• Journal of the Korean Institute of Navigation
• /
• v.1 no.1
• /
• pp.17-26
• /
• 1977

A large number of the set-nets are set in Namhaedo coast of Korea. The floats of these set-nets are not only small even in case of large floats but also they scarcely have distinguishable marks such as light buoys or flags, so that they are very hard to be recognized by naked eyes and thus became probable obstacles to navigation for the passing ships and the fishing vessels. In order to research the capability of detecting such nets with Radar, the author investigated a maximum detectable range of the ordinarly large floatsand of a floating corner reflectors of various size and shape by Radar. The results obtained are as follows; 1. A maximum detectable range of large floats at a close range can be calculated by the Radar equation in sufficient accuracy. 2. Large floats of the large set-nets are also detectable by Radar even though it's detectable range boundary was within 0.2-0.65 miles. And the Radar picture of large floats was easier to be found with somewhat higher setting of the gain control on shorter range scale of the 1 mile. 3. Floating corner reflector rather suitable for set-net floats of "S" type reflector proposed in this paper, of which the dimension must be above 17cm in diameter to be detectable by Radar at 2 miles.t 2 miles.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.1
• /
• pp.1-11
• /
• 2017

In this paper, design requirements of the large radar were investigated, and development was performed through the analysis and design. Large radar should be designed by bearing the 75 knot wind force and $20kg/m^2$ ice mass as operating conditions in order to meet structural stability, and driving torque and bearing load were calculated for securing the driving stability. Thermal dissipation analysis was performed considering TRM and DC-DC Converter's limitation temperature by $50^{\circ}C$ ambient temperature condition in order to attain thermal stability, and PSD and shock analysis were carried out by using MIL-STD-810G vibration and shock specification in order to transport and installation of the large radar. As a result, all components of large radar could secure the structural stability more than 2.8 factor of safety, and driving stability was also secured with adequate bearing fatigue life. Thermal stability was attained by allowable max temperature 88.7 C of the TRM, and structural stability for transportation and installation of the large radar was also secured more than 5 factor of safety. After it was transported and installed to the radar site, operating capability was finally verified by rotating the large radar.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.03a
• /
• pp.161-176
• /
• 2002

Collision avoidance is the most important part of a small vessel. Small and mediurn sized ships are surprisingly poor targets for radar reflection and are frequently in danger of being overrun by large vessels, even under good condition of visibility. One of the best way to prevent collisions at sea is to use as large and well designed a radar reflector. Thus, RCS(Radar Cross Section) increase is key element in the design of radar reflector. Radar Reflectors are normally classified into active-type and passive-type. In this paper, the RCS increase methods for passive-type reflector through shaping are explained, and analyzed with RCS performance test by computer simulation. As results from analysis, It is shown that the effective diameter of radar reflector is over 10 λ to provide a return above the threshold RCS of 25m$^2$, lower limit of detectability using X-band radar in a moderate sea.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.1
• /
• pp.50-60
• /
• 2019

Recently, problems with excessive vibration of the radar masts of large bulk carriers and crude oil tankers have frequently been reported. This paper explores a design method to avoid the resonance of a radar mast installed on a large ship using various design of experiment (DOE) methods. A local vibration test was performed during an actual sea trial to determine the excitation sources of the vibration related to the resonant frequency of the radar mast. DOE methods such as the orthogonal array (OA) and Latin hypercube design (LHD) methods were used to analyze the Pareto effects on the radar mast vibration. In these DOE methods, the main vibration performances such as the natural frequency and weight of the radar mast were set as responses, while the shape and thickness of the main structural members of the radar mast were set as design factors. From the DOE-based Pareto effect results, we selected the significant structural members with the greatest influence on the vibration characteristics of the radar mast. Full factorial design (FFD) was applied to verify the Pareto effect results of the OA and LHD methods. The design of the main structural members of the radar mast to avoid resonance was reviewed, and a normal mode analysis was performed for each design using the finite element method. Based on the results of this normal mode analysis, we selected a design case that could avoid the resonance from the major excitation sources. In addition, a modal test was performed on the determined design to verify the normal mode analysis results.

• Journal of Navigation and Port Research
• /
• v.27 no.3
• /
• pp.267-272
• /
• 2003

This paper describes design method of Passive-type Radar Reflector (PRR) which is to provide the requirement of newly revised 2000 SOLAS regulations on the Radar Reflector. The main target of this work is to find the optimum shape of a radar target having large Radar Cross Section (RCS). Through the RCS analysis based on the theoretical approach, two kinds of PRR models, RRR-F model for use in fisheries and PRR-S model for use in small sized ship, are designed and discussed their RCS performance. RCS measurement tests for the various sized samples are carried out in an anechoic chamber. As evaluation results it was clearly shown that the conventional sphere-type shows optimum shape in case of PRR-S, while the cylinder-type which consists of large sized corner clusters or zig-zag flat plats gives best performance in case of PRR-F.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1138-1143
• /
• 2011

One of the critical items in radar testing is the ability to evaluate the performance of radar systems under real operational environments. But it takes lots of time and cost to operate real targets and analyze the test results due to a large amount of data based on these complicated environments. In this paper, the Radar Simulative T&E Lab. is introduced, and the test and analysis results of the developing radar for predicting the radar system performance are described in the Radar Simulative T&E Lab. This laboratory could be used to test the far-field characteristics of antenna radiation pattern and to perform an effective radar system test and evaluation using a simulative target generator under a low cost repeating test situation.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.421-426
• /
• 2005

Scattering center extraction schemes for radar cross section reduction of large complex targets, like warships, was developed, which are an 1-D radar image method(range profile), and a direct analysis based on an object precision method. The analysis result of partial dihedral model shows that the presented direct analysis method is more efficient than the 1-D radar image method for scattering center extraction of interested targets, in terms of radar cross section reduction design, not signal processing. In order to verify the accuracy of the direct analysis method, a scattering center analysis of an naval weapon system was carried out, and the result was coincident with that of another well-known RCS analysis program. Finally, an analysis result of RCS and its scattering center of an 120m class warship-like model presented that the direct analysis method can be an efficient and powerful tools for radar cross section reduction of large complex targets.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.12
• /
• pp.3063-3068
• /
• 2014

Since the RCS(Radar Cross Section) of target is important factor to determine radar performance, it is important to locate radar where large RCS is observed. However, the distance between the target and the radar is an important factor of the received power, as well as RCS. In this paper, it is calculated that received power from ballistic missile to radar based on different observed position and it is studied that to place radar for high detection efficiency.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.2
• /
• pp.187-195
• /
• 2017

We have studied the efficient operation of the radar and the appropriateness of the installation location, when constructing the VTS system. As the Civil-Military Complex Harbour (Kangjeong Port) is completed in 2016, we set the control area within 10 nautical miles centering on Kangjeong Port, and found out and removed the operational radar blind area of VTS system to provide safe navigation information for vessels that navigating this area. Assuming that two international cruise ships entering at the same time, we performed the radar simulation and compared the images by considering the three sites of Kangjeong Port, Miaksan and Seoguipo Port. Simulation results for a single radar installed at Kangjung Port indicate that the blind area was largely affected by two large cruise ships and the surrounding islands. The blind area due to Kogunsan was considerably large when installed in Miaksan, but the blind area due to the influences of Beomseom, Moonseom and Seopseom was negligibly large. It seems that additional radar installation is necessary as a complementary solution to solve this blind area. When two radars were installed at Miaksan and Kangjeong Port, the residual blind area due to the Seopseom was $0.25km^2$ at 0.1~0.33 nautical miles in the southeast direction from Seopseom. In addition, the remaining blind area with two cruise ships mutually influenced was $0.18km^2$, which did not occur with a single cruise ship.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2018

This paper proposes a low complexity super resolution algorithm for frequency modulated continuous wave (FMCW) radar systems for foreign object debris (FOD) detection. FOD radar has a requirement to detect foreign object in small units in a large area. However, The fast Fourier transform (FFT) method, which is most widely used in FMCW radar, has a disadvantage in that it can not distinguish between adjacent targets. Super resolution algorithms have a significantly higher resolution compared with the detection algorithm based on FFT. However, in the case of the large number of samples, the computational complexity of the super resolution algorithms is drastically high and thus super resolution algorithms are difficult to apply to real time systems. In order to overcome this disadvantage of super resolution algorithm, first, the proposed algorithm coarsely obtains the frequency of the beat signal by employing FFT. Instead of using all the samples of the beat signal, the number of samples is adjusted according to the frequency of the beat signal. By doing so, the proposed algorithm significantly reduces the computational complexity of multiple signal classifier (MUSIC) algorithm. Simulation results show that the proposed method achieves accurate location even though it has considerably lower complexity than the conventional super resolution algorithms.