• Interaction and multiscale mechanics
• /
• v.4 no.2
• /
• pp.155-164
• /
• 2011

The lattice strain evolution within polycrystalline solids is influenced by the crystal orientation and grain interaction. For multi-phase polycrystals, due to potential large differences in properties of each phase, lattice strains are even more strongly influenced by grain interaction compared with single phase polycrystals. In this research, the effects of the grain interaction and crystal orientation on the lattice strain evolution in a two-phase polycrystals are investigated. Duplex steel of austenite and ferrite phases with equal volume fraction is selected for the analysis, of which grain arrangement sensitivity is confirmed in the literature through both experiment and simulation (Hedstr$\ddot{o}$m et al. 2010). Analysis on the grain interaction is performed using the results obtained from the finite element calculation based on the model of restricted slip within crystallographic planes. The dependence of lattice strain on grain interactions as well as crystal orientation is confirmed and motivated the need for more in-depth analysis.

• Advances in aircraft and spacecraft science
• /
• v.1 no.1
• /
• pp.93-123
• /
• 2014

A variational asymptotic composite beam model has been developed for thermoelastic analysis. Composite beams, including sandwich structure and laminates, under different boundary conditions are examined. Previously developed beam model, which is based on variational-asymptotic method, is extended to incorporate temperature-dependent materials experiencing large temperature changes. The recovery relations have been derived so that the temperatures, heat fluxes, stresses, and strains can be recovered over the cross-section. The present theory is implemented into the computer program VABS (Variational Asymptotic Beam Sectional analysis). Numerical results are compared with the 3D analysis for the purpose of demonstrating advantages of the present theory and use of VABS.

• Microbiology and Biotechnology Letters
• /
• v.23 no.5
• /
• pp.580-587
• /
• 1995

In order to produce the bacteriolytic enzyme, bacterial strains capable of excreting a large amount of the enzyme were screened from the coastal sea water samples in Pusan. The bacterial strain SH-1, which showed the highest activity among 43 bacteriolytic enzyme producing bacteria, was finally selected for further studies. The strain SH-1 was an endospore-forming grampositive rod, and the position of spore was paracentral. These morphological characteristics assigned the isolated strain to the morphological group I classified by Gordon. The fatty acid composition of the bacterial stain was analyzed to be consisted of branched chains of iso-Cn and anteiso-Cn. Based on the percent content of the branched chain (93.85%), the isolates could be identified as a species of Bacillus. According to the experimental results of the API system (API 50CHB & API 20E) the strain was identified as Bacillus subtilis. Numerical texonomy, in which 82 major characters were examined using several species of Bacillus as the standard bacteria, indicated that the strain SH-1 showed 90% similarity to Bacillus subtilis. Thus, the isolated strain SH-1 could be identified as Bacillus subtilis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.1
• /
• pp.69-73
• /
• 2001

In this study, we fabricated Bi-2223/Ag high temperature superconducting tapes using PIT(Powder-In-Tube) process to apply the superconducting magnet, cable and etc. It is inevitable to deform the superconducting taps with axial strain for application. Therefore, for the characterization of the strain sensitivity of the superconducting properties, the degradation of Bi-2223/Ag tapes due to axial strain were investigated by measuring the critical current as a function of applied tension strain and external magnetic field. The critical current of Bi-2223/Ag tapes were decreased slightly up to 0.3∼0.4% applied strain but, drastically decreased more than these strains. Superconducting filament cores consisted of brittle ceramic fibers were broken easily by the large strain and current path were decreased simultaneously.

• Transactions of Materials Processing
• /
• v.24 no.5
• /
• pp.361-367
• /
• 2015

The forming limit diagram (FLD) is the most commonly used tool for evaluating of sheet metal formability in the manufacturing field as well as the finite element analysis (FEA)-based design process. Determination of the forming limits is considerably influenced by testing/measuring machines, techniques and conditions. These influences may cause a large scatter in FLD from laboratory to laboratory. Scatter is especially true when the ‘position-dependent method’, as is specified in most national and international standards, is used. In the current study a new ‘time-dependent method’ is proposed, which is to determine the forming limit strains more accurately and reasonably when producing a FLD from experimental data. This method is based on continual strain measurement during the test. The results are compared to those from the existing standardized methods.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.327-332
• /
• 1998

Drying shrinkage means the reduction of volume of concrete because of the loss of water in concrete. This shirinkage can cause tensile stresses, crack formations at the exposure surfaces in concretes. The purpose of this paper is to apply differential shrinkage model which uses moisture diffusion equation and to calculate more reasonable shrinkage quantity, the stresses of concretes. The result of this papar is that the mean value of differential shrinkage is similar to the existing result but at exposures surface the shrinkage strains are more large. From this result the possiblility of crack formation can take place. Thus a resonable counterplan for tensile stresses in exposure surfaces is necessary.

• ALGAE
• /
• v.30 no.4
• /
• pp.275-280
• /
• 2015

Coolia santacroce is a newly described epibenthic dinoflagellate species collected from the U.S. Virgin Islands. The original description indicates this species is unique from others in the Coolia monotis complex due to the relative size of the apical pore complex, broad range of pore sizes, and ribosomal DNA. The original description was done based on the isolation and cultivation of one isolate of the organism. In this study, we report three more isolates of Coolia santacroce collected from the Bahamas. Morphological observations were made using scanning electron microscopy that do not correspond to those from the original description, indicating the variability of the morphological features. However, analysis of the D1 / D2 regions of the large subunit rDNA places the three strains in a strongly supported monophyletic clade with the type specimen.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.230-239
• /
• 2004

A compact model approach of a network of spring elements for elastic loading is presented for the thermal deformation analysis of BGA package assembly. High-sensitivity moire interferometry is applied to evaluate and calibrated the model quantitatively. Two ball grid array (BGA) package assemblies are employed for moire experiments. For a package assembly with a small global bending, the spring model can predict the boundary conditions of the critical solder ball excellently well. For a package assembly with a large global bending, however, the relative displacements determined by spring model agree well with that by experiment after accounting for the rigid-body rotation. The shear strain results of the FEM with the input from the calibrated compact spring model agree reasonably well with the experimental data. The results imply that the combined approach of the compact spring model and the local FE analysis is an effective way to predict strains and stresses and to determine solder damage of the critical solder ball.

• Steel and Composite Structures
• /
• v.21 no.4
• /
• pp.775-789
• /
• 2016

This paper presents the flexural behavior & ultimate strength performance of innovative light weight sandwich panels of size $3{\times}1.2m$ with two different solidity ratios viz. 0.5 and 0.33 under out of plane bending load. From the experimental studies, it is observed that the flexural strength and the stiffness are increased by about 46% and five folds for lesser solidity ratio case. From the measured strains of the shear connectors, full shear transfer between the concrete wythes is observed. The yielding occurred approximately at 4% and 0.55% of the ultimate deformation for 100 mm & 150 mm thick panels, which shows the large ductility characteristics of the panels. From the study, it is inferred that the light weight sandwich panels behave structurally in a very similar manner to reinforced concrete panels. Further from the numerical study, it is observed that the numerical values obtained by FE analysis are in good agreement with the experimental observations.

• Applied Microscopy
• /
• v.45 no.2
• /
• pp.63-73
• /
• 2015

Shear banding is an evidence of plastic instability that localizes large shear strains in a relatively thin band when a material is plastically deformed. Shear bands have attracted much attention in amorphous metals, because shear bands are the key feature that controls the plastic deformation process. In this article, we review recent advances in understanding of the shear bands in amorphous metals regarding: dislocations versus shear bands, the formation of shear bands, hot versus cold shear bands, and property manipulation by shear band engineering. Although there are many key issues that remain puzzling, the understanding built-up from these approaches will provide a new insight for tailoring shear bands in amorphous metals, which potentially leads to unique property changes as well as improved mechanical properties. Indeed, this effort might open a new era to the future use of amorphous metals as a new menu of engineering materials.