• 열처리공학회지
• /
• 제27권1호
• /
• pp.15-22
• /
• 2014

This study is to investigate the phase changes and cold workability after isothermal transformation at $780^{\circ}C$ by using the high temperature gas nitrided (HTGN) STS 430 ferritic stainless steel specimens. The phase diagram of STS 430 steel obtained by calculation showed that the phase appeared at $1100^{\circ}C$ showed as ${\alpha}+{\gamma}{\rightarrow}{\gamma}{\rightarrow}{\gamma}+Cr_2N{\rightarrow}{\gamma}+Cr_2N+CrN$ with increasing nitrogen concentration. Also, the transformation of ${\gamma}{\rightarrow}Cr_2N$ during heat treatment isothermally at $780^{\circ}C$, nitrogen pearlite with lamellar type was fully formed at the nitrogen permated surface layer for 10 hrs. However, this transformation was not completed for 1 hr, resulting nitrogen pearlite plus martensite. The cold rolled specimen of isothermally transformed at $780^{\circ}C$ for 10 hrs after high temperature gas nitriding decreased the layer thickness of nitrogen pearlite inducing the deformation of hard $Cr_2N$ phase. the dissolution rate of $Cr_2N$ phase increased rapidly with increasing cold rolling ratio. Specimens with the microstructure of nitrogen pearlite (isothermally transformed at $780^{\circ}C$ for 10 hrs) were possible to cold rolling without crack formation. However, the mixed structures of nitrogen pearlite + martensite (isothermally transformed at $780^{\circ}C$ for 1 hr) were impossible to cold deformation without cracking.

• 한국응용과학기술학회지
• /
• 제37권3호
• /
• pp.484-495
• /
• 2020

이 연구는 피부 각질층의 구조와 동일한 구조를 형성하는 혼합계면활성제 (MimicLipidMSM1000)로써 수크로오스다이스테아레이트, 폴리글리세릴-2다이올리에이트, 발효스쿠알란, 에르고스테롤, 10-하이드록시스테아릭애씨드로 이루어진 혼합물을 합성하였다. 이 혼합 계면활성제를 2~5wt%를 사용할 경우, 5~30층의 다중층 라멜라구조를 형성하는 인공 피부 모사체를 만들 수 있었다. 이 혼합계면활성제를 사용하여 에멀젼을 만들고, 다중층의 라멜라 상이 형성되는 것을 메커니즘 적으로 해석하였다. 이 계면활성제의 외관은 연한 갈색의 단단한 왁스이었고, HLB(hydrophilic lipophilic balance)는 12.53이었으며, 임계파라미터 값(critical parameter value)은 0.987, 산가는 0.13이었다. pH변화에 따른 안정성은 산성(3.8), 중성(7.2), 알칼리성(10.8)에서도 안정하였다. 액정의 입경은 5~25mm에서 가장 안정한 십자형 모양 (maltese cross) 라멜라액정 드롭플렛(lamellar crystalline droplet)이 형성됨을 알 수 있었다. 호모믹서의 교반속도 변화에 따른 유화입자의 크기는 2500rpm (17.9mm±2.6mm), 3500rpm (12.5mm±2.1mm), 4500rpm (6.2mm±1.8mm) 속도가 높아 질수록 작은 입자가 형성되었다. 편광현미경을 통하여 액정형성 입자를 관찰하였으며, 주사전자현미경(cryo-SEM)으로 액정의 형성 구조를 정밀하게 분석하였다. 응용분야로써, 각질층의 다중 라멜라 동일한 구조를 형성하는 피부모사체 형성 계면활성제를 사용하여 다양한 스킨케어화장료, 메이크업 케어 화장료, 두피보호용 화장료 등 다양한 처방개발에 폭 넓게 응용이 가능할 것으로 기대한다.

• Fibers and Polymers
• /
• 제7권4호
• /
• pp.358-366
• /
• 2006

Thermotropic liquid crystal polymer (TLCP)-reinforced poly(butylene terephthalate) (PBT) composites were prepared by melt processing. The improvement in the mechanical properties and the processability of the PBT/TLCP composites was attributed to the reinforcing effect by TLCP phase and its well distribution in the PBT matrix. X-ray diffraction results demonstrated that a slow cooling process leads to the thicker lamellar structures and the formation of more regular crystallites in the composites. The incorporation of TLCP improves not only the tensile strength and flexural modulus but also the heat distortion temperature (HDT) of the PBT/TLCP composites. The HDT values of the composites were dependent on TLCP content. The improvement in the HDT values of the PBT/TLCP composites may be explained in terms with the increased flexural modulus, the development of more regular crystalline structures, and the enhancement of the ability of the composites to sustain the storage modulus by TLCP phase. In addition, the simple additivity rule makes it possible to predict the HDT values of the PBT/TLCP composites.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.317-321
• /
• 2012

In this study, Cu-5Ni-10Sn(wt%) spinodal alloy was manufactured by gas atomization spray forming, and the microstructural features and mechanical properties of Cu-5Ni-10Sn alloy have been investigated during homogenization, cold working and age-hardening. The spray formed Cu-5Ni-10Sn alloy consisted of an equiaxed microstructure with a mixture of solid solution ${\alpha}$-(CuNiSn) grains and lamellar-structure grains. Homogenization at $800^{\circ}C$ and subsequent rapid quenching formed a uniform solid solution ${\alpha}$-(CuNiSn) phase. Direct aging at $350^{\circ}C$ from the homogenized Cu-5Ni-10Sn alloy promoted the precipitation of finely distributed ${\gamma}$' or ${\gamma}-(Cu,Ni)_3Sn$ phase throughout the matrix, resulting in a significant increase in microhardness and tensile strength. Cold working prior to aging was effective in strengthening Cu-5Ni-10Sn alloy, which gave rise to a maximum tensile strength of 1165 MPa. Subsequent aging treatment slightly reduced the tensile strength to 1000-1100 MPa due to annealing effects.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.859-860
• /
• 2006

TiC-$TiB_2$-SiC system was a ternary eutectic, whose eutectic composition was 34TiC-$22TiB_2$-44SiC (mol%). TiC-$TiB_2$-SiC ternary eutectic composite were synthesized by a floating zone method using TiC, $TiB_2$ and SiC powders as starting materials. The TiC-$TiB_2$-SiC eutectic composite showed a lamellar texture. TiC(022), $TiB_2(010)$ and SiC(111) of the eutectic composite were perpendicular to the growth direction. TiC-$TiB_2$-SiC ternary eutectic composite had specific relationship among the crystal planes: TiC[011]//$TiB_2[010]$//SiC[112], TiC(200)//$TiB_2$(001)//SiC(402) and $TiC(1\bar{1}1)$//$TiB_2(101)$//SiC(220).

• 한국주조공학회지
• /
• 제11권6호
• /
• pp.455-462
• /
• 1991

The formation of brittle intermetallic compound such as $VAl_3$ tends tp lower the toughness of V-Al alloys. Also, due to the high melting point of vanadium, it is difficult to make that alloy by previous ingot metallurgy method. To depress the technique has been adopted. The effect of particle size and milling time on the phase has been thoroughly studied. For mechanical alloying, SPEX mixed/mill has been used. The milling time and the composition of V and Al are varied to find the optimum condition of forming amorphous phase. The X-Ray Diffrection pattern, microstructure detection, microhandess test, experiments are carried out to analyze MA product. When the final step is reached, no lamellar-structure is detected. The steady state condition is observed after 8 hours and 10 hours milling for 15wt.%Al and 30wt.%Al alloy, respectively. The microhardness continuously increases up to 10 hours after then it remains constant.

• Bulletin of the Korean Chemical Society
• /
• 제7권2호
• /
• pp.120-124
• /
• 1986

In order to investigate effective solar energy conversion system, the light-induced electron transfer reactions have been examined across single-lamellar liposomes incorporated organic photosensitizers such as anthracene and naphthalene derivatives. We have observed photosensitized reduction of methyl viologen (1,1'-dimethyl-4,4'-$bipyridinium^{2+}$) dissolved in the exterior aqueous phase of the pigmented phospholipid liposomes when EDTA, as electron donor, is dissolved in the enclosed aqueous phase of the liposomes. The anthroyl stearic acid incorporated in the hydrophobic bilayer of liposomes leads to much less quantum yield for the photosensitized reduction of $MV^{2+}$ than the anthracene carboxylate incorporated in the outer hydrophilic layer. However, ${\beta}$-carotene with anthroyl stearic acid incorporated into the bilayer enhances the quantum yield significantly (${\Phi}{\simeq}0.2-0.3$), preventing the reverse reaction of electron transfer ($MV^+_\ {\rightarrow}MV^{2+}$) so that it might be useful for solar energy conversion into chemical energy. A naphthalene derivative, octadecyl naphthylamine sulfonic acid incorporated into the outer layer of liposomes results in less efficiency of $MV^{2+}$ reduction than anthroyl stearic acid. These results have been also tested with respect to lipid components of liposomes.

• The Korean Journal of Ceramics
• /
• 제7권2호
• /
• pp.80-84
• /
• 2001

The anisotropic CdS platelets were synthesized in the lamellar bilayer phase region of the octylamine-water binary system. The influence of the synthesis conditions of the system components on morphology and size of the platelets was examined. Atomic force microscopy (AFM) and high-resolution transmission electron microscopy (HRTEM) studies have shown thickness and face size of the synthesized particles. Platelets with face sizes ranging from 50 to 250 nm and thickness from 10 to 30 nm have been synthesized at room temperature. In addition, HRTEM micrographs show that the synthesized platelets are poly crystal.

• 대한치과기공학회지
• /
• 제29권1호
• /
• pp.133-138
• /
• 2007

In this study, the castability and of commercially pure titanium(c.p.Ti) grade according to the casting condition which are the vacuum condition in casting machine and mold temperature of investment, was investigated. Argon-arc melt/centrifugal casting machine was used for casting the specimens. The microstructure and mechanical properties were evaluated by using optical microscope. The results were as follows; 1. It could make a sure that there's relatively not much defect of casting body of c.p.Ti according to the deference of air pressure. 2. It could make sure that it formed porosity on the surface inside of the casting body of c.p.Ti according to deferent temperature. and on excellent castability was below $200^{\circ}C$ 3. As the mold temperature of investment was increased, the lamellar structure of phase and coarse grains were shown, especially under 42MPa.

• 한국주조공학회지
• /
• 제12권2호
• /
• pp.139-148
• /
• 1992

The mechanical properties of Ti-Al intermetallic compounds which contain Mn, Zr, or Cr as the third element have been evaluated by means of hardness and compression tests. Microstructures have also been examined using an optical microscope. The cast structures of Ti-Al alloys are coarsened and the lamellar volume fraction is increased by the additions of Mn or V, but the cast structures are refined by the addition of Zr. Hardness tests of room temperature and compression tests at $600^{\circ}C$ showed that the mechanical properties of Ti-Al alloys were mainly dependent on the volume fraction of the ${\alpha}_2$ phase, grain size and solid solution hardening. However according to the compression test at $1000^{\circ}C$, the yield strength of Ti-Al alloys decreased with an increase in Mn or Cr content, but increased with an increase in the Zr content.