• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.219-221
• /
• 2006

In an attempt to optimize friction spot joining process of Al alloys for automobiles, Friction spot joining was used make lap feint on strips of AA5052-H32 and AA6022-T4 aluminium alloy. The effects of joining parameters such as tool rotating speed, plunging depth, joining time and kind of upper plate on the joints properties were investigated. An optimal tensile shear strength parameter of a tool rotating speed of 1000rpm, dwell time 2.5sec with upper plate 6022 can be found to make a good joint.

• Structural Engineering and Mechanics
• /
• 제4권3호
• /
• pp.313-329
• /
• 1996

A mathematical model of a cable as a system of interacting wires with interwire friction taken into account is presented in this paper. The effect of friction forces and the interwire slip on the mechanical properties of tension cables is investigated. It is shown that the slip occurs due to the twisting and bending deformations of wires, and it occurs in the form of micro-slips at the contact patches and macro-slips along the cable. The latter slipping starts near the terminals and propagates towards the middle of the cable with the increase of tension, and its propagation is proportional to the load. As the result of dry friction, the load-elongation characteristics of the cable become quadratic. The energy losses during the extension are shown to be proportional to the cube of the load and in inverse proportion to the friction force, a result qualitatively similar to that for lap joints. Presented examples show that the model is in qualitative agreement with the known experimental data.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.118-121
• /
• 2002

Polyvinylidene di-fluoride (PVDF) film sensor appeared to be practically useful for the structural health monitoring of composite materials and structures. PVDF film sensors were either attached to or embedded in the graphite/epoxy composite (CFRP) samples to detect the fatigue damage at the bondline of single-lap joints or the tensile failure of unidirectional laminates. PVDF sensors were sensitive enough to detect and determine the crack front in linear location since composites usually produce very energetic acoustic emission (AE). PVDF sensors are extremely cost-effective, as flexible as other plastic films, in low profile as thin as a few tens of microns, and have relatively wide-band response, all of which characteristics are readily utilized for the structural health monitoring of composite structures. Signals due to fatigue damage showed a characteristics of mode II (shear) type failure whereas those from fiber breakage at DEN notches showed that of mode I (tensile) type fracture.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.226-234
• /
• 2000

The friction stir welding technique is a derivative of conventional friction welding, which enables the advantages of solid-phase welding to be applied to the fabrication of long butt and lap joints, with very little postweld distortion. Friction stir welding is a remarkable new welding technique for joining aluminum alloys and has the potential for welding other ferrous materials. It has already been developed beyond a laboratory curiosity and has been proved as a potential practical welding technique offering low-distortion, high-quality, low-cost welds from simple concept machine tool welding equipment. To bring this remarkable method of welding aluminum alloys to the attention of Industry, this article introduces the basic principle of friction stir welding, pointing out the practical advantages and most important of all, describes the exceptionally good metallurgical and mechanical properties.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.83-86
• /
• 2003

동시경화조인트는 경화 시 복합재료로부터 흘러나오는 수지를 접착제로 사용하기 때문에 제조과정이 간편할 뿐 아니라 복합재료를 표면 처리할 필요가 없기 때문에 기존의 접착제에 의한 접합방법에 비해 장점을 지닌다. 최근 동시경화조인트에 관한 연구가 활발하게 진행되고 있으나 해석적인 방법을 통한 연구는 아직까지 미비하다. 실험적으로 연구된 결과를 보면 동시경화 조인트는 계면 모서리에서 파괴가 시작되어 계면을 따라 파괴가 진행된다. 그러므로 조인트의 계면 모서리에서의 응력집중계수에 관해 연구하는 것이 중요하다. 본 논문에서는 고유치 문제를 고려하여 복합재료와 강재료로 구성된 동시경화조인트의 계면 모서리에서 발생하는 응력 및 변위장을 결정하고, H-적분을 이용하여 응력집중계수를 구하는 방법을 제시하고자 한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.115-120
• /
• 2008

In this study, effects of surface roughness on adhesive strength of heat-resistant adhesive RTV88 were examined. Sandblast was used to generate rough surfaces on aluminum adherends, and then tensile-shear tests of Al/RTV88 single lap joints were performed. The shear strength was shown to be affected by the surface roughness. Effective area, peel failure area, and cohesive failure area were introduced to explain the effects of surface roughness on the adhesive strength. An empirical relation for the failure force was proposed based on these parameters and verified by the test results.

• Journal of Welding and Joining
• /
• 제17권3호
• /
• pp.50-54
• /
• 1999

Feasibility study of the application of a developed annealed austenitic stainless steel at cryogenic temperature has been performed for membrane tank of LNG ship. Chemical properties of developed stainless steel are compared with a domestic commercial stainless steel and a foreign stainless steel which are used for LNG ships. Tensile properties at cryogenic temperature and fatigue strength at room temperature are measured for but and lap joints which are TIG welded specimens. Developed stainless steel having a small amount of titanium component shows the finest grain size in the HAZ, compared with the other stainless steel studied. Tensile strength, elongation and fatigue strength of the developed stainless steel are equal to those of the foreign stainless steel studied and are higher than the domestic commercial stainless steel studied.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.67-69
• /
• 2007

Laser welding technology for automobile body is studied. Laser system, robot and seam tracking system are used for 3D laser welding system. The laser system is used 4kW Nd:YAG laser(HL4006D) of Trumpf and the robot system is used IRB6400R of ABB. The seam tracking system is SMRT-20LS of ServoRobot. The welding joints of steel plate are butt and lap joint. The 3 dimensional laser welding for non-linear pipe welding line is performed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.158-160
• /
• 2007

The butt and lap configurational friction stir welding of type 304 stainless steel was conducted in this study. The sound joints were obtained by WC tool. As the welding distance increased, tool deformation gradually increased at the pin edge. The discoloration by oxidation was observed at the top surface of the joint, a sufficient heat-input was required to avoid the welding defect owing to the lack of stirring at the welding start point. Very fine grains were observed in the stir zone, and the grain coarsening was not observed in the heat affected zone.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.103-105
• /
• 2005

Laser welding technology for automobile body is studied. laser system, robot and seam tracking system are used for 3D laser welding system The laser system is used 4kW Nd:YAG laser(HL4006D) of Trumpf and the robot system is used IRB6400R of ABB. The seam tracking system is SMRT-20LS of ServoRobot. The welding joints of steel plate are butt and lap joint. The 3-D welding for non-linear tailored blank is performed after experiments of bead on plate. Finally, the welding process for non-linear tailored blank is developed.