more addition of flour brew, the higher gassing power, the better machinality of dough were obtained, resulting in the larger specific volume of bread. Flavor profile analyzed by Electronic Nose System showed that flavor components of 30% flour brew were decreased comparing with those of control and there was shown definite difference in sensory characteristics between them. Staling studies of bread containing flour brew indicated had a definite effect in retarding the staling rate of bread, with time constant calculated in 30% treatment being 3.09 days and in control being 2.08 days. The enthalphy of gelatinization was decreased from 2.51J/g to 0.61J/g with increment of flour brew, suggesting that starch crystallization is delayed. conclusion, Flour brew fermented by bifidobacteria can be used as a natural bread improver with so many benefits as better machinality, one more day storage period, slower staling rate, better bread volume and more appealing bread flavor.

• 한국인터넷방송통신학회논문지
• /
• 제9권4호
• /
• pp.129-138
• /
• 2009

TV방송에서의 문자그래픽(방송자막)은 영상정보에 대한 시청자의 이해를 돕고 프로그램의 가치를 높여주는 영상구성 요소로써의 역할이 확대되고 있다. 본 논문은 TV화면의 대형화와 영상의 고품질화에 적합한 글자 표현을 위해 방송문자의 글꼴, 크기, 색상, 이동속도 등 문자의 속성에 변화가 필요한 점을 찾고 그 개선 방법에 관한 연구이다. 논문에서는 이론적 고찰과 함께 전문가 그룹을 대상으로 한 델파이조사를 기반으로 TV화면의 분자가 지닌 제 특성요소와 시각적 인지도가 어떤 연관을 가지고 있는지를 고찰하고 OSMU(One Source Multi Use) 환경에서의 각 매체별 특성을 고려한 개선안을 제안한다.

• 가정과삶의질연구
• /
• 제7권2호
• /
• pp.61-70
• /
• 1989

The present study investigated characteristics of Korean hourehelds in the expanding stage of the family life cycle depending on decision-making of current and planned credit card use. Households which were selected for this study had at least one dependent child enrolled in primary, middle, or high school, 1998. Regarding current and planned credit card use, credit card holder (n=379) and non-holder (n=259) households and continuous (n=331) and discontinous (n=47) credit card holder households were compared. Comparisons were perfomed by t-test, one-way ANOVA, and X2-test. Related factors were households demographic characteristics, financial management behavior, perceived financial well-being, and attitudes toward credit cards. Findings indicated that holder households tended to be younger, better educated, white-collar workers, and of a higher economic status than non-holders. In comparison to non-holder households, credit card holder households had more favorable atti udes toward credit cards, reported more financial management practices, experienced less financial unbalance, and were more satisfied with their household finaces. Compared to discontinuous credit card holder households, continuous card holder households tended to be larger, have better educated wives and husbands, and have husbands who were white-collar workers. They were more likely to have higher average monthly income than discontinuous holder households. Continuous card holder households also had more favorable attitudes toward credit cards, and more strongly believed and expected financial improvement of their households, compared to discontinuous card holder households.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1235-1244
• /
• 1994

In this study, experimental results of the nucleate boling of wire-wrapped tubes are provided. Both water and R-113 were boiled. Solid stainless steel wires, stranded copper wires and stranded nylon wires were tested. Solid stainless wire is effective to enhance the boiling of water. The performance is approximately the same(or slightly better at certain conditions) as that of GEWA-T tubes. For the test range of wire diameter 0.6 $mm{\le}d{\le}2.6 mm$, the optimum gap width increases as the wire diameter increases. The maximum heat transfer coefficient was obtained for the 1.0 mm diameter wire, and it is 1.6 times larger than that of the GEWA-T at the heat flux of 20 $kW/m^{2}.$ Solid stainless wire is also effective to enhance the boling of R-113 at low heat fluxes. The performance of the wire-wrapped tube approaches that of GEWA-T. At high heat fluxes, however, the enhancement decreases. The reason may be attributed to the cavity shape and the high wettability of the refrigerants. Stranded copper or nylon wire is effective to enhance the boiling of R-113. The performance is approximately the same(or slightly better) as that of GEWA-T tubes. Maximum heat transfer was obtained for the stranded nylon wire, and it is approximately 1.4 times larger than that for the GEWA-T at the heat flux of 20 $kW/m^{2}.$ The reason may be atrributed to the favorable thermal environment in the restricted regions formed by twisted wires.

• 지질공학
• /
• 제32권3호
• /
• pp.389-399
• /
• 2022

Observations on the influence of the fluid infiltration on the breakdown pressure during laboratory hydraulic fracturing tests, along with an analysis of the applicability of the breakdown pressure prediction for cylindrical samples using Quasi-static and Linear Elastic Fracture Mechanics approaches were carried out. These approaches consider fluid infiltration through the so-called radius of fluid infiltration or crack radius, a parameter that is not a material property. Two sets of tests under pressurization rate controlled and injection rate controlled tests were used to evaluate the applicability of these methods. The difficulty of the estimation of the radius of fluid infiltration was solved by back calculating this parameter from an initial set of tests, and later, the obtained relationships were used to predict breakdown pressures for a second set of tests. The results showed better predictions for the injection rate than for the pressurization rate tests, with average errors of 3.4% and 18.6%, respectively. The larger error was attributed to differences in the testing conditions for the pressurization rate tests, which had different applied vertical pressures. On the other hand, for the tests carried out under constant injection rate, the Linear Elastic Fracture Mechanics solution reported lower errors compared to the Quasi-static solution, with values of 3% and 3.8%, respectively. Moreover, a sensitivity analysis illustrated the influence of the radius of fluid penetration or crack radius and the tensile strength on the breakdown pressure, suggesting a need for a careful estimation of these values. Then, the calculation of breakdown pressure considering fluid infiltration in cylindrical samples under triaxial conditions is possible, although larger data sets are desirable to validate and derive better relations.

• Journal of the Korean Wood Science and Technology
• /
• 제10권3호
• /
• pp.135-151
• /
• 1982

In order to investigate the effectiveness of Osmose process for the practical treatment of wood this study has been made using water soluble preservatives such as Malenit and chromated zinc chloride. The results obtained in this investigation are as follows: 1. The penetration of Malenit in sapwood has been observed deeper than that of chromated zinc chloride for all species tested in this investigation. 2. The penetration of preservatives applied in soft wood, ie. Pinus densiflora and Larix leptolepis has been observed better results than that of hard wood, i.e., Quercus accutissima and Carpinus laxiflora. 3. The longer stack covering, despite of preservatives applied and size of wood tested, has given better penetration for all species tested, and the fastest diffusion has been occured in 15 days from they day started. Following after 15 days diffusion had gradualy become slower. 4. The length of time needed for effective penetration has taken 45 days for all species tested, reaching twenty millimeters (20mm) in depth in case of Malnit, that means also more than 50% of penetration into sapwood portion. However it has taken 45 days fer Pinus densiflora and Larix leptolepis, reaching fifteen millimeters (15mm) and 60 days for Quercus accutissima and Carpinus laxiflora, reaching same fifteen millimeters in case of chromated zinc chloride, that means also less than 50% (except 50% for Larix) of penetration into sapwood portion. 5. Deeper penetration of preservatives from the wood surface has been observed in the larger wood than the smaller wood for all species tested, although the penetration ratio between the width of sapwood and the length penetrated has been observed smaller in larger wood than smaller wood. 6. The relation between moisture content of wood and the penetration of preservatives into wood tested has shown the linear regression, that is, the more moisture content brought the deeper penetration. 7. Following the result obtained at this investigation osmose process with Malenit applied has indicated as a useable process for the none pressure treatment of wood.

• Structural Engineering and Mechanics
• /
• 제75권6호
• /
• pp.785-797
• /
• 2020

As the growth of world trade has surged rapidly over the past years, the number is expected to continue growing over the coming years. Although the transportation costs can be reduced by using larger vessels, however, new berthing structures have to be constructed in order to cater for the larger vessels. This leads to a need for researching on designing a better berthing structure. For optimization of berthing structure design, we need to provide a better estimation of berthing energy than the previous methods in the existing guidelines. In this study, several berthing parameters were collected from previous works and researches. Moreover, the scenarios were selected efficiently by using a sampling technique. First, the berthing energy was calculated by executing 150 numerical simulations. Then, the numerical simulation results were compared with the results calculated by existing methods quantitatively to investigate the sensitivity of the berthing parameters and the accuracy of existing methods. The numerical method results have shown some deviation with respect to the existing method results in which the degree of deviation varies with the methods and the tendency of differences is dependent on certain berthing parameters. Then, one of the existing methods which has shown a small deviation was selected as a representative method and applied with several safety factors to obtain a suitable safety factor for the design.