• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.1
• /
• pp.47-52
• /
• 2021

Recently, the share of wind power in energy markets has sharply increased with the active development of renewable energy internationally. In particular, large-scale wind farms are being developed far from the coast to make use of abundant wind resources and to reduce noise pollution. In addition to the electromagnetic interference (EMI) caused by offshore wind farms to coastal or air surveillance radars, it is necessary to investigate the EMI on global maritime distress and safety system (GMDSS) communications between ship and coastal stations. For this purpose, this study investigates whether the transmitted field of MF/HF band from a ship would be subject to interference or attenuation below the threshold at a coastal receiver. First, using geographic information system digital maps and 3D CAD models of wind turbines, the area of interest is electromagnetically modeled with patch models. Although high frequency analysis methods like Physical Optics are appropriate to analyze wide areas compared to its wavelength, the high frequency analysis method is first verified with an accurate low frequency analysis method by simplifying the surrounding area and turbines. As a result, the received wave power is almost the same regardless of whether the wind farms are located between ships and coastal stations. From this result, although wind turbines are large structures, the size is only a few wavelengths, so it does not interfere with the electric field of MF/HF distress communications.

• Journal of Korean Ophthalmic Optics Society
• /
• v.16 no.4
• /
• pp.383-390
• /
• 2011

Purpose: The present study was conducted to investigate whether refractive powers of soft contact lenses were induced by the deposition of tear proteins when wearing soft contact lenses. Methods: The soft contact lenses (material: etafilcon A, hilafilcon A and comfilcon A) with refractive powers of -1.00 D, -3.00 D, -5.00 D and -7.00 D were incubated in artificial tear for 1 day, 3 days, 5 days, 7 days and 14 days, respectively. After incubation, their refractive powers were measured by wet cell method with an auto-lens meter and their protein deposited on the lenses was determined by the method of Lowry. Results: Among three types of soft contact lenses, the most protein deposition was detected in ionic etafilcon A lens material and significant change of its refractive power was manifested. In other words, refractive powers of etafilcon A lenses firstly decreased after 1 day incubation in artificial tear and then gradually increased with increasing incubation period again. The observed change in refractive powers of all diopters of etafilcon A material was beyond the scope of standard error and bigger in the lens with lower optical power. On the other hand, non-ionic hilafilcon A showed less protein deposition as much as about 20% in etafilacon A and statistically significant increase of refractive powers with increasing incubation period in artificial tear. The change in refractive power of hilafilcon A was also beyond the scope of the standard of error when incubating in artificial tear and greater in the lens with lower diopter. The least protein deposit was shown in silicone hydrogel lens material, comfilcon A as approximately 10% of it in etafilcon A, indicating less change in refractive power within the standard range of error. Conclusions: The large change of refractive powers that was beyond the scope of standard error by the deposition of tear proteins on soft contact lenses was differently detected depending on lens materials in the current study. Thus, the deposition of tear proteins induced by longer period of lens wearing may be one of the causes that induces blurred vision, suggesting that soft contact lens wearers with the amount of tear proteins may need to choose proper lens material.

• Korean Journal of Optics and Photonics
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2013

In this paper, we report design, fabrication and characterization of the WBRM (Wide Band Receiver Module) for LADAR (LAser Detection And Ranging) application. The WBRM has been designed and fabricated using self-made APD (Avalanche Photodiode) and TIA (Trans-impedance Amplifier). The APD and TIA chips have been integrated on 12-pin TO8 header using self-made ceramic submount and circuit. The WBRM module showed 450 ps of rise time, and corresponding 780 MHz bandwidth. Furthermore, it showed very low output noise less than 0.8 mV, and higher SNR than 15 for 150 nW of MDS(Minimum Detectable Signal). To the author's knowledge, this is the best performance of an optical receiver module for LIDAR fabricated by 200 um InGaAs APD.

• Korean Journal of Optics and Photonics
• /
• v.20 no.1
• /
• pp.1-5
• /
• 2009

Recently, much research has been done for to realizeing nano-scale photonic circuits based on photonic crystal, plasmonics and silicon photonics in order to overcome fundamental limits of electronic circuits. These limits include such as bottleneck of speed, and size that cannot be reduced. Even though several kinds of coupling schemes have been reported, coupling structures are still large when it is compared with the nano-scale optical circuit. In this paper, we proposed using a very thin Fresnel lens while shortening the focal length of the Fresnel lens as much as possible. We proposed, for the first time, to utilize metal slits that are able to use the optical coupling system between a nano-scale optical circuit and the standard single mode optical fiber for overcoming the limitation of focal length shortening of the Fresnel lens. Comparative study has been carried out with a FDTD simulation between normal and metal slit assisted Fresnel lens. From the result of simulation, we can achieve 65% coupling efficiency for the metal-slit Fresnel lens when the focal length of metal-slit Fresnel lens is just $4{\mu}m$. On the other hand, the coupling efficiency of the normal Fresnel lens is about 43%.

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.149-157
• /
• 2004

We have calculated the power extraction efficiency and the lasing wavelength distribution of complex-coupled(CC) DFB lasers above threshold for various｜$\chi$L｜ and facet reflectivity combinations, and we have compared the results with those at threshold. Also, we have investigated the effect of coupling coefficient ratio(CR) and the reflectivity of AR facet on the power extraction efficiency and the lasing wavelength distribution. At threshold, the single mode yield as a function of power extraction efficiency of in-phase(IP) CC DFB lasers is the same as that of anti-phase(AP) CC DFB lasers. Above threshold, however, the single mode yield as a function of power extraction efficiency of IP CC DFB lasers is much larger than that of AP CC DFB lasers. For IP CC DFB lasers, AR-HR combination has high single mode yield and large power extraction efficiency compared to other facet combinations. IP CC DFB laser with AR-HR combination for ｜$\chi$L｜of 0.8 has the highest single mode yield and largest power extraction efficiency above threshold among the cases considered. For AR-HR combination, as CR increases and the reflectivity of AR facet decreases, both single mode yield and power extraction efficiency increase due to the reduction of the spatial hole burning effect. For AR-HR combination, the lasing wavelength of CC DFB laser has distributed over the stopband of DFB. As CR increases, the lasing wavelength concentrates on the long wavelength side for IP CC DFB laser, while on the short wavelength side for AP CC DFB laser. As ｜$\chi$L｜ increases, the width of the wavelength distribution decreases and the lasing wavelength moves to the long wavelength side.

• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.150-158
• /
• 2008

The exact transmission coefficients at the interface between a uniaxial anisotropic medium and an isotropic medium at? oblique incidence are derived by applying the extended Jones matrix method. When the birefringence of the uniaxial anisotropic medium is small ($|n_e-n_o|\;{\ll}\;n_o,\;n_e$), the exact transmission coefficients are compared with those by the conventional extended Jones matrix method by Yeh et al. They showed an excellent agreement with each other. In addition, using the exact transmission coefficients, we calculated the polarization characteristics of a light through a uniaxial medium to an incident light with arbitrary polarization state at? oblique incidence. We compared the transmittances of an unpolarized light through a pair of crossed o-type polarizers by two different methods and calculated the transmittance as the variation of the optical constants of the polarizers to evaluate of the extinction ratio. The polarization analysis method using the exact transmission coefficients can be applied to polarization characteristics of a light through a uniaxial medium with large birefringence as well as to liquid crystals and to optical anisotropic material.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.213-217
• /
• 2020

In this study we report a wet-etching-based fabrication method for adiabatic optical-fiber tapers (OFTs), and describe their adiabaticity and HE₁₁ mode evolution at a wavelength of 1550 nm. The profile of the fabricated system satisfies the adiabaticity properties well, and the far-field pattern from the etched OFT shows that the fundamental HE₁₁ mode is maintained without a higher-order mode coupling throughout the tapers. In addition, the measured far-field pattern agrees well with the simulated result. The proposed adiabatic OFTs can be applied to a number of photonic applications, especially fiber-chip packages. Based on the fabricated adiabatic OFT structures, the optical transmission to the inversely tapered silicon waveguide shows large spatial-dimensional tolerances for 1 dB excess loss of ~60 ㎛ (silicon waveguide angle of 1°) and insertion loss of less than 0.4 dB (silicon waveguide angle of 4°), from the numerical simulation. The proposed adiabatic coupler shows the ultrabroadband coupling efficiency over the O- and C-bands.

• Korean Journal of Optics and Photonics
• /
• v.31 no.5
• /
• pp.218-222
• /
• 2020

In this paper, we have experimentally demonstrated a 2-kW-class spectrally-beam-combined laser with high beam quality, using narrow-linewidth ytterbium-doped polarization-maintaining fiber amplifiers. Five fiber amplifiers with different center wavelengths were implemented for the spectrally-beam-combined laser. The center wavelengths of the five amplifiers were 1062, 1063, 1064, 1065, and 1066 nm, respectively. A phase-modulated laser diode was used as a seed source for each amplifier. The seed sources were modulated by filtered pseudorandom-bit-sequence (PRBS) signals 5 GHz in linewidth. The polarization-maintaining large-mode-area fiber with a core size of 30 ㎛ was used as a delivery fiber to mitigate the stimulated Brillouin scattering (SBS) effect. The laser beams from five amplifiers were spectrally combined by a multilayer dielectric diffraction grating. The maximum output power and beam quality M² of the combined laser were measured to be 2.3 kW and 1.74, respectively.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.35 no.1
• /
• pp.38-50
• /
• 2013

Purpose: The aim of this study is to evaluate the effect and potential of electron beam (E-beam) irradiation treatment to the synthetic bony mixtures composed of hydroxyapatite (HA; Bongros$^{(R)}$, Bio@ Co., Korea) and tricalcium phosphate (${\beta}$-TCP, Sigma-Aldrich Co., USA), mixed at various ratios and of type I collagen (Rat tail, BD Biosciences Co., Sweden) as an organic matrix. Methods: We used 1.0~2.0 MeV linear accelerator and 2.0 MeV superconductive linear accelerator (power 100 KW, pressure 115 kPa, temperature $-30{\sim}120^{\circ}C$, sensor sensitivity 0.1~1.2 mV/kPa, generating power sensitivity 44.75 mV/kPa, supply voltage $5{\pm}0.25$ V) with different irradiation dose, such as 1, 30 and 60 kGy. Structural changes in this synthetic bone material were studied in vitro, by scanning electron microscopy (SEM), elementary analysis and field emission scanning electron microscope (FE-SEM), attenuated total reflection (ATR), and electron spectroscopy for chemical analysis (ESCA). Results: The large particular size of HA was changed after E-beam irradiation, to which small particle of TCP was engaged with organic collagen components in SEM findings. Conclusion: The important new in vitro data to be applicable as the substitutes of artificial bone materials in dental and medical fields will be able to be summarized.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.256-263
• /
• 2007

High NA objective design by using SELFOC materials was studied, and two kinds of objective for optical pick-up were designed. The SELFOC materials have radial gradient index distribution, and it gives additional degree of freedom in optical design. Therefore, we expect that optical design of high NA objective without aspheric surface will be possible. In this study, the variation of ms spot diameter was investigated as a function of quadratic constant and refractive index on axis for various combinations of axial thickness and entrance pupil diameter. For the survey, Code V was used for optimization and evaluation of the objective lenses. The result suggested that larger quadratic constant and higher refractive index on axis could give us better imaging performance for all combinations of axial thickness and pupil diameter. Based on the survey, we designed high NA objectives for DVR. There were two kinds of design solution consisting two spherical SELFOC lenses. The solution I had positive-positive lens configuration with short over-all-length, but it had poor off-axial performance compared with the solution II. The solution II had negative-positive lens configuration with good off-axial imaging performance. But the solution II had some disadvantages, long over-all-length and large diameter of the second lens.