• 한국초전도ㆍ저온공학회논문지
• /
• 제21권3호
• /
• pp.43-46
• /
• 2019

A rare-earth barium copper oxide (REBCO) superconducting magnet was designed using no-insulation (NI) and multi-width (MW) winding techniques. The proposed magnet is comprised of 58 REBCO-wound single pancake coils with a bore size of 240 mm. When the magnet is operated at 20 K, the center magnetic flux density is designed to reach 3 T with an operational current of 169.55 A, 70 % of its critical current. The critical current was evaluated using experimental data of a short REBCO conductor sample. The designed magnet was then simulated using FEM software with uniform current density model. Magnetic field and mechanical properties of the magnet are evaluated using the simulated data. This magnet was designed as one of the base designs for the project "Tesla-Level Magnets with Large Bore Sizes for Industrial Applications" which was initiated in 2019, and will be wound using REBCO wires with the defect-irrelevant-winding (DIW) technique incorporated to reduce the overall manufacturing cost.

• 대한기계학회논문집B
• /
• 제35권6호
• /
• pp.617-624
• /
• 2011

본 연구에서는 사각용기 내에서의 자유표면을 갖는 2차원 슬로싱 문제에 대하여 고찰하였다. 용기 내부의 유동은 수평방향의 조화운동을 통해 형성되며, 외부 가진 속도는 u=Asin($2{\pi}ft$)으로 정의 된다. 여기서 u, A�� 그리고 f는 외부로부터 작용하는 가진 속도, 변위 그리고 주파수를 각각 나타낸다. 큰 변위(A~O(1)) 슬로싱 문제의 해석을 위한 실험설비를 구축하였으며, 광범위한 영역에서의 PIV실험을 수행하였다. 실험을 통해 자유표면의 움직임(motion)을 각각 서로 다른 물리적 특성을 갖는 세 가지; 선형 슬로싱의 자유표면의 움직임과 유사한 standing wave motion, 사각용기의 속도가 0을 지나는 순간(the moment of turn-over) 측벽에서 발생하는 run-up motion 그리고 측벽으로부터 내부유체로 점차적으로 전파되는 bore motion으로 분류하였다.

• 디지털융복합연구
• /
• 제11권12호
• /
• pp.665-672
• /
• 2013

영상의학과에는 다양한 질병을 가진 환자들이 검사를 받는 곳으로 병원감염의 교차 오염이 될 가능성이 큰 부서이다. 특히 자기공명영상(MRI)검사는 다른 검사에 비해 검사시간이 오래 걸려 교차오염에 더욱더 노출이 될 수 있다. 이에 본 연구는 MRI검사장비의 소독실태를 파악하고, 환자와 접촉이 가장 많은 Head coil, 환자 고정용 Block, 밀폐된 공간인 Bore에서의 세균분포도를 파악 하였다. MRI 검사장비의 소독실태는 MRI실 근무자 150명을 대상으로 설문을 실시하였으며, 세균분포의 파악은 10 곳의 의료기관에서 측정하였다. MRI 장비의 세균 분포도결과 Staphylococcus, 등의 다양한 세균들이 발견되었다. MRI실 소독실태 파악결과 Head coil, Block, Bore의 소독은 잘 시행되는 것으로 나타났으며, 소독의 시기는 아침에 1회 소독을 가장 많이 시행 하는 것으로 나타났다. 또한 감염관리자에 따른 소독의 유, 무와 소독의 시기에서는 MRI실 검사자가 감염관리 할 때 잘 시행되는 것으로 나타났다. 환자를 검사한 후 교차오염을 방지하기 위하여 바로 적절한 소독제로 소독을 실시하여 교차오염을 방지하여야 할 것이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.135-135
• /
• 2015

Tubes are of extreme importance in industries as for fluid channels or wave guides. Furthermore, some weapon systems such as cannons use the tubes as gun barrels. To increase the service life of such tubes, a protective coating must be applied to the tubes' inner surface. However, the coating methods applicable to the inner surface of the tubes are very limited due to the geometrical restriction. A small-diameter cylindrical magnetron sputtering gun can be used to deposit coating layers on the inner surface of the large-bore tubes. However, for small-bore tubes with the inner diameter of one inch (~25 mm), the magnetron sputtering method can hardly be accommodated due to the space limitation for permanent magnet assembly. In this study, a new approach to coat the inner surface of small-bore tubes with the inside diameter of one inch was developed. Instead of using permanent magnets for magnetron operation, an external electro-magnet assembly was adopted around the tube to confine the plasma and to sustain the discharge. The electro-magnet was operated in pulse mode to provide the strong axial magnetic field for the magnetron operation, which was synchronized with the negative high-voltage pulse applied to the water-cooled coaxial sputtering target installed inside the tube. By moving the electro-magnet assembly along the tube's axial direction, the inner surface of the tube could be uniformly coated. The inner-surface coating system in this study used the tube itself as the vacuum chamber. The SS-304 tube's inner diameter was 22 mm and the length was ~1 m. A water-cooled Cu tube (sputtering target) of the outer diameter of 12 mm was installed inside of the SS tube (substrate) at the axial position. The 50 mm-long electro-magnet assembly was fed by a current pulse of 250 A at the frequency and pulse width of 100 Hz and 100 usec, respectively. The calculated axial magnetic field strength at the center was ~0.6 Tesla. The central Cu tube was synchronously driven by a HiPIMS power supply at the same frequency of 100 Hz as the electro-magnet and the applied pulse voltage was -1200 V with a pulse width of 500 usec. At 150 mTorr of Ar pressure, the Cu deposition rate of ~10 nm/min could be obtained. In this talk, a new method to sputter coat the inner surface of small-bore tubes would be presented and discussed, which might have broad industrial and military application areas.

• 멤브레인
• /
• 제31권5호
• /
• pp.343-350
• /
• 2021

본 연구에서는 다공성 중공사형 분리막(multi-bore capillary membrane module)을 생물막 반응기(MBR)에 침지시켜 운전시간에 따른 흡입 압력을 측정하였다. 공칭 세공크기가 0.2㎛, 외경이 6.4 또는 4.2 mm이고 육각 형태인 중공사형모듈을 MLSS 8,000 mg/L 활성 슬러지 수용액에 각각 침지시키고 투과 유속, 공기량에 따른 변화를 확인하였다. 여과운전/정지이완(FR) 및 정지이완 시 역세척(FR/BW) 및 사인파형 투과유속 연속운전(SFCO) 방식으로 조작하였다. SFCO의 흡입 압력은 30 L/m²·hr에서 낮았으며, 50 L/m²·hr에서는 FR의 흡입 압력이 높게 나타났다. 또한 외경이 작은 모듈의 흡입 압력 상승이 비교적 낮았으며, 외경이 큰 모듈의 흡입 압력은 높게 상승하였지만 역세척으로 40% 이상 감소시킬 수 있었다.

• 자동차안전학회지
• /
• 제6권1호
• /
• pp.33-40
• /
• 2014

In this study the cylinder liner deformation which is one of the most influencing factors in a diesel engine oil consumption was performed by the finite element analysis on the basic designed structure consisting of the cylinder block, head and liners under the conditions of assembly, thermal and gas loads. Compared with a large number of other cylinder blocks showing remarkable harmonic orders of the liner distortion, results are excellent. Namely. the higher harmonic order amplitudes of the radial liner deformation amount to 1 ~ 2㎛ maximally. The main reason lies in the relatively large wall thickness of the liner which amounts to 8.2% of the bore diameter. Besides, a very stiff and symmetrical cylinder block design in combination with a bolt force introduction approximately 1.5mm below the block top deck have a further share on these results. Therefore excellent low oil consumption can be expected.

• 한국해안·해양공학회논문집
• /
• 제20권4호
• /
• pp.401-412
• /
• 2008

본 연구에서는 3차원수치파동수로내에 쇄파후의 파랑이 대형연직원주구조물에 작용할 때 작용파력과 구조물에 의한 파랑변형을 수치적으로 해석한다. 수치해석법으로 파랑과 구조물과의 비선형상호간섭에 따른 쇄파현상을 포함하는 복잡한 자유수면의 거동특성을 고정도로 해석할 수 있는 3차원Navier-Stokes운동방정식과 자유수면추적에 3차원VOF(Volume Of Fluid)법을 결합한 강비선형해석법을 적용한다. 3차원파동장내에서 해저는 쇄파를 상대적으로 쉽게 발생시킬 수 있는 경사스텝의 해저(변수심의 경사수역과 일정수심역으로 구성)로 이루어진 경우를 고려하며, 파고의 변화에 따라 쇄파가 경사수역 또는 일정수심역에서 발생하여 일정수심역의 대형연직원주구조물에는 쇄파후의 파랑만이 작용하는 경우로 한정한다. 구조물의 위치 및 입사파랑의 파고변화가 구조물에 작용하는 파력 및 파랑변형에 미치는 특성을 쇄파전후의 파랑을 중심으로 검토하고, 쇄파후 파랑의 전파에 따른 파랑에너지의 변화와 구조물에 작용하는 파력특성과를 연관시켜 논의하여 3차원파동장에서 파랑과 구조물과의 강비선형간섭현상의 특성을 규명한다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.185-192
• /
• 1999

It had found that, as a result of cross-hole tonic logging test, concrete was not filled partially within the bottom 2.0 m of the large diameter (Ø= 2,500mm) rock socketed pile, MP20-P11(socket diameter (Ø= 2,200mm), which was a pile among piles group supporting a pier of Kwangan Grand Bridge. The pile was repaired by the combined cement grout injected through the pipes for the cross-hole sonic logging test and the bore holes for core samples. A month after the cement grouting, repairing was checked by coring and cross-hole sonic logging then 3 times of grouting and 2 times of coring were, in turns, peformed, then repairing was completed successfully. The vertical compressive capacity of the repaired large diameter socketed pile was evaluated by several formulas and software ROCKET, and was more conservative than design load (1,882 ton) of MP20-P11. It is expected that, in the case of the battered socketed piles, it could be more reasonable to analyze the behaviors of a battered pile using 3-D model. A 3-D analysis will be peformed in the future study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.376-381
• /
• 2009

The increasing needs for higher cargo capacity in the container vessels' fleet has led to ship builder's demand for higher power output rating engine to meet the propulsion requirement, thus, leading to the development of super large two stroke low speed diesel engines. This large sized bore engines with more than 12 cylinders are capable of delivering power output up to more than 100,000 bhp at maximum continuous rating. The thrust variation force due to axial vibration occurring in propulsion shafting of these ships are transmitted to ship structure via thrust bearing. This force may vibrate the super structure of ship in the fore-aft direction and the fatigue strength of crank shaft can be decreased by additional bending stress increase in crank shaft pin and journal. In this paper, the axial vibration of propulsion shafting system on the 14RT-flex96C super large diesel engine with 14 cylinders is identified by theoretical analysis and vibration measurement.

• 한국분말재료학회지
• /
• 제3권4호
• /
• pp.227-232
• /
• 1996

(i) The development of a metallurgical bond during the spray forming of clad products has offered the possibility of manufacturing large rolls, including those used in hot and cold strip mills. Small rolls are already being produced in Japan. (ii) Technical developments, including the use-of-multi-atomizers have resulted in the elimination of porosity from the internal bore of a sprayed tube. Bimetallic tubing can also be manufactured and the installation of a 4.5 ton tube plant in the USA should provide low operation costs. (iii) Spray forming offers a potentially low cost manufacturing route for superalloy ring/casing components in high strength superalloys. (iv) A large pilot plant has been built for the spray forming of ultra-clean superalloys for turbine disc applications. (v) Using twin-atomizing technology, special steel billets have been spray formed up to 400mm diameter with deposition yields in excess of 90%. (vi) Al/Si alloy extrusion billets with excellent dimensional tolerances are being manufactured for large scale automotive applications. Several new aluminum alloys have also been developed, including high strength, low density and low cocfficient of expansion materials. (vii) New copper alloys have been developed and pilot plants are in operation to produce these alloys once markets have become established.